User manual Dishwasher ZDTS102
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Washing programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Use of the appliance _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Set the water softener _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Use of dishwasher salt _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Use of rinse aid _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Load cutlery and dishes _ _ _ _ _ _ _ _ _ _ _ _ _ _ Use of detergent _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 3 4 5 6 7 7 8 9 Select and
• A qualified and competent person must do the electrical installation. • A qualified and competent person must do the plumbing installation. • Do not change the specifications or modify this product. Risk of injury and damage to the appliance. • Do not use the appliance: – if the mains cable or water hoses are damaged, – if the control panel, worktop or plinth area are damaged, that you can get access to the inner side of the appliance. Contact your local Service Force Centre.
Programme selection/cancel button • Deactivation/activation of the audible signals. Use the programme selection/cancel button for these operations: • To set the washing programme. Refer to the chapter 'Setting and starting a washing programme'. • To set the water softener. Refer to the chapter 'Setting the water softener'. • To deactivate/activate the audible signals. Refer to the section 'Audible signals'. • To cancel a washing programme in progress.
Programme Degree of soil Normal soil 1) 2) Type of load Programme description Prewash Crockery, Main wash up to 65°C cutlery, pots 2 intermediate rinses and pans Final rinse Drying Crockery and cutlery Main wash up to 65°C Final rinse Normal soil Crockery and cutlery Prewash Main wash up to 50°C 1 intermediate rinse Final rinse Drying Any Partial load (to be completed later in the day) Normal or light soil 1 cold rinse (to prevent food scraps to bond).
7. Start the washing programme. 'Use of detergent'. If you use detergent tablets, refer to the chapter Set the water softener The water softener removes minerals and salts from the water supply. Minerals and salts can have bad effect on the operation of the appliance. Water hardness is measured in equivalent scales: • German degrees (dH°). • French degrees (°TH). • mmol/l (millimol per litre - international unit for the hardness of water). • Clarke.
3. Press and hold the programme selection/cancel button. 4. Release the programme selection/cancel button when programme indicator light A starts to flash and programme indicator light B comes on. 5. Wait until programme indicator light B goes off. – Programme indicator light A starts to flash. – The end indicator light starts to flash. 6. Press the programme selection/cancel button one time. – Programme indicator light A starts to flash. – The setting function of the water softener is activated.
Fill when the rinse aid indicator (B) becomes clear. 2 1 5 Caution! Do not fill the rinse aid dispenser with other products (e.g. dishwasher cleaning agent, liquid detergent). There is a risk of damage to the appliance. Adjusting the dosage of rinse aid 4 3 The rinse aid dial is set at the factory at position 4. To increase or decrease the dosage refer to 'What to do if...
Adjustment of the height of the upper basket If you put large plates in the lower basket, first move the upper basket to a upper position. Warning! Adjust the height before you load the upper basket. Maximum height of the dishes in : 1 Arrange service dishes and large lids around the edge of the lower basket. 2 2 1 Use the cutlery grid. If the dimensions of the cutlery prevent use of the grid, remove it.
1 2 5 6 Use of detergent tablets 3 Fill the detergent dispenser (A) with detergent. 4 If you use a washing programme with prewash phase, put more detergent in the prewash detergent compartment (B). Put the detergent tablet in the detergent dispenser (A). Detergent tablets contain: • detergent • rinse aid • other cleaning agents. Do these steps to use detergent tablets: 1. Make sure that the detergent tablets are applicable for your water hardness. Refer to the instructions from the manufacturer. 2.
Select and start a washing programme Set the washing programme with the door ajar. The washing programme only starts after you close the door. Until then it is possible to modify the settings. 1. Switch off the appliance. 2. Set a new washing programme. Fill the detergent dispenser with detergent before you set a new washing programme. Do these steps to set and start a washing programme: 1. Switch on the appliance. 2. Make sure that the appliance is in setting mode. 3.
1 2 Fully clean the filters A, B and C below running water. 5 Put the filter system in position. To lock the filter system, turn the handle clockwise until it locks in position. Important! Do not remove the spray arms. If the holes in the spray arms become clogged, remove remaining parts of soil with a cocktail stick. External cleaning 3 To remove filters B and C, turn the handle approximately 1/4 anticlockwise. 4 Remove the flat filter A from the bottom of the appliance.
Fault code and malfunction Possible cause and solution • continuous flash of the light of the running programme • intermittent audible signal • 1 flash of the end indicator light The appliance does not fill with water . • The water tap is blocked or furred with limescale. Clean the water tap. • The water tap is closed. Open the water tap. • The filter in the water inlet hose is blocked. Clean the filter. • The connection of the water inlet hose is not correct. The hose can be kinked or squashed.
The cleaning results are not satisfactory Limescales particles on the dishes • The salt container is empty. • The water softener is adjusted on a wrong level. • The salt container cap is not closed correctly. The dishes are wet and dull • No rinse aid has been used. • The rinse aid dispenser is empty. There are streaks, milky spots or • Decrease the rinse aid dosage. a bluish coating on glasses and dishes Dry water drop signs on glasses • Increase rinse aid dosage.
Important! Obey the instructions in the enclosed template to: • Build-in the appliance. • Install the furniture panel. • cConnect to the water supply and drain. Install the appliance under a counter (kitchen worktop or sink). If a repair is necessary, the appliance must be easily accessible for the engineer. Put the appliance adjacent to a water tap and a drain. For the venting of the dishwasher only water fill, water drain and power supply cable openings are necessary.
Drain hose max 400 cm max 85 cm min 40 cm 3 1 Connect the water drain hose to the sink spigot. 2 4 The internal diameter must not be smaller than the diameter of the hose. If you connect the water drain hose to a trap spigot under the sink, remove the plastic membrane (A). If you do not remove the membrane, remaining food can cause a blockage in the drain hose spigot. Caution! Make sure that the water couplings are tight to prevent water leakage.
www.electrolux.
