User Manual GETTING STARTED? EASY.
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
• • • • • • • • • • CAUTION: The appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by a utility. CAUTION: The cooking process has to be supervised. A short term cooking process has to be supervised continuously. WARNING: Danger of fire: Do not store items on the cooking surfaces. Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot.
• • • • • • • Keep the minimum distance from other appliances and units. Always take care when moving the appliance as it is heavy. Always use safety gloves and enclosed footwear. Seal the cut surfaces with a sealant to prevent moisture to cause swelling. Protect the bottom of the appliance from steam and moisture. Do not install the appliance adjacent to a door or under a window. This prevents hot cookware falling from the appliance when the door or the window is opened.
WARNING! Risk of fire and explosion • • • • Fats and oil when heated can release flammable vapours. Keep flames or heated objects away from fats and oils when you cook with them. The vapours that very hot oil releases can cause spontaneous combustion. Used oil, that can contain food remnants, can cause fire at a lower temperature than oil used for the first time. Do not put flammable products or items that are wet with flammable products in, near or on the appliance.
Model ....................................... PNC ......................................... Serial number ........................... GAS CONNECTION WARNING! The following instructions about installation, connection and maintenance must be carried out by qualified personnel in compliance with standards and local regulations in force. Choose fixed connections or use a flexible pipe in stainless steel in compliance with the regulation in force.
WARNING! Make sure the flame does not go out when you quickly turn the knob from the maximum position to the minimum position. 4. With a thin screwdriver, adjust the bypass screw position (A). A 5. If you change: • from natural gas G20 20 mbar to liquid gas, fully tighten the bypass screw in. • from liquid gas to natural gas G20 20 mbar, undo the bypass screw approximately 1/4 of a turn (1/2 of a turn for Multi Crown burner). 6. Reassemble the gasket and the knob.
ASSEMBLY 1. 5. 6. 2. 7. 3. min. 100 mm min. 650 mm min. 55 mm 30 mm 480+02 mm 4. +2 560 0 mm CAUTION! Install the appliance only on a worktop with flat surface. POSSIBILITIES FOR INSERTION The panel installed below the hob must be easy to remove and let an easy access in case a technical assistance intervention is necessary.
A min 30 mm A. Removable panel B. Space for connections Kitchen unit with oven B The electrical connection of the hob and the oven must be installed separately for safety reasons and to let easy remove oven from the unit.
BURNER OVERVIEW 2. Keep the control knob pushed for equal or less than 10 seconds. This lets the thermocouple warm up. If not, the gas supply is interrupted. 3. Adjust the flame after it is regular. A If after some tries the burner does not light, check if the crown and its cap are in correct positions. B WARNING! Do not keep the control knob pushed for more than 15 seconds.
HINTS AND TIPS WARNING! Refer to Safety chapters. COOKWARE CAUTION! Make sure that the pots are placed centrally on the burner in order to get the maximum stability and a lower gas consumption. CAUTION! Do not use cast iron pans, clay or earthenware pots, grill or toaster plates. The stainless steel can become tarnished if it is too much heated. ENERGY SAVING • If it is possible, always put the lids on the cookware. • When the liquid starts to boil, turn down the flame to barely simmer the liquid.
4. For the burner to operate correctly, make sure that the arms of the pan supports are aligned with the centre of the burner. CLEANING THE HOB • Remove immediately: melted plastic, plastic foil, sugar and food with sugar, otherwise, the dirt can cause damage to the hob. Take care to avoid burns. • Remove when the hob is sufficiently cool: limescale rings, water rings, fat stains, shiny metallic discoloration. Clean the hob with a moist cloth and a non-abrasive detergent.
Problem The flame ring is uneven. Possible cause Remedy Burner crown is blocked with food residues. Make sure that the injector is not blocked and the burner crown is clean. IF YOU CANNOT FIND A SOLUTION... If you cannot find a solution to the problem yourself, contact your dealer or an Authorised Service Centre. Give the data from the rating plate. Make sure, you operated the hob correctly.
BYPASS DIAMETERS BURNER Ø BYPASS 1/100 mm Multi Crown 56 Semi-rapid 35 Auxiliary 28 OTHER TECHNICAL DATA Gas original: G30/G31 (3B/P) 30/30 mbar 629 g/h TOTAL POWER: Gas replacement: G20 (2H) 20 mbar 9 kW Electric supply: 220-240 V ~ 50-60 Hz Appliance category: II2H3B/P Gas connection: R 1/2" Appliance class: 3 GAS BURNERS FOR LPG G30/G31 30/30 mbar BURNER NORMAL POWER MINIMUM POWNOMINAL GAS FLOW INJECTOR MARK kW ER kW g/h Multi Crown 3,65 1,4 095 265 Semi-rapid 2,0 0,45 71
867356263-B-152019 WWW.ZANUSSI.
