GAS HOB ZDG 322 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation z z z z This appliance must be installed and serviced by a competent person as stated in the Gas Safety (Installation and Use) Regulations Current Editions and the IEE Wiring Regulations. Remove all packaging before using the hob.
Contents For the Installer For the User Important Safety Information 3 Instructions for the Installer 10 Description of the Hob 4 Important safety requirements 11 Operation 5 Installation 12 Maintenance and Cleaning 6 Building In 13 Something Not Working? 7 Electrical connections 15 Customer Care Department 8 Wiring Diagram 16 Guarantee Conditions 9 Fault Finding 16 Commissioning 18 Conversion from Natural Gas to LPG 18 This appliance complies with the following E.E.C.
Operation Hob burners The hob burner control knobs are situated on the hob front panel. The symbols on the knobs mean that : there is no gas supply z there is maximum gas supply / Ignition setting there is minimum gas supply ) To light a burner: turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner; z then, check the flame is regular and adjust it as required.
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. Never use steam or high pressure steam cleaners to clean the appliance. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added.
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM There is no spark when lighting the gas SOLUTION Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e.g. after cleaning.
Customer Care Department For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.zanussi.co.uk Customer Care Department Major Appliances Addington Way Luton Bedfordshire LU4 9QQ 08705 727727 (*) * calls to this number may be recorded for training purposes.
Guarantee Conditions Zanussi Guarantee conditions We, Zanussi, undertake that if, within 24 months of the date of the purchase, this Zanussi appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: * The appliance has been correctly installed and used only on the gas and electricity supply stated on the rating plate.
Instructions for the Installer Engineers technical data OVERALL DIMENSIONS Width: Depth: 290 mm 510 mm Rapid Burner Heat Input 3.0 kW (10236 BTU/HR) Auxiliary Burner Heat Input 1.0 kW (3413 BTU/HR) CUT OUT DIMENSIONS Width: Depth: 270 mm 490 mm SUPPLY CONNECTIONS Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Burner VALUE = 37.78 MJ/m3 CHARACTERISTICS Ws - 50.7 MJ/ m3 VALUE = 49.
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Provision for ventilation Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Part 2 and B.S. 6891 Current Editions. The hob should not be installed in a bed sitting room with a volume of less than 20 m3.
Installation IMPORTANT: This hob must be installed by a competent person to the relevant Gas Standards. Any gas installation must be carried out by a competent person. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory.
Building In Fig. 1 51 0 29 0 These hobs can be inserted in a built-in kitchen unit whose depth is between 550 and 600 mm. The hobs dimensions are shown in Fig. 1. Installation and assembly These hobs can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in Fig. 2. The edge of the cut out must have a minimum distance from the rear wall of 55 mm.
Building over a kitchen unit with door Proper arrangements must be taken in designing the forniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in Fig. 4. The panel fitted under the hob should be easily removable to allow an easy access if a technical assistance intervention is needed. Building over a kitchen unit with oven The hob recess dimensions must comply the indication given in Fig.
Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. The manufacturer declines any liability should these safety measures not be observed. Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm.
Wiring Diagram A. IGNITOR SWITCH B. IGNITOR UNIT Fault Finding Brown PLUG (with cover removed) Earth Wire Green/Yellow Blue START Isolate appliance and carry out: A: Earth Continuity check. Neutral Wire Blue SOCKET (face view) ( ) E( ) FUSE Preliminary Electrical Systems Check N L Blue Brown Green Yellow YES NO Carry out: C: Polarity check. Has inlet fuse blown? NO YES Inlet wiring faulty. Rectify any fault. Isolate appliance and carry out: B: Insulation check.
Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Light burner manually Check polarity and earth continuity of supply point Check by pass simmer adjusted Check position of the electrode Check earth continuity of appliance Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from 'L' on the mains connector block and the taps ignition switches Check continuity from igni
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: Re-ignite the burner and set to MIN. Remove the control knob.
CUSTOMER CARE Major Appliances Addington Way Luton Bedfordshire LU4 9QQ © Electrolux plc 2003 From the Electrolux Group. The world’s No.1 choice. 35690-8301 07/05 Grafiche MDM - Forlì The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx.
