User Manual GETTING STARTED? EASY.
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference.
• • • • • Do not keep the appliance door open without supervision to prevent to fall on it. Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. Do not use water spray and steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet. The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused.
• • The appliance can release hot steam if you open the door while a programme operates. Do not put flammable products or items that are wet with flammable products in, near or on the appliance. SERVICE • Contact the Authorised Service Centre to repair the appliance. We recommend only the use of original spare parts. • When you contact the Authorised Service Centre, ensure that you have the following information that is available on the rating plate.
EASY START 1 2 1 On/off button 2 Programme buttons 3 4 4 Indicators 3 Delay button INDICATORS Indicator Description End indicator. Multitab indicator. Salt indicator. It is always off while the programme operates. PROGRAMMES Consumption values 1) Programme Degree of soil Type of load Programme phases Duration (min) 2) 3) Energy (kWh) Water (l) Normal soil Crockery and cutlery • • • • Prewash Wash 50 °C Rinses Dry 195 1.
Consumption values 1) Programme Degree of soil Type of load Programme phases Duration (min) 4) 5) Energy (kWh) Water (l) Heavy soil Crockery, cutlery, pots and pans • • • • Prewash Wash 70 °C Rinses Dry 150 170 1.5 - 1.6 13 - 15 Fresh soil Crockery and cutlery • 30 0.8 9 • Wash 60 °C or 65 °C Rinses Normal or light soil Delicate crockery and glassware • • • Wash 45 °C Rinses Dry 70 - 80 0.7 - 0.
CANCEL FUNCTION Press and hold simultaneously and until the appliance is in programme selection mode. With this function you can cancel the running programme or the delay start. USER MODE While the appliance is in programme selection mode: 1. Press and hold and . • The indicators , and starts to flash. In user mode can be changed: • The level of the water softener according to the water hardness. • The activation or the deactivation of the acoustic signal for end of programme.
2. Press to change the setting. Each time you press you will start again from level by 1. 3. Press the on/off button to confirm the setting. , the level increases. After level 10 THE WATER HARDNESS TABLE German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 47 -50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.
DEACTIVATING THE RINSE AID DISPENSER While the appliance is in user mode: 1. Press . • The indicators and goes off. • • The indicator starts to flash. The end indicator indicates the current setting: End indicator on = rinse aid dispenser activated. 2. Press to change the setting. End indicator off = rinse aid dispenser deactivated. 3. Press the on/off button to confirm the setting. BEFORE FIRST USE 1.
ADDING RINSE AID 1 43 21 A 2 The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot rinse phase. Fill the rinse aid dispenser when the indicator (A) becomes clear. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. 3. Load the baskets. 4. Add the detergent.
The function comes into operation: • 5 minutes after the completion of the programme. • After 5 minutes if the programme has not started. Starting a programme 1. Keep the appliance door ajar. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. 3. Press the button related to the programme you want to start. The related programme indicator comes on. 4. Close the appliance door to start the programme. Option delay 1. Set the programme. 2.
With the use of this option the programme duration is prolonged to increase the cleaning and drying results with the use of multi-tablets. Opening the door while the appliance operates If you open the door while a programme is running, the appliance stops. When you close the door, the appliance continues from the point of interruption. If the door is opened for more than 30 seconds during the drying phase, the running programme will end. Press on/off button or wait for AUTO OFF to deactivate the appliance.
• the tableware, we recommend that you use the tablets with long programmes. Do not use more than the correct quantity of detergent. Refer to the instructions on the detergent packaging. WHAT TO DO IF YOU WANT TO STOP USING MULTI-TABLETS Before you start to use separately detergent, salt and rinse aid do the following procedure. 1. Set the highest level of the water softener. 2. Make sure that the salt and rinse aid containers are full. 3. Start the shortest programme with a rinsing phase.
C • • • • Make sure that there are no residues of food or soil in or around the edge of the sump. Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides. Reassemble the filters (A) and (B). Put back the filter (A) in the flat filter (C). Turn it clockwise until it locks. An incorrect position of the filters can cause bad washing results and damage to the appliance CLEANING THE SPRAY ARMS Do not remove the spray arms.
Problem and alarm code You cannot activate the appliance. Possible cause and solution • • The programme does not start. • • • Make sure that the mains plug is connected to the mains socket. Make sure that there is no damaged fuse in the fuse box. Make sure that the appliance door is closed. If the delay start is set, cancel the setting or wait for the end of the countdown. The appliance has started the procedure to recharge the resin inside the water softener.
Problem and alarm code Possible cause and solution The appliance trips the circuit-beaker. • • The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use. Internal electrical fault of the appliance. Contact an Authorised Service Centre. For alarm codes not described in the table, contact an Authorised Service Centre.
Problem Possible cause and solution Unusual foam during washing. • • Use the detergent for dishwashers only. There is a leak in the rinse aid dispenser. Contact an Authorised Service Centre. Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to "The water softener". Silver and stainless steel cutlery were placed together. Avoid to put silver and stainless steel items close together. • There are residues of detergent in the dispenser at the end of the programme.
RATING PLATE INFORMATION FOR TEST INSTITUTES For all the necessary information for test performance, send an email to: info.test@dishwasher-production.com Write down the product number (PNC) that is on the rating plate. Mod. ... ... ... Prod. No. ... ... ... Ser. No. ... ENVIRONMENT CONCERNS the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office. Recycle the materials with the symbol .
100003151-A-182015 WWW.ZANUSSI.