User Manual GETTING STARTED? EASY.
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
• • • • • • Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance.
• Do not put flammable products or items that are wet with flammable products in, near or on the appliance. SERVICE • Contact the Authorised Service Centre to repair the appliance. We recommend only the use of original spare parts. • When you contact the Authorised Service Centre, ensure that you have the following information that is available on the rating plate. Model : PNC : Serial Number : DISPOSAL WARNING! Risk of injury or suffocation. • • • 4 Disconnect the appliance from the mains supply.
EASY START 1 2 6 1 On/off indicator 2 Programme marker 3 5 4 5 Delay button 6 Programme knob 3 Indicators 4 Start button INDICATORS End indicator. Salt indicator. It is always off while the programme operates. Rinse aid indicator. It is always off while the programme operates.
PROGRAMMES Consumption values 1) Programme Degree of soil Type of load Programme phases Duration (min) 2) 3) 4) Energy (kWh) Water (l) Normal soil Crockery and cutlery • • • • Prewash Wash 50 °C Rinses Dry 222 1.039 11 Heavy soil Crockery, cutlery, pots and pans • • • • Prewash Wash 70 °C Rinses Dry 155 170 1.5 - 1.7 14-15 Normal soil Crockery and cutlery • • • • Prewash Wash 65 °C Rinses Dry 130 140 1.4 - 1.6 15-17 Fresh soil Crockery and cutlery • 30 0.
SETTINGS ADJUSTING THE WATER SOFTENER 6x 5x The programme marker must be in 1. Press and hold position. and simultaneously turn the knob counterclockwise until the programme marker is in position. 2. Release • when and Delay start to flash. The current setting is indicated by the number of flashes of the indicator pause + 5 flashes... = level 5. (e.g. 5 flashes + 3. Press to change the setting. Each pressing of the programme button increases the level number.
German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Factory setting 2) Do not use salt at this level. ACTIVATING AIRDRY AirDry improves the drying results with less energy consumption. By default, AirDry is activated with all programmes excluding deactivate it. (if applicable) but it is possible to While the drying phase operates, the device opens the appliance door. The door is then kept ajar.
The programme marker must be in 1. Press and hold position. and simultaneously turn the knob counterclockwise until the programme marker is in position. 2. Release when and Delay start to flash. 3. Turn the knob counterclockwise until the programme marker is in • The indicator 4. Press • position. is on = AirDry is activated. to change the setting. The indicator 5. Turn the knob to is off = AirDry is deactivated. to confirm the setting.
CAUTION! Water and salt can come out of the salt container during filling. To prevent corrosion, start a programme immediately after filling the salt container. ADDING RINSE AID 1 43 21 2 The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot rinse phase. DAILY USE 1. Open the water tap. 2. Set the correct programme for the type of load and the degree of soil. Make sure that the appliance is in Programme selection mode.
ADDING MULTI-TABLETS 1 30 20 2 • • Do not fill the salt container and the rinse aid dispenser. Set the rinse aid dispenser to the lowest position. PROGRAMME SELECTION MODE The appliance must be in Programme selection mode to start a programme. If the control panel does not show this condition, do the Reset. Press and hold simultaneously Delay and until the appliance is in programme selection mode. RESET With Reset you can cancel the running programme or the delay start.
1. Open the water tap and close the door. 2. Select a programme. 3. Press . OPTION DELAY With this option you can postpone the start of a programme by 3 hours. 1. Set the programme. 2. Press Delay. to start the countdown. 3. Press When the countdown is completed, the programme starts. OPENING THE DOOR WHILE THE APPLIANCE OPERATES Opening the door while a programme is running stops the appliance. It may affect the energy consumption and the programme duration.
AT THE END OF THE PROGRAMME 5 min The indicator is on. After 5 minutes of non-use, the appliance enters standby mode and all the indicators are off. It decreases energy consumption. 1. Turn the knob to 2. Close the tap. . HINTS AND TIPS GENERAL The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • Remove larger residues of food from the dishes into the waste bin. • Do not pre-rinse dishes by hand.
• • Detergent tablets do not fully dissolve with short programmes. To prevent detergent residues on the tableware, we recommend that you use the tablets with long programmes. Do not use more than the correct quantity of detergent. Refer to the instructions on the detergent packaging. WHAT TO DO IF YOU WANT TO STOP USING MULTI-TABLETS Before you start to use separately detergent, salt and rinse aid do the following procedure. 1. Set the highest level of the water softener. 2.
Problem and alarm code You cannot activate the appliance. Possible cause and solution • • The programme does not start. • Make sure that the appliance door is closed. • • Press . If the delay start is set, cancel the setting or wait for the end of the countdown. The appliance has started the procedure to recharge the resin inside the water softener. The duration of the procedure is approximately 5 minutes. • The appliance does not fill with water. • The end indicator flashes 1 time intermittently.
Problem and alarm code Possible cause and solution The appliance trips the circuit-beaker. • • The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use. Internal electrical fault of the appliance. Contact an Authorised Service Centre. For alarm codes not described in the table, contact an Authorised Service Centre.
Problem Possible cause and solution The interior of the appliance is wet. • This is not a defect of the appliance. it is caused by the humidity in the air that condenses on the walls. Unusual foam during washing. • • Use the detergent for dishwashers only. There is a leak in the rinse aid dispenser. Contact an Authorised Service Centre. Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to "The water softener".
CLEANING THE FILTERS B A C • • • • Make sure that there are no residues of food or soil in or around the edge of the sump. Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides. Reassemble the filters (A) and (B). Put back the filter (A) in the flat filter (C). Turn it clockwise until it locks. An incorrect position of the filters can cause bad washing results and damage to the appliance CLEANING THE SPRAY ARMS Do not remove the spray arms.
Capacity Place settings 13 Power consumption Left-on mode (W) 5.0 Power consumption Off-mode (W) 0.50 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot water supply to decrease energy consumption. RATING PLATE INFORMATION FOR TEST INSTITUTES For all the necessary information for test performance, send an email to: info.test@dishwasher-production.
156912790-A-492016 WWW.ZANUSSI.