Instruction booklet Gas hob ZGF 642 ZGF 692 C ZGF 692 CT GB
Welcome to the world of Electrolux Thank you for choosing a first class product from Electrolux, which hopefully will provide you with lots of pleasure in the future. The Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable. You find some examples on the cover in this manual. Please take a few minutes to study this manual so that you can take advantage of the benefits of your new machine.
Contents Important Safety Information ......................................................... 4 Description of the Hobs ......................................................................... 6 Instructions for the User ................................................................. 7 Operation .............................................................................................. 8 Maintenance and Cleaning .................................................................
Important Safety Information You MUST rread ead these war nings car efully befor e installing or carefully before using the hob. If you need assistance, contact our Customer Care Department on 08705 727 727. I nstallation # # # # # This appliance must be installed and serviced by a competent person as stated in the Gas Safety (Installation and Use) Regulations Current Editions and the IEE Wiring Regulations.
# # # # # # # # # When using the hob for a long period time, the ventilation should be improved, by opening a window or increasing the extractor speed. Do not use this hob if it is in contact with water. Do not operate the hob with wet hands. Ensure the control knobs are in the ‘OFF’ position when not in use. When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance.
Description of the Hobs Model ZGF 642 3 2 3 1 4 6 2 3 Model ZGF 692 CZGF 692 CT 3 1 5 6 1. 2. 3. 4. 5. 6.
Instructions for the User INSTALLATION Any gas installation must be carried out by a registered competent person, and in accordance with existing rules and regulations. The relevant instructions are to be found in the second section of this manual. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown.
When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated automatically. In the absence of electricity electricity, ignition can occur without the electrical device; in this case, approach the burner with a flame, push the relevant knob down and turn it anti-clockwise until it reaches the maximum position. If the control knobs become difficult to turn, please contact your local Service Force Centre.
As soon as a liquid starts boiling, turn down the flame so that it will barely keep the liquid simmering. Use only pans or pots with flat bottom. If you use a saucepan which is smaller than the recommended size, the flame will spread beyond the bottom of the vessel, causing the handle to overheat. Carefully supervise cooking with fat or oil oil, since these types of foodstuff can result in a fire, if over-heated. The stainless steel can become tarnished if excessively heated.
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob fr om the electricity supply from supply.. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. This appliance cannot be cleaned with steam or with a steam cleaning machine. The Hob T op Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing up liquid has been added.
Take car e when rremoving emoving them. care They are heavy and could damage the hob or your kitchen furniture if you let them fall. Never turn the cast iron pan supports on the hinges, this could damage them. To remove the cast iron pan supports completely, proceed as shown in Fig. 2. Wash the pan supports using hot soapy Fig. 3 water. If necessary, a paste cleaner or a soap impregnated steel wool pad can be used with caution.
Something Not W orking? Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM $ There is no spark when lighting the gas. SOLUTION % % % % $ The gas ring burns unevenly. % % Check that the unit is plugged in and the electrical supply is switched on. Check that the RCCB has not tripped (if fitted). Check the mains fuse has not blown. Check the burner cap and crown have been replaced correctly, e.g.
Instructions for the Installer Engineer technical data OVERALL DIMENSIONS Width: Depth: 580 mm 510 mm CUT OUT DIMENSIONS Width: Depth: Thickness: 560 mm 480 mm 30 mm SUPPL Y CONNECTIONS SUPPLY Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V~ 50 Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse HEA T INPUT HEAT Rear Left Burner 2.0 kW (6826 BTU/HR) (semi-rapid) Front Right Burner 3.0 kW Natural Gas (10239 BTU/HR) (Mod. ZGF 642) 2.8 kW L.
BURNER RAPID POSITION M A X MIN SEMI-RAPID A U X I L I A R Y TRIPLECROWN TYPE OF GAS NATURAL GAS 20 mbar VALUE = 37.78 MJ/m 3 Ws - 50.7 MJ/ m3 LPG GAS 28-30/37 mbar VALUE = 49.92 MJ/Kg NOMINALTHERMAL POWER kW MIN 1.0 0.33 4.0 1.2 0.286 0.057 0.190 0.038 0.095 0.028 0.381 0.114 119 Adjust. 96 Adjust. 70 Adjust. 146 Adjust. NOMINALTHERMAL POWER kW 2.8 0.65 2.0 0.45 1.0 0.33 4.0 1.2 NOMINALFLOW RATE g/h 202 4 3.
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. 813 Current Editions and the ETCI Rules for Electrical Installations.
Installation IMPOR TANT This hob must be installed by a competent person to the relevant Gas Standards. Any gas installation must be carried out by a registered competent person. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this instruction booklet be ignored.
Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Ensure that the main connection pipe does not exert any strain on the hob.
Location The hob may be located in a kitchen, a kitchen/diner or bed sitting room, but not in a bathroom, shower room or garage. Ensure that there is a minimum distance of 55 mm between the rear cut out edge and the wall. A minimum distance of 100 mm must be left between the side edges of the cut out and any adjacent cabinets or walls. The minimum distance combustible material can be fitted above the hob in line with the edges of the hob is 400 mm.
Fitting the Hob into the Worktop Carry out the building in of the hob as follows: 1. place the seals supplied with the hob on the side edges of the cut out and at 8 mm. from the front and rear edges, as shown in the diagram, taking care that the seals meet without overlapping; 2. place the hob in the cut out, taking care that it is centred; 3. fix the hob with the relevant fixing clamps and screws, as shown in the diagram. When the screws have been tightened, the excess seal can be removed.
Building In B uilding over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2.
Electrical Connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. Electrical Requirements Any permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician, e.g.
3) Connect the brown (live) wire to the terminal in the plug which is marked with the letter 'L' or coloured red. Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath. A cut off plug inserted into safety (shock) hazard. Ensure of safely safely..
Fault Finding Preliminary Electrical Systems Check Blue Brown START Isolate appliance and carry out: A: Earth Continuity check. YES NO Blue Green Yellow Brown Carry out: C: Polarity check. Carry out: D: Resistance to Earth check. Has inlet fuse blown? Electricity supply should now be satisfactory. YES NO PLUG (with cover removed) Earth Wire Green/Yellow Neutral Wire Blue SOCKET (face view) ( ) E( ) FUSE Inlet wiring faulty. Rectify any fault.
A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on W (Ohms) x 1 scale and adjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 W (Ohm), check all earth wires for continuity and all contacts clean and tight. B. INSULA TION CHECK INSULATION Appliance electrically disconnected, all switches ON. a) meter set on W (Ohms) x 1 scale. Test leads from L to N in appliance terminal block.
Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from 'L' on the mains connector block and the taps ignition switches Check continuity from ignition switches connector to ignitor unit Light burner manually Check by pass simmer adj
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. the gas tap to the MAX position and ignite. ! 1)2) Turn Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: the burner and set ! 1) Re-ignite to MIN. 2) Remove the control knob.
Conversion from Natural Gas to LPG IMPOR TANT The replacement/conversion from natural gas to LPG should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted. The gas rate is adjusted to suit.
Guarantee/Customer Service Standard guarantee conditions We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: · The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning 0870 5 929 929 Your telephone call will be automatically routed to the Service Force Centre covering your postcode area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www .servicefor ce.co.uk www.servicefor .serviceforce.co.
European Guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law.
www.zanussi-electrolux.co.uk 35670-9509 04/07 R.
