GAS HOB ZGF782C INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB
Important Safety Information You MUST read hese warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation l l l l l This hob must be installed by qualified personnel, according to the manufacturers instructions and to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. Remove all packaging before using the hob.
Contents For the Installer For the User Important Safety Information 2 Instructions for the Installer 7 Description of the Hob 3 Important safety requirements 8 Operation 4 Installation 9 Maintenance and Cleaning 4 Building In 10 Something Not Working? 5 Electrical connections 11 Guarantee Conditions 6 Wiring Diagram 12 Fault Finding 12 Commissioning 14 Conversion from Natural Gas to LPG 14 Description of the Hob 2 1 3 2 5 4 1. Auxiliary Burner 2. Semi-rapid Burners 3.
Operation Hob burners F To light a burner: push in the relevant control knob and turn it anticlockwise to maximum position; l then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used (see table). l Burner Ultra-rapid (Triple-crown) Large (rapid) Medium (semi-rapid) Small (Auxiliary) minimum diameter 180 mm. 180 mm. 120 mm.
YES Cast Iron Pan Supports The hob has cast iron pan supports. Take care when removing them. They are fair heavy and could damage the hob or your kitchen furniture if you let them fall down. To keep the pan supports in the correct position, they are hooked into hinges at the back of the hob. When removing the pan supports, lift them up as shown in the diagram. Never turn the pan supports on the hinges, this could damage them. Wash the pan supports using hot soapy water.
Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Zanussi Service Force Centre by telephoning: 0870 5 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.
Instructions for the Installer Ignition HT Spark Spark Generator Engineers technical data OVERALL DIMENSIONS Width: Depth: Spark Gap 680 mm. 510 mm. Rear Left Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) CUT OUT DIMENSIONS Width: Depth: Front Left Burner (auxiliary) Heat Input 1.0 kW (3413 BTU/HR) 560 mm. 480 mm. Rear Right Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) SUPPLY CONNECTIONS Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Front Right Burner (rapid) Heat Input 3.
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Part 2 and B.S. 6891 Current Editions. The hob should not be installed in a bed sitting room with a volume of less than 20 m3.
Installation IMPORTANT: This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory.
Building In Building over a cupboard or drawer Building over a kitchen unit with door If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2.
Seal a FO 0199 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. The manufacturer declines any liability should these safety measures not be observed. Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm.
Wiring Diagram L A. IGNITOR SWITCH 1 A B. IGNITOR UNIT 2 0 3 220/240 4 5 6 B N Fault Finding Brown Blue Green Yellow Blue Brown Earth Wire Green/Yellow START Isolate appliance and carry out: A: Earth Continuity check. Neutral Wire Blue SOCKET (face view) ( ) E( ) N L Green Yellow NO YES Carry out: C: Polarity check. Has inlet fuse blown? NO YES Inlet wiring faulty. Rectify any fault. Isolate appliance and carry out: B: Insulation check.
Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Light burner manually Check polarity and earth continuity of supply point Check by pass simmer adjusted Check position of the electrode Check earth continuity of appliance Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from 'L' on the mains connector block and the taps ignition switches Check continuity from igni
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: Re-ignite the burner and set to MIN. Remove the control knob.
Grafiche MDM - Forlì CUSTOMER CARE Zanussi 55-77 High Street Slough Berkshire, SL1 1DZ Tel: 08705 727727 © Electrolux plc 2003 From the Electrolux Group. The worlds No.1 choice. The Electrolux Group is the worlds largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx.