EN User manual Dishwasher ZDTS 102 2
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Washing programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Use of the appliance _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Setting the water softener _ _ _ _ _ _ _ _ _ _ _ _ _ Use of dishwasher salt _ _ _ _ _ _ _ _ _ _ _ _ _ _ Use of rinse aid _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Loading cutlery and dishes _ _ _ _ _ _ _ _ _ _ _ _ Use of detergent _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 3 4 5 6 7 7 8 9 Setting and starting
• Do not change the specifications or modify this product. Risk of injury and damage to the appliance. • Do not use the appliance: – if the mains cable or water hoses are damaged, – if the control panel, worktop or plinth area are damaged, that you can get access to the inner side of the appliance. Contact your local Service Force Centre. • Do not drill into the sides of the appliance to prevent damage to hydraulic and electrical components.
• To set the water softener. Refer to the chapter 'Setting the water softener'. • To deactivate/activate the audible signals. Refer to the section 'Audible signals'. • To cancel a washing programme in progress. Refer to the chapter 'Setting and starting a washing programme'. Setting mode The appliance is in setting mode when all the programme indicator lights are off and the end-of-programme indicator light flashes. The appliance must be in setting mode for these operations: – To set a washing programme.
Programme Degree of soil Type of load Programme description Quick 65° A 30'1) Normal or light soil Crockery and cutlery Main wash up to 65°C Final rinse Eco 50°2) Normal soil Crockery and cutlery Prewash Main wash up to 50°C 1 intermediate rinse Final rinse Drying Prewash Any Partial load (to be 1 cold rinse (to prevent food scraps to completed later in the bond). day). Detergent is not necessary with this programme. 1) This is the perfect daily programme to clean a not fully load.
Setting the water softener The water softener removes minerals and salts from the water supply. Minerals and salts can have bad effect on the operation of the appliance. Water hardness is measured in equivalent scales: • German degrees (dH°). • French degrees (°TH). • mmol/l (millimol per litre - international unit for the hardness of water). • Clarke. Adjust the water softener to the water hardness in your area. If necessary, contact your local water authority.
. Press the programme selection/cancel button one time to increase the water softener level by one step. 8. Press the on/off button to save the operation. Use of dishwasher salt Caution! Only use dishwashers salt. Types of salt that are not applicable for dishwashers cause damage to the water softener. 5 1 6 It is normal that water overflows from the salt container when you fill it with salt. 2 Make sure that there is no grain of salt outer of the salt compartment.
Fill when the rinse aid indicator (B) becomes clear. Adjusting the dosage of rinse aid The rinse aid dial is set at the factory at position 4. To increase or decrease the dosage refer to 'What to do if...' 5 Caution! Do not fill the rinse aid dispenser with other products (e.g. dishwasher cleaning agent, liquid detergent). There is a risk of damage to the appliance.
1 Arrange the items to let water touch all surfaces. 2 For longer items, fold the cup racks up. Adjustment of the height of the upper basket If you put large plates in the lower basket, first move the upper basket to a upper position. Warning! Adjust the height before you load the upper basket. Maximum height of the dishes in : upper basket lower basket Upper position 20 cm 31 cm Lower position 24 cm 27 cm 1 2 Do these steps to move the upper basket to the upper or lower position: 1.
tainers. In this condition the rinse aid indicator light stays on when the appliance is switched on. 1. Do a check if these tablets are applicable for the local water hardness. Refer to the instructions from the manufacturer. 2. Select the lowest setting for the water hardness and rinse aid dosage. 5 6 Different brands of detergent dissolve in different times. Some detergent tablets do not have the best cleaning results during short washing programmes.
• The appliance stops automatically. • The audible signal for the end of the programme operates. 1. Open the door. – The end-of-programme indicator light comes on. – The programme indicator light stays on. 2. Press the on/off button. 3. For better drying results, keep the door ajar for some minutes before you remove the dishes. Let the dishes cool down before you remove them from the appliance. Hot dishes are easily damaged.
What to do if… The appliance does not start or stops during operation. If there is a fault, first try to find a solution to the problem yourself. If you cannot find a solution to the problem yourself, contact the Service Force Centre. Caution! Switch off the appliance before you do the below suggested corrective actions.
The cleaning results are not satisfactory The dishes are not clean • The selected washing programme is not applicable for the type of load and soil. • The baskets are loaded incorrectly so that water cannot reach all surfaces. • Spray arms do not turn freely because of incorrect arrangement of the load. • The filters are dirty or not correctly installed. • The quantity of detergent is too little or missing. Limescales particles on the dishes • The salt container is empty.
Warning! To discard the appliance, follow the procedure: • Pull the mains plug out of the socket. • Cut off the mains cable and mains plug and discard them. • Discard the door catch. This prevents the children to close themselves inside the appliance and endanger their lives. Installation Warning! Make sure that mains plug is disconnected from the mains socket during installation. Important! Obey the instructions in the enclosed template to: • Build-in the appliance. • Install the furniture panel.
• Do not put the water inlet hose or the safety valve in water. • If the water inlet hose or the safety valve is damaged, immediately disconnect the mains plug from the mains socket. • Only let the Service Force Centre replace the water inlet hose with safety valve. Drain hose 3 max 400 cm max 85 cm min 40 cm 1 Connect the water drain hose to the sink spigot. 2 4 The internal diameter must not be smaller than the diameter of the hose.
www.zanussi.com 117950480 - 00 - 072009 To buy accessories, consumables and spare parts at our online shop please visit: www.zanussi.co.
