User Manual GETTING STARTED? EASY.
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
• • • • • • Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance.
WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. USE • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is complete.
EASY START 2 1 3 4 5 6 7 1 On/off button 2 Display 6 XtraDry button 7 Delay button 3 Programme button (up) 4 Programme button (down) 8 CANCEL button 9 Indicators 9 8 5 TimeManager button INDICATORS End indicator. Salt indicator. It is always off while the programme operates. Rinse aid indicator. It is always off while the programme operates. BEAM-ON-FLOOR The Beam-on-Floor is a light that shows on the kitchen floor below the appliance door.
Consumption values 1) Programme P2 AUTOMATIC3) Degree of soil Type of load All Crockery, cutlery, pots and pans Programme phases Duration (min) Energy (kWh) Water (l) 45 - 160 0.7 - 1.5 7 - 12 • • Pre-wash Wash from 45 °C to 70 °C Rinses Dry • • P3 Intensive Heavy soil Crockery, cutlery, pots and pans • • • • Pre-wash Wash 70 °C Rinses Dry 140 160 1.4 - 1.6 13-15 P4 Quick 30Min4) Fresh soil Crockery and cutlery • 30 0.
ADJUSTING THE WATER SOFTENER Make sure the appliance is in user mode. • • Stop the countdown of Delay option. Bring the appliance back to the programme selection mode. To CANCEL: Press and hold CANCEL until the control panel indicates the appliance is in the programme selection mode. 1. Press USER MODE Settings available in the user mode: • The level of the water softener according to the water hardness. • Activation or deactivation of the rinse aid empty notification.
DEACTIVATING THE RINSE AID EMPTY NOTIFICATION Make sure the appliance is in user mode. 1. Press . • The indicators • • The indicator still flashes. The display shows the current setting: , and are off. – = rinse aid empty notification activated. – = rinse aid empty notification deactivated. 2. Press to change the setting. 3. Press the on/off button to confirm the setting. HOW TO DEACTIVATE AIRDRY AirDry improves the drying results with less energy consumption. to change the setting. 2.
The salt is used to recharge the resin in the water softener and to assure good washing results in daily use. Adding salt Before the first use, put one litre of water in the salt container. CAUTION! Water and salt can come out of the salt container during filling. To prevent corrosion, start a programme immediately after filling the salt container. ADDING RINSE AID 1 43 21 2 The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot rinse phase.
ADDING DETERGENT 1 A B 30 20 2 If the programme has a prewash phase, put a small quantity of detergent also in compartment B. ADDING MULTI-TABLETS 1 30 20 2 • Adjust the water softener to the lowest level. SETTING AND STARTING A PROGRAMME The AUTO OFF function This function decreases energy consumption by deactivating automatically the appliance when it is not operating. The function comes into operation: • 5 minutes after the completion of the programme.
If the option is not applicable to the programme, the related indicator does not turn on or it flashes quickly for a few seconds and then turns off. Opening the door while the appliance operates Opening the door while a programme is running stops the appliance. It may affect the energy consumption and the programme duration. After closing the door, the appliance continues from the point of interruption.
WHAT TO DO IF YOU WANT TO STOP USING MULTI-TABLETS Before you start to use separately detergent, salt and rinse aid do the following procedure. 1. Set the highest level of the water softener. 2. Make sure that the salt and rinse aid containers are full. 3. Start the shortest programme with a rinsing phase. Do not add detergent and do not load the baskets. 4. When the programme is completed, adjust the water softener according to the water hardness in your area. 5. Adjust the released quantity of rinse aid.
C • • • • Make sure that there are no residues of food or soil in or around the edge of the sump. Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides. Reassemble the filters (A) and (B). Put back the filter (A) in the flat filter (C). Turn it clockwise until it locks. An incorrect position of the filters can cause bad washing results and damage to the appliance CLEANING THE SPRAY ARMS Do not remove the spray arms.
Problem and alarm code The program does not start. Possible cause and solution • • • The appliance does not fill with water. • • • Make sure that the water tap is open. Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. Make sure that the water tap is not clogged. Make sure that the filter in the inlet hose is not clogged. Make sure that the inlet hose has no kinks or bends. • • • • Make sure that the sink spigot is not clogged.
For alarm codes not described in the table, contact an Authorised Service Centre. Refer to "Before first use", "Daily use", or "Hints and tips" for other possible causes. Once you have checked the appliance, deactivate and activate the appliance. If the problem occurs again, contact an Authorised Service Centre. THE WASHING AND DRYING RESULTS ARE NOT SATISFACTORY Problem Poor washing results. Possible cause and solution • • • Poor drying results.
Problem Possible cause and solution There are residues of detergent in the dispenser at the end of the programme. • • • The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water. Water cannot wash away the detergent from the dispenser. Make sure that the spray arm is not blocked or clogged. Make sure that items in the baskets do not impede the lid of the detergent dispenser from opening. Odours inside the appliance. • Refer to "Internal cleaning".
RATING PLATE INFORMATION FOR TEST INSTITUTES For all the necessary information for test performance, send an email to: info.test@dishwasher-production.com Write down the product number (PNC) that is on the rating plate. Mod. ... ... ... Prod. No. ... ... ... Ser. No. ... ENVIRONMENTAL CONCERNS the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office. Recycle the materials with the symbol .
156915480-A-092017 WWW.ZANUSSI.