EN User manual Gas hob ZGF782IT GB
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Operation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 7 8 9 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11 Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 1
• • • • • • • • • • • • • • • damage to property caused by failure to obey these requirements. To prevent the risks of structural damage or physical injury, installation, connection of the appliance to the power supply and gas system, setting up and maintenance must only be done by qualified personnel in compliance with standards and local regulation force. Make sure that the appliance is not damaged because of transport. Do not connect a damaged appliance.
Installation Warning! The following instructions about installation, connection and maintenance must be carried out by qualified personnel in compliance with standards and local regulations in force. Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S.
squeezed. Also be careful when the hob is put together with an oven. 1 Important! It is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. Important! Failure to ensure the correct assembly will cause leakage of gas. Important! Make sure that the gas supply pressure of the appliance obeys the recommended values. Rigid connection: Carry out connection by using metal rigid pipes (copper with mechanical end). Injectors replacement 1. 2. 3.
1. Electrical Requirements Any permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician, e.g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). The manufacturer declines any liability should these safety measures not be observed.
A a) Removable panel b) Space for connections Kitchen unit with oven The hob recess dimensions must obey the indication and the kitchen unit must be equipped with vents to let a continuous supply of air. The electrical connection of the hob and the oven must be installed separately for safety reasons and to let easy remove oven from the unit.
Symbol Description minimum gas supply Operation Ignition of the burner Warning! Be very careful when you use open fire in kitchen environment. Manufacturer decline any responsibility in case misuse of the flame 1 2 Always light the burner before you put cookware. 3 To light the burner: 1. Turn the control knob counterclockwise to the maxi) and push it down. mum position ( 2. Keep the control knob pushed for approximately 5 seconds; this will let thermocouple to warm up.
If the burner accidentally goes out, turn the control knob to the off position and try to light the burner again after minimum 1 minute. The spark generator can start automatically when you switch on the mains, after installation or a power cut. It is normal. Turning the burner off To put the flame out, turn the knob to the symbol . Warning! Always turn the flame down or switch it off before you remove the pans of the burner.
• To make the burners work correctly, make sure that the arms of the pan supports are in the centre of the burner. 2. 3. – Stop the appliance and let it cool down before you clean: limescale rings, water rings, fat stains, shiny metallic discolorations. Use a special cleaner applicable for surface of hob. Clean the appliance with a damp cloth and some detergent. At the end rub the appliance dry with a clean cloth.
Labels supplied with the accessories bag Stick the adhesive labels as indicated below: 1 2 3 MOD. MOD. PROD.NO. PROD.NO. SER.NO SER.NO 03 IT DATA DATA MADE IN ITALY MODEL 0049 MOD. PROD.NO. SER.NO. TYPE 230V-50Hz IP20 MODEL 1 Stick it on Guarantee Card and send this part 2 Stick it on Guarantee Card and keep this part 3 Stick it on instruction booklet These data are necessary to help you quickly and correctly. These data are available on the supplied rating plate. • Model description .....
By-pass diameters Burner Ø By-pass in 1/100 mm Burner Ø By-pass in 1/100 mm Rapid 42 Auxiliary 28 Triple Crown 56 Semi-rapid 32 Gas burners NORMAL POWER NORMAL POWER REDUCED POWER NATURAL GAS G20 (2H) 20 mbar BURNER kW Auxiliary Semi-rapid kW inj. 1/100 mm m³/h LPG (Butane/Propane) G30/G31 (3+) 28-30/37 mbar inj. 1/100 mm G30 28–30 mbar G31 37 mbar g/h g/h 1.0 0.33 70 0.095 50 73 71 2.0 0.45 96 0.190 71 145 143 Rapid 3.0 (natural gas) 2.8 (LPG) 0.75 119 0.
358221823-A-182011 www.zanussi.
