EN User manual Dishwasher ZDT15002
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Options _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Before first use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 3 4 4 5 5 Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10
– By clients in hotels, motels and other residential type environments – Bed and breakfast type environments. Warning! Risk of injury. • Do not change the specification of this appliance. • Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. • Do not keep the appliance door open without supervision to prevent to fall on it. • Do not sit or stand on the open door. • Dishwasher detergents are dangerous.
Control panel 2 1 A B 4 3 C 5 1 On/off button 2 Programme buttons 4 Indicators 5 Function buttons 3 Delay button Indicators Description Salt indicator. This indicator is off while the programme operates. Rinse aid indicator. This indicator is off while the programme operates. End indicator.
Degree of soil Type of load Programme1) 4) All Programme phases Prewash Duration (min) 12 Energy (kWh) 0,1 Water (l) 4 1) The water pressure and temperature, the variations of the mains supply, the options and the quantity of dishes can change the programme duration and the consumption values. 2) With this programme you can wash a load with fresh soil. It gives good washing results in a short time. 3) This is the standard programme for test institutes.
Adjusting the water softener Hard water contains a high quantity of minerals that can cause damage to the appliance and bad washing results. The water softener neutralises these minerals. The dishwasher salt keeps the water softener clean and in good conditions. Refer to the table to adjust the water softener to the right level. It makes sure that the water softener uses the correct quantity of dishwasher salt and water. You must adjust the water softener manually and electronically.
5. Press function button (AA) again and again to change the setting. Each time you press function button (AA) you go to the next level. 6. Deactivate the appliance to confirm. Filling the rinse aid dispenser Caution! Only use rinse aid for dishwashers. Other products can cause damage to the appliance. The rinse aid, during the last rinsing phase, helps to dry the dishes without streaks and stains. Filling the salt container Caution! Only use dishwasher salt.
2. Press the on/off button to activate the appliance. Make sure that the appliance is in setting mode. Refer to ’SETTING AND STARTING A PROGRAMME’. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5. Set and start the correct programme for the type of load and soil. Loading the baskets Refer to the supplied leaflet with examples of the load of the baskets.
1. Adjust the water softener to the lowest level. 2. Set the rinse aid dispenser to the lowest position. If you stop to use the combi detergent tablets, before you start to use separately detergent, rinse aid and dishwasher salt, do these steps: 1. Press the on/off button to activate the appliance. 2. Set the water softener to the highest level. 3. Make sure that the salt container and the rinse aid dispenser are full. 4.
Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. D Cleaning the filters A C 5 Put filter (AA) to its initial position. Make sure that it assembles correctly under D). the two guides (D B A 2 1 6 Assemble filters (BB) and C). Put them into position (C in filter (AA). Turn the handle clockwise until it locks. An incorrect position of the filters can cause bad washing results and damage to the appliance.
Alarm code Problem • The indicator of the set programme flashes continuously. • The end indicator flashes 3 times intermittently. The anti-flood device is on. Warning! Deactivate the appliance before you make the checks. Problem The programme does not start. The appliance does not fill with water. Possible cause Possible solution The mains plug is not connected in the mains socket. Connect the mains plug. The appliance door is open. Close the appliance door. The fuse in the fuse box is damaged.
Problem Limescale particles on the dishes. Whitish streaks and stains or bluish layers on glasses and dishes. Dry water drop stains on glasses and dishes. Possible cause Possible solution The spray arms are clogged. Remove remaining soil with a thin pointed object. The programme was not applicable for the type of load and soil. Make sure that the programme is applicable for the type of load and soil. Incorrect position of the items in the baskets. Water could not wash all items.
Technical information Dimensions Width / Height / Depth (mm) Electrical connection Refer to the rating plate. Voltage 596 / 818-898 / 555 220-240 V Frequency 50 Hz Water supply pressure Min. / max. (bar / MPa) (0.5 / 0.05 ) / (8 / 0.8 ) Water supply 1) Cold water or hot water2) Capacity Place settings max. 60 °C 12 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 2) If the hot water comes from alternative sources of energy, (e.g.
156957961-A-052012 www.zanussi.
