GAS HOBS ZGG 642 ZGG 752 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation l l l l l This hob must be installed by qualified personnel, according to the manufacturers instructions and to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. Remove all packaging before using the hob.
Contents For the Installer For the User Important Safety Information 2 Important safety requirements 10 Description of the Hob 3 Installation 10 Operation 4 Building In 11 Maintenance and Cleaning 4 Electrical connections 12 Something Not Working? 5 Wiring Diagram 13 Service and Spare Parts 5 Fault Finding 13 Guarantee conditions 6 Commissioning 15 Conversion from Natural Gas to LPG 15 Description of the Hob ZGG 642 1 1 4 1 2 ZGG 752 3 3 2 1. Semi-rapid Burners 2.
Operation Hob burners F l l l l To light a burner: push in the relevant control and turn it to maximum position; ZGG 752: upon ignition, keep the knob pushed down about 5 seconds. This will allow the "thermocouple" to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again.
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee.
Customer Care Department For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.zanussi.co.uk Customer Care Department Zanussi 55-77 High Street Slough Berkshire SL1 1DZ 08705 727727 (*) * calls to this number may be recorded for training purposes.
ZANUSSI SERVICE FORCE To contact your local Zanussi Service Force Centre telephone 08705 929 929 CHANNEL ISLANDS GUERNSEY JERSEY Guernsey Electricity PO Box 4 Vale, Guernsey Channel Islands Jersey Electricity Company PO Box 45 Queens Road St Helier Jersey Channel Islands JE4 8NY ORKNEY (M65) Corsie Domestics 7 King Street Kirkwall Orkney KW15 PERTH Hydro Electrical Inveralmond House Ruthervenfield Road Perth PH1 3AQ PERTH (OWN SALES) SCOTLAND ABERDEEN (M05) AUCHTERMUCHY (M03) BLANTYRE (M07) 54 Cla
ZANUSSI SERVICE FORCE To contact your local Zanussi Service Force Centre telephone 08705 929 929 MIDLANDS BIRMINGHAM (M18) 66 Birch Road East Wyrley Road Ind. Estate Witton Birmingham B6 6DB BOURNE Manning Road Ind. Estate Pinfold Road Bourne PE10 9HT (M44) BRIDGNORTH (M72) 68 St. Marys Street Bridgnorth Shropshire WV16 4DR LONDON & EAST ANGLIA 11a Gardener Ind. Estate Kent House Lane Beckenham Kent BR3 1QZ CHELMSFORD (M47) Hanbury Road Widford Ind.
Instructions for the Installer Engineers technical data Ignition HT Spark Spark Generator OVERALL DIMENSIONS Width: Depth: ZGG 642 ZGG 752 580 mm. 510 mm. 680 mm. 510 mm. Spark Gap Semi-rapid Burner Heat Input CUT OUT DIMENSIONS Width: Depth: ZGG 642 ZGG 752 550 mm. 470 mm. 560 mm. 480 mm. Ispra Control's BF 50046 230-240V 0.6 YA T 120 Fixed 1.9 kW (6483 BTU/HR) Rapid Burner Heat Input 2.9 kW Natural Gas (9895 BTU/HR) 2.7 kW L.P.G.
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Part 2 and B.S. 6891 Current Editions. The hob should not be installed in a bed sitting room with a volume of less than 20 m3.
Cut Out Size The dimensions of the cut-out are given in the diagram. ZGG 752 30 480 55 m in. ZGG 642 55 m in. 550 560 150 min FO 2038 FO 2098 Building In 1 ON/OFF SWITCH Building over a cupboard or drawer FLEX OUTLET If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2.
5 A a ZGG 752 5 FO 2321 a) Sealing gasket ZGG 642 FO 2107 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-240V 50Hz AC electrical supply.
Wiring Diagram L 1 A 2 0 3 220/240 4 5 A. IGNITOR SWITCH 6 N Brown B B. IGNITOR UNIT Fault Finding Preliminary Electrical Systems Check Green Yellow Earth Wire Green/Yellow START Isolate appliance and carry out: A: Earth Continuity check. ( ) E( ) FUSE Blue SOCKET (face view) PLUG (with cover removed) Neutral Wire Blue N L Blue Brown Green Yellow NO YES Carry out: C: Polarity check. Has inlet fuse blown? YES NO Inlet wiring faulty. Rectify any fault.
Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Light burner manually Check polarity and earth continuity of supply point Check by pass simmer adjusted Check position of the electrode Check earth continuity of appliance Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from 'L' on the mains connector block and the taps ignition switches Check continuity from igni
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: F Re-ignite the burner and set to MIN. Remove the control knob.
Grafiche MDM - Forlì CUSTOMER CARE Zanussi 55-77 High Street Slough Berkshire, SL1 1DZ Tel: 08705 727727 © Electrolux Household Appliances Limited 2000 From the Electrolux Group. The worlds No.1 choice. The Electrolux Group is the worlds largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx.
