GAS HOB ZGG 649 INSTRUCTION BOOKLET IL O
Important Safety Information You MUST read these warnings carefully before installing or using the appliance. Installation This appliance must be installed by qualified personnel, according to the manufacturer’s instructions and to the rules in force. Remove all packaging before using the appliance. Ensure that the gas and electrical supply complies with the type stated on the rating plate, located near the gas supply pipe. Do not attempt to modify the appliance in any way.
Contents For the User For the Installer Description of the Appliance Technical Data Page 6 Page 4 Installation Page 7 Operation Page 5 Gas Connection Page 7 Building In Page 8 Fitting the Hob to the Worktop Page 9 Electrical Connection Page 9 Commissioning Page 10 Servicing Page 11 Technical Maintenance Page 11 Maintenance and Cleaning Page 5 Something Not Working? Page 6 Guide to Use the instructions The following symbols will be found in the text to guide you througho
Description of the Appliance 3 5 1 6 7 8 4 2 1. 2. 3. 4. 5. 6. 7. 8. Hob Top Rapid Burner Semi-rapid Burners Auxiliary Burner Control knob for back right burner (semi-rapid) Control knob for back left burner (semi-rapid) Control knob for front left burner (rapid) Control knob for front right burner (auxiliary) INSTALLATION Any gas installation must be carried out by qualified personnel, and in accordance with existing rules and regulations.
Operation This hob is provided with a safety device, which will stop the gas flow if the flame accidentally goes off during cooking. To light a burner, turn the relevant control knob anticlockwise to maximum position and push it down to ignite. Keep the control knob pressed down for about 5 seconds, to allow the safety device to be switched off. Then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again.
Something Not Working? If the appliance is not working correctly, please carry out the following checks before contacting your local Service Centre. SYMPTOM SOLUTION There is no spark when lighting the gas Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the burner cap and crown have been replaced correctly, e.g. after cleaning.
Installation IMPORTANT This appliance must be installed by qualified personnel. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. Gas Connection On the end of the shaft (A) , which includes the GJ 1/2" threaded elbow, an adjustable joint is fixed so that the washer (B) is fitted between the components as shown in the diagram.
Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in diagram 1.
Fitting the hob to the worktop Before fitting the hob into the cut out, an adhesive seal must be fitted to the underside outside edge (see diagram) of the hob. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below. FO 2108 1) Remove the pan supports, the burners caps and crowns and turn the hob upside down, taking care the ignition candles are not damaged in this operation.
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: 10 Re-ignite the burner and set to MIN.
Servicing A: Removal Of Hob Top D: Removal Of Burner 1. Remove the panstands and each burner cap and crown. 2. Lift the hob from off the working top. 3. Remove the two self tapping screws from each burner and the two fixing screws on the right hand side of the hob. 1. Follow the procedures in Section A. 2. With the aid of a 12mm spanner loosen off the pipe connection nut. 3. From the underside of the hob remove 2 self tapping screws from the burner body. 4.
