User Manual GETTING STARTED? EASY.
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
• • • • • Do not keep the appliance door open without supervision to prevent to fall on it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet. The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused.
• • • • Do not drink and play with the water in the appliance. Do not remove the dishes from the appliance until the programme is completed. There can be detergent on the dishes. The appliance can release hot steam if you open the door while a programme operates. Do not put flammable products or items that are wet with flammable products in, near or on the appliance. SERVICE • Contact the Authorised Service Centre to repair the appliance. We recommend only the use of original spare parts.
EASY START 2 1 3 4 5 6 7 1 On/off button 2 Display 6 XtraDry button 7 Delay button 3 Programme button (up) 4 Programme button (down) 8 Cancel button 9 Indicators 9 8 5 Half load button INDICATORS End indicator. Salt indicator. It is always off while the programme operates. Rinse aid indicator. It is always off while the programme operates.
Consumption values 1) Programme Degree of soil Type of load Programme phases Duration (min) P4 Quick A30 Min5) Fresh soil Crockery and cutlery • P5 Delicate Energy (kWh) Water (l) 30 0.9 9 • Wash 60 °C or 65 °C Rinses Normal or light soil Delicate crockery and glassware • • • Wash 45 °C Rinses Dry 70 - 80 0.7 - 0.9 13 - 14 P6 Rinse and Hold 6) All • Prewash 14 0.1 4 P7 Plate Warmer 7) All • Rinse 70 °C 30 0.
When the appliance is in Programme selection mode it is possible to set a programme. If the control panel does not show this condition, do the Cancel. CANCEL FUNCTION Press and hold Cancel until the appliance is in programme selection mode. With this function you can cancel the running programme or the delay start. USER MODE While the appliance is in programme selection mode: 1. Press and hold and . • The indicators , and starts to flash.
• The indicator • The display shows the current setting: e.g. continues to flash. = level 5. to change the setting. Each time you press the button, the level increases. After level 10 you 2. Press will start again from level 1. 3. Press the on/off button to confirm the setting. If you use multi-tablets containing salt and the hardness of your water is lower than 21°dH, you can set the lowest water softener level. It deactivates the salt refill indicator.
– = rinse aid empty notification activated. – = rinse aid empty notification deactivated. 2. Press to change the setting. 3. Press on/off button to confirm the setting. When rinse aid chamber is empty, the rinse aid indicator is turned on notifying to refill rinse aid. If you are using multitabs containing rinse aid and you are satisfied with the drying result, you can deactivate the notification for refilling rinse aid. However, we recommend that you always use rinse aid for best drying performance.
ADDING SALT Before first use put one litre of water in the salt container. Water and salt can come out from the salt container when you fill it. Risk of corrosion. To prevent it, after you fill the salt container, start a programme. ADDING RINSE AID 1 43 21 2 The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot rinse phase. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance.
ADDING MULTI-TABLETS 1 30 20 2 • Adjust the water softener to the lowest level. THE AUTO OFF FUNCTION This function decreases energy consumption by deactivating automatically the appliance when it is not operating. The function comes into operation: • 5 minutes after the completion of the programme. • After 5 minutes if the programme has not started. STARTING A PROGRAMME 1. Keep the appliance door ajar. 2. Press the on/off button to activate the appliance.
OPTION XTRADRY Activate this option when you want to boost the drying performance. With the use of this option, the duration of some programmes, water consumption and the last rinse temperature can be affected. TheXtraDry option is not a permanent option and must be selected at every cycle. This option in not applicable to Rinse and Hold . OPTION DELAY max. 1. Press Delay until the display shows the delay time you want to set. 2. Close the appliance door, the countdown starts.
If you open the door before the activation of Auto Off, the appliance is automatically deactivated. HINTS AND TIPS GENERAL The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • Remove larger residues of food from the dishes into the waste bin. • Do not pre-rinse dishes by hand. When needed, use the prewash programme (if available) or select a programme with a prewash phase. • Always use the whole space of the baskets.
BEFORE STARTING A PROGRAMME Make sure that: • The filters are clean and correctly installed. • The cap of the salt container is tight. • The spray arms are not clogged. • There is dishwasher salt and rinse aid (unless you use multi- tablets). • The position of the items in the baskets is correct. • The programme is applicable for the type of load and for the degree of soil. • The correct quantity of detergent is used. UNLOADING THE BASKETS 1.
INTERNAL CLEANING • Carefully clean the appliance, including the rubber gasket of the door, with a soft damp cloth. • If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance. To prevent this, we recommend to run long duration programmes at least 2 times per month. • To maintain the performance of your appliance at its best, we recommend to use monthly a specific cleaning product for dishwashers.
Problem and alarm code Possible cause and solution The program lasts too long. • If the delayed start option is set, cancel the delay setting or wait for the end of the countdown. The remaining time in the display increases and skips nearly to the end of program time. • This is not a defect. The appliance is working correctly. Small leak from the appliance door. • The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable). The appliance door is not centred on the tub.
Problem Possible cause and solution There are whitish streaks or bluish layers on glasses and dishes. • There are stains and dry water drops on glasses and dishes. • The dishes are wet. • • • • • • • The release quantity of rinse aid is too much. Adjust the rinse aid level to a lower level. The quantity of detergent is too much. The released quantity of rinse aid is not sufficient. Adjust the rinse aid level to a higher level. The quality of the rinse aid can be the cause.
TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 596 / 818 - 898 / 555 Electrical connection 1) Voltage (V) 200 - 240 Frequency (Hz) 50 / 60 Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 13 Power consumption Left-on mode (W) 5.0 Power consumption Off-mode (W) 0.10 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy, (e.g.
156902160-A-502015 WWW.ZANUSSI.