GAS HOBS ZGF982C INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB
Important Safety Information You MUST read hese warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation l l l l l This hob must be installed by qualified personnel, according to the manufacturers instructions and to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. Remove all packaging before using the hob.
Contents For the Installer For the User Important Safety Information 2 Instructions for the Installer 9 Description of the Hob 3 Important safety requirements 10 Operation 4 Installation 10 Maintenance and Cleaning 4 Building In 11 Something Not Working? 5 Electrical connections 12 Guarantee Conditions 6 Wiring Diagram 13 Fault Finding 13 Commissioning 15 Conversion from Natural Gas to LPG 15 Description of the Hob 1 2 3 4 2 5 1. Auxiliary Burner 2.
Operation Hob burners F To light a burner: push in the relevant control knob and turn it anticlockwise to maximum position; l then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used (see table). l Burner Ultra-rapid (Double-crown) Large (rapid) Medium (semi-rapid) Small (Auxiliary) minimum diameter 180 mm. 180 mm. 120 mm.
Cast Iron Pan Supports YES The hob has cast iron pan supports. Take care when removing them. They are fair heavy and could damage the hob or your kitchen furniture if you let them fall down. To keep the pan supports in the correct position, they are hooked into hinges at the back of the hob. When removing the pan supports, lift them up as shown in the diagram. Never turn the pan supports on the hinges, this could damage them. Wash the pan supports using hot soapy water.
Service and Spare Parts Customer Care Department In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Zanussi Service Force Centre by telephoning: For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.zanussi.co.
ZANUSSI SERVICE FORCE To contact your local Zanussi Service Force Centre telephone 08705 929 929 CHANNEL ISLANDS GUERNSEY JERSEY Guernsey Electricity PO Box 4 Vale, Guernsey Channel Islands Jersey Electricity Company PO Box 45 Queens Road St Helier Jersey Channel Islands JE4 8NY ORKNEY (M65) Corsie Domestics 7 King Street Kirkwall Orkney KW15 PERTH Hydro Electrical Inveralmond House Ruthervenfield Road Perth PH1 3AQ PERTH (OWN SALES) SCOTLAND ABERDEEN (M05) AUCHTERMUCHY (M03) BLANTYRE (M07) 54 Cla
ZANUSSI SERVICE FORCE To contact your local Zanussi Service Force Centre telephone 08705 929 929 MIDLANDS BIRMINGHAM (M18) 66 Birch Road East Wyrley Road Ind. Estate Witton Birmingham B6 6DB BOURNE Manning Road Ind. Estate Pinfold Road Bourne PE10 9HT (M44) BRIDGNORTH (M72) 68 St. Marys Street Bridgnorth Shropshire WV16 4DR LONDON & EAST ANGLIA 11a Gardener Ind. Estate Kent House Lane Beckenham Kent BR3 1QZ CHELMSFORD (M47) Hanbury Road Widford Ind.
Instructions for the Installer Ignition HT Spark Spark Generator Engineers technical data OVERALL DIMENSIONS Width: Depth: Spark Gap 860 mm. 510 mm. Rear Left Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) CUT OUT DIMENSIONS Width: Depth: Front Left Burner (auxiliary) Heat Input 1.0 kW (3412 BTU/HR) 830 mm. 480 mm. Rear Right Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Front Right Burner (rapid) Heat Input 3.
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Part 2 and B.S. 6891 Current Editions. The hob should not be installed in a bed sitting room with a volume of less than 20 m3.
Cut Out Size Rectangular cut-out size for hob 30 480 55 m in. The dimensions of the cut-out are given in the diagram. 830 Building In FO 2349 Dimensions are given in mm. ON/OFF SWITCH Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in diagram 3.
Seal a FO 0199 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. The manufacturer declines any liability should these safety measures not be observed. Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm.
Wiring Diagram L A. IGNITOR SWITCH 1 A B. IGNITOR UNIT 2 0 3 220/240 4 5 6 B N Fault Finding Brown Blue Green Yellow Blue Brown PLUG (with cover removed) Earth Wire Green/Yellow START Isolate appliance and carry out: A: Earth Continuity check. Neutral Wire Blue SOCKET (face view) ( ) E( ) FUSE Preliminary Electrical Systems Check N L Green Yellow NO YES Carry out: C: Polarity check. Has inlet fuse blown? NO YES Inlet wiring faulty. Rectify any fault.
Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Light burner manually Check polarity and earth continuity of supply point Check by pass simmer adjusted Check position of the electrode Check earth continuity of appliance Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from 'L' on the mains connector block and the taps ignition switches Check continuity from igni
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: Re-ignite the burner and set to MIN. Remove the control knob.
Grafiche MDM - Forlì CUSTOMER CARE Zanussi 55-77 High Street Slough Berkshire, SL1 1DZ Tel: 08705 727727 © Electrolux Household Appliances Limited 2000 From the Electrolux Group. The worlds No.1 choice. The Electrolux Group is the worlds largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx.
