EN User manual Hob ZGG66424 IE GB
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Product description _ _ _ _ _ _ _ _ _ _ _ _ _ Operation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 8 8 9 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Environment concerns _ _ _ _ _ _ _ _ _ _ _ 10 11 12 13 Subject to change without notice.
• • • • and that it is centrally positioned on the rings in order to avoid safety risks. Do not use unstable cookware or cookware with damaged bottom. There is a risk of tilting and accident. Do not put flammable products or items that are wet with flammable products, fusible objects (made of plastic or aluminium) and/or fabrics in, near or on the appliance. There is a risk of explosion or fire. Use only the accessories supplied with the appliance.
• Disconnect the appliance from the electrical supply, before you do the maintenance work or you clean it. • The electrical mains terminal is live. • Make electrical mains terminal free of voltage. • Install correctly to give anti-shock protection. • A loose and incorrect mains plug and socket connections can make the terminal become too hot. • A qualified electrician must install the clamping connections correctly. • Use a strain relief clamp on cable.
edges of the hob is 400 mm. If it is fitted below 400 mm a space of 50 mm must be allowed from the edges of the hob. For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S 813 Current Edition Section 7Permitted Locations of Appliance. Gas Connection Make sure that the main connection pipe does not exert any strain on the hob. If you use flexible metal pipes make sure that they agree to ISO 10380 and ISO 10807 standards.
4. With a thin screwdriver, adjust the by-pass screw position. 1 • The electrical installation must have an isolation device which lets you disconnect the appliance from the mains at all poles. The isolation device must have a contact opening width of minimum 3 mm. • You must have the correct isolation devices: line protecting cut-outs, fuses (screw type fuses removed from the holder), earth leakage trips and contactors. • The connection cable parts must not be heated to a temperature above 90°C.
1 Important! The replacement of the electrical cable must be done by a qualified electrician or competent person, according to the current regulations. 2 3 4 5 Replacement of the connection cable To replace the connection cable use only H05V2V2-F T90 or equivalent type. Make sure that the cable section is applicable to the voltage and the working temperature. The yellow/ green earth wire must be approximately 2 cm longer than the brown (or black) phase wire. Building In min.
with vents to let a continuous supply of air. The electrical connection of the hob and the oven must be installed separately for safety reasons and to let easy remove oven from the unit.
2. 3. Keep the control knob pushed for approximately 5 seconds; this will let thermocouple to warm up. If not, the gas supply will be interrupted. Adjust the flame after it is regular. If after some tries the burner does not light, check if the crown and its cap are in correct positions. 1 Warning! Do not keep the control knob pushed for more than 15 seconds.
Burner Diameters of cookware Rear Semi-rapid 120 - 220 mm Auxiliary 80 - 160 mm Warning! Pots must not enter the control zone. Flame will heat up the control zone. Do not put the same pan on two burners. cooktop and that pots are centrally positioned on the rings in order to achieve maximum stability and to obtain lower gas consumption. Do not place unstable or deformed pots on the rings to prevent from spill and injury. Warning! Flame diffuser are not recommended.
The stainless steel can become tarnished if it is too much heated. Refer to this you must not cook with potstones, earthenware pans or cast iron plates. Do not use aluminium foil to prevent damage the top during operation. Removing the dirt: 1. – Remove immediately: melting plastic, plastic foil, and food containing sugar. – Stop the appliance and let it cool down before you clean: limescale rings, water rings, fat stains, shiny metallic discolorations. Use a special cleaner applicable for surface of hob.
If there is a fault, first try to find a solution to the problem yourself. If you cannot find a solution to the problem yourself, speak your dealer or the local Service Force Centre. If you operated the appliance incorrectly, or the installation was not carried out by a 1 registered engineer, the visit from the customer service technician or dealer may not take place free of charge, even during the warranty period.
Electric supply: 230 V ~ 50 Hz 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse 3 By-pass diameters Burner Ø By-pass in 1/100 mm II2H3+ Auxiliary 28 G20 (2H) 20 mbar Semi-rapid 32 Triple Crown 56 Gas connection: G 1/2 " Category: Gas supply: Appliance class: Gas burners NORMAL POWER NORMAL POWER REDUCED POWER kW kW inj. 1/100 mm m³/h inj. 1/100 mm Auxiliary 1.0 0.33 70 0.095 50 73 71 Semi-rapid 2.0 0.45 96 0.
www.zanussi.
www.zanussi.
397225902-A-112012 www.zanussi.