EN User manual Dishwasher ZDI12010XA
Contents Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Before first use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 4 5 7 Hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Technical information _ _ _ _ _ _ _ _ _ _ _ 12 Environment concerns _ _ _ _ _ _ _ _ _ _ _ 12 Subject to change wi
• The water inlet hose has a safety valve and a sheath with an inner mains cable. Warning! Dangerous voltage. If the water inlet hose is damaged, imme• diately disconnect the mains plug from the mains socket. Contact the service to replace the water inlet hose.
Control panel 1 2 3 6 5 4 1 On/off indicator 2 Programme marker 4 Delay button 5 Start button 3 Indicators 6 Programme knob Indicators Description Washing phase indicator. Drying phase indicator. End indicator. Salt indicator. This indicator is off while the programme operates. Programmes Programme 1) 2) 4 Degree of soil Type of load Programme phases Duration (min) Energy (kWh) Water (l) Heavy soil Crockery, cutlery, pots and pans Prewash Wash 70 °C Rinses Dry 130 - 150 1.3 - 1.
Programme 1) 3) 4) Degree of soil Type of load Programme phases Duration (min) Energy (kWh) Water (l) Normal soil Crockery and cutlery Prewash Wash 50 °C Rinses Dry 195 1.02 11 All Prewash 14 0.1 4 1) The pressure and the temperature of the water , the variations of the mains supply, the options and the quantity of dishes can change the values. 2) With this programme you can wash a load with fresh soil. It gives good washing results in a short time.
Water softener adjustment Water hardness German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Level 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 < 0.7 <5 12) 1) Factory position. 2) Do not use salt at this level. How to adjust the level of the water softener 1. Make sure that the programme marker on the knob is aligned with the on/off indicator. 2. Press and hold the delay button.
Fill the rinse aid dispenser when the lens (A) is clear. 3 To adjust the released quantity of rinse aid, turn the selector between position 1 (lowest quantity) and position 4 (highest quantity). 1 4 1 2 A 2 3 4 Daily use 1. Open the water tap. 2. Turn the programme knob until the programme marker is aligned with the programme you want to set. Make sure that the appliance is in setting mode, refer to “Setting and starting a programme”.
3. Start the shortest programme with a rinsing phase, without detergent and without dishes. 4. Adjust the water softener to the water hardness in your area. 5. Adjust the released quantity of rinse aid. Cancelling the delay start while the countdown operates Setting and starting a programme Make sure that there is detergent in the detergent dispenser before you start a new programme. Setting mode The appliance must be in setting mode to start a programme.
Hints and tips The water softener Hard water contains a high quantity of minerals that can cause damage to the appliance and bad washing results. The water softener neutralises these minerals. The dishwasher salt keeps the water softener clean and in good conditions. It is important to set the right level of the water softener. This makes sure that the water softener uses the correct quantity of dishwasher salt and water.
Cleaning the filters To remove filters (B) and (C), turn the handle counterclockwise and remove. Pull apart filter (B) and (C). Wash the filters with water. Remove filter (A). Wash the filter with water. Before you put the filter (A) back, make sure that there are no residues of food or soil in or around the edge of the sump. Make sure that filter (A) is correctly positioned under the 2 guides (D). Assemble filters (B) and (C). Put them back in filter (A). Turn the handle clockwise until it locks.
Alarm code Problem • The start indicator flashes continuously. • The end indicator flashes 1 time intermittently. The appliance does not fill with water. • The start indicator flashes continuously. • The end indicator flashes 2 times intermittently. The appliance does not drain the water. • The start indicator flashes continuously. • The end indicator flashes 3 times intermittently. The anti-flood device is on. Warning! Deactivate the appliance before you do the checks.
• The quality of the detergent can be the cause. Dishes are wet • The programme is without a drying phase or with a low temperature drying phase. • The rinse aid dispenser is empty. • The quality of the rinse aid can be the cause. Refer to ‘HINTS AND TIPS’ for other possible causes. Technical information Dimensions Width / Height / Depth (mm) Electrical connection Refer to the rating plate. Voltage 596 / 818 - 898 / 575 220-240 V Frequency 50 Hz Water supply pressure Min. / max. (bar / MPa) (0.
www.zanussi.
www.zanussi.
www.zanussi.
156970840-A-362013 www.zanussi.