User Manual GETTING STARTED? EASY.
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
• • • • • • Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance.
• • • Do not remove the dishes from the appliance until the programme is complete. Some detergent may remain on the dishes. The appliance can release hot steam if you open the door while a programme operates. Do not put flammable products or items that are wet with flammable products in, near or on the appliance. SERVICE • Contact the Authorised Service Centre to repair the appliance. We recommend only the use of original spare parts.
CONTROL PANEL 1 2 5 1 On/off button 2 Display 3 4 4 Delay button 5 Programme buttons 3 Indicators INDICATORS Indicator Description XtraDry indicator. Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates.
PROGRAMMES Consumption values 1) Programme Degree of soil Type of load Programme phases Duration (min) 2) 3) 4) Energy (kWh) Water (l) Normal soil Crockery and cutlery • • • • Pre-wash Wash 50 °C Rinses Dry 227 1.039 11 All Crockery, cutlery, pots and pans • • 45 - 156 0.7 - 1.4 7 - 12 • • Pre-wash Wash from 45 °C to 70 °C Rinses Dry Heavy soil Crockery, cutlery, pots and pans • • • • Pre-wash Wash 70 °C Rinses Dry 155 170 1.5 - 1.
CANCEL FUNCTION Use CANCEL to: • CANCEL the currently running programme. • Stop the countdown of the Delay option. • Bring the appliance back to the programme selection mode. ADJUSTING THE WATER SOFTENER Make sure that the appliance is in user mode: 1. Press To CANCEL, press and hold and until the appliance is in programme selection mode. USER MODE User mode allows to change the following settings: • Adjust the level of the water softener according to the water hardness.
• • The indicator flashes. The display shows the current setting: – = rinse aid empty notification activated. – = rinse aid empty notification deactivated. 2. Press to change the setting. 3. Press on/off to confirm the setting. When rinse aid chamber is empty, the rinse aid indicator is on prompting to refill the rinse aid. If you are using multi-tabs containing rinse aid and you are satisfied with the drying result, you can deactivate the notification.
ADDING SALT Before the first use, put one litre of water in the salt container. CAUTION! Water and salt can come out of the salt container during filling. To prevent corrosion, start a programme immediately after filling the salt container. ADDING RINSE AID 4 1 2 2 3 1 1 2 1 43 21 2 The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot rinse phase. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance.
ADDING DETERGENT 1 A B 30 20 2 1 A B 30 20 2 If the programme has a prewash phase, put a small quantity of detergent also in compartment B. ADDING MULTI-TABLETS 1 30 20 2 1 30 20 2 • Adjust the water softener to the lowest level. THE AUTO OFF FUNCTION This function decreases energy consumption by deactivating automatically the appliance when it is not operating. The function comes into operation: • 5 minutes after the completion of the programme.
4. Set the applicable options. 5. Close the appliance door to start the programme. XTRADRY OPTION Activate this option when you want to boost the drying performance. With the use of this option, the duration of some programmes, water consumption and the last rinse temperature can be affected. The XtraDry option is a permanent option for all programmes other than be selected at every cycle. and need not to DELAY OPTION 1. Set a programme. 2.
• • • (powder, gel, tablets containing no additional agents), rinse aid and salt separately for optimal cleaning and drying results. At least once a month run the appliance with the use of appliance cleaner which is particularly suitable for this purpose. Detergent tablets do not fully dissolve with short programmes. To prevent detergent residues on the tableware, we recommend that you use the tablets with long programmes. Do not use more than the correct quantity of detergent.
CLEANING THE FILTERS B A C • • • • Make sure that there are no residues of food or soil in or around the edge of the sump. Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides. Reassemble the filters (A) and (B). Put back the filter (A) in the flat filter (C). Turn it clockwise until it locks. An incorrect position of the filters can cause bad washing results and damage to the appliance CLEANING THE SPRAY ARMS Do not remove the spray arms.
The majority of problems that can occur can be solved without the need to contact an Authorised Service Centre. Problem and alarm code Possible cause and solution You cannot activate the appliance. • The program does not start. • • • • The appliance does not fill with water. • • • • • • • Make sure that the sink spigot is not clogged. Make sure that the filter in the outlet hose is not clogged. Make sure that the interior filter system is not clogged.
Problem and alarm code The appliance trips the circuitbeaker. Possible cause and solution • The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use. Internal electrical fault of the appliance. Contact an Authorised Service Centre. • For alarm codes not described in the table, contact an Authorised Service Centre.
Problem Possible cause and solution The interior of the appliance is wet. • This is not a defect of the appliance. it is caused by the humidity in the air that condenses on the walls. Unusual foam during washing. • • Use the detergent for dishwashers only. There is a leak in the rinse aid dispenser. Contact an Authorised Service Centre. Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to "The water softener".
Capacity Place settings 13 Power consumption Left-on mode (W) 5.0 Power consumption Off-mode (W) 0.50 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot water supply to decrease energy consumption. RATING PLATE INFORMATION FOR TEST INSTITUTES For all the necessary information for test performance, send an email to: info.test@dishwasher-production.
156917640-A-172017 WWW.ZANUSSI.
