EN User manual Hob ZEE6940 GB
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Product description _ _ _ _ _ _ _ _ _ _ _ _ _ Operation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 7 7 7 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8 What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Environment concerns _ _ _ _ _ _ _ _ _ _ _ 10 Subject to change without notice.
• Use the correct mains connection cable and replace the damaged mains cable with proper special cable. Speak your local Service Force Centre. • The appliance must have the electrical installation which lets you disconnect the appliance from the mains at all poles with a contact opening width of minimum 3 millimetres. • If the fixing bracket is near to the terminal block, always make sure the connection cable does not come in contact with the edge of the bracket.
• Do not let cookware boil dry in order to prevent damage to the cookware and hotplate. • Do not use the solid hotplate with empty cookware or without cookware. • Do not put aluminium foil on parts of the appliance. – Disconnect the appliance from the power supply. – Cut off the mains cable where it connects with the appliance and discard it. – Speak to your local authorised facilities for disposal of your appliance.
Warning! Risk of injury from electrical current. Carefully obey the instructions for electrical connections. • The electrical mains terminal is live. • Make the electrical mains terminal free of voltage. • Install correctly to give anti-shock protection. • Loose and incorrect mains plug and socket connections can make the terminal become too hot. • A qualified electrician must install the clamping connections correctly. • Use a strain relief clamp on cable.
3. Connect the brown (live) wire to the terminal in the plug which is marked with the letter 'L' or coloured red. There must be no cut or stray strands of wire present. The cord clamp must be correctly attached on the outer sheath. Warning! Make sure that the cut off plug is disposed of safely. A cut off plug put into a 13 amp socket is a safety hazard. There is a risk of electrical shock.
Product description Cooking surface layout 1 2 180 180 mm 6 145 mm 5 mm 1 Single cooking zone 2000 W 2 Single cooking zone 2000 W 145 3 Single cooking zone 1500 W 4 Control knobs 3 mm 5 Power indicator 6 Single cooking zone 1500 W 4 Electric cooking zones control knobs Symbol Function Symbol Function 1 minimum heat 0 off position 6 maximum heat Operation To switch on and increase the heat setting turn the knob counterclockwise. To decrease the heat setting turn the knob clockwise.
• Stop the solid hotplate before the end of the cooking time to use residual heat. • For satisfactory results, the bottom of pans must have the same dimensions (or slightly larger) as solid hotplates. Do not use smaller pans.
Problem Possible cause and remedy The cooking zone does not heat up. • Make sure that the appliance is plugged in and the electrical supply is switched on. • Make sure that you turn the correct control knob. • Examine the fuse in the electrical system of the house in the fuse box. If the fuses blow time after time, speak to an authorised electrician. The effectiveness of the hob is not satisfactory. • • • • Make sure that the hob is clean and dry.
Technical data Hob dimensions Front left cooking zone 145 mm 1.5 kW Front right cooking zone 145 mm 1.5 kW Hob recess dimensions Rear left cooking zone 180 mm 2.0 kW Width: 560 mm 2.0 kW Length: 480 mm Rear right cooking zone 180 mm Width: 594 mm Length: 510 mm Total rating Hot plate rating Electric supply 7.0 kW 230 V ~ 50 Hz Environment concerns The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
www.zanussi.
397233803-D-122012 www.zanussi.
