EN User manual Hob ZGG66424 IE GB
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Operation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 7 8 9 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11 Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 1
pliance or hot cookware. Do not let the electricity bonds tangle. Installation • You must read these instructions. The manufacturer is not responsible for any injury to persons and pets or damage to property caused by failure to obey these requirements.
– Cut off the mains cable where it connects with the appliance and discard it. – Flat the external gas pipes if there are fitted. – Speak to your local authorised facilities for disposal of your appliance. Installation Warning! The following instructions about installation, connection and maintenance must be carried out by qualified personnel in compliance with standards and local regulations in force.
not come in touch with mobile parts or they are not squeezed. Also be careful when the hob is put together with an oven. 1 Important! It is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. Important! Failure to ensure the correct assembly will cause leakage of gas. Important! Make sure that the gas supply pressure of the appliance obeys the recommended values.
Electrical Requirements Permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety the installation must be done by a qualified electrician (e.g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting [NICEIC]). The manufacturer declines any liability if these safety measures are not observed.
b) Space for connections A B Kitchen unit with oven The hob recess dimensions must obey the indication and the kitchen unit must be equipped with vents to let a continuous supply of air. The electrical connection of the hob and the oven must be installed separately for safety reasons and to let easy remove oven from the unit.
Control knobs Symbol Symbol Description ignition position / maximum gas supply Description no gas supply / off position minimum gas supply Operation Ignition of the burner Warning! Be very careful when you use open fire in kitchen environment. Manufacturer decline any responsibility in case misuse of the flame 1 2 Always light the burner before you put cookware. 3 To light the burner: 1. Turn the control knob counterclockwise to the maxi) and push it down. mum position ( 2.
If the burner accidentally goes out, turn the control knob to the off position and try to light the burner again after minimum 1 minute. The spark generator can start automatically when you switch on the mains, after installation or a power cut. It is normal. Turning the burner off To put the flame out, turn the knob to the symbol . Warning! Always turn the flame down or switch it off before you remove the pans from the burner.
Warning! Do not use abrasive cleaners, steel wool pads or acids. They can cause damage to the appliance. Scratches or dark stains on the surface have no effect on how the appliance operates. • You can remove the pan supports to easily clean the hob. • To clean the enamelled parts, cap and crown, wash them with warm soapy water and dry them carefully before you put them back. • Wash stainless steel parts with water, and then dry them with a soft cloth. • The pan supports are not dishwasher proof.
Problem Possible cause Remedy The flame is blow out immediately af- • Thermocouple is not heated suffiter ignition cient • After lightning the flame, keep the knob pushed for approximately 5 seconds. The gas ring burns unevenly • Make sure that the injector is not blocked and the burner crown is clear of food particles. • Burner crown is blocked with food residues If there is a fault, first try to find a solution to the problem yourself.
Heat input Gas connection: G 1/2 " II2H3+ Triple Crown burner: 4.0 kW Category: Semi-rapid burner: 2.0 kW Gas supply: Auxiliary burner: 1.
www.zanussi.
www.zanussi.
www.zanussi.
397225901-A-492011 www.zanussi.