EN User manual Dishwasher ZDF2020 2
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Washing programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Use of the appliance _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Setting the water softener _ _ _ _ _ _ _ _ _ _ _ _ _ Use of dishwasher salt _ _ _ _ _ _ _ _ _ _ _ _ _ _ Use of rinse aid _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Loading cutlery and dishes _ _ _ _ _ _ _ _ _ _ _ _ Use of detergent _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 3 4 5 5 6 7 7 9 Setting and starting
• Do not change the specifications or modify this product. Risk of injury and damage to the appliance. • Do not use the appliance: – if the mains cable or water hoses are damaged, – if the control panel, worktop or plinth area are damaged, that you can get access to the inner side of the appliance. Contact your local Service Force Centre. • Do not drill into the sides of the appliance to prevent damage to hydraulic and electrical components.
Indicator lights Rinse aid Comes on when it is necessary to fill the rinse aid container. Refer to 'Use of rinse aid'. 1) 1) When the salt and/or rinse aid containers are empty, the related indicator lights do not come on while a washing programme operates. Delay start button Use the delay start button to delay the start of the washing programme with an interval of 3 hours. Refer to the chapter 'Setting and starting a washing programme'.
Consumption values Programme Programme duration (in minutes) Energy consumption (in kWh) Water consumption (in litres) 85-95 1,8-2,0 22-25 105-115 1,5-1,7 23-25 30 0,9 9 130-140 1,0-1,2 14-16 12 0,1 5 The pressure and temperature of the water, the variations of power supply and the quantity of dishes can change these values. Use of the appliance Refer to the following instructions for each step of procedure: 1.
Water hardness Water hardness setting °dH °TH mmol/l Clarke manually electronically 15 - 18 26 - 32 2,6 - 3,2 18 - 22 1 4 11 - 14 19 - 25 1,9 - 2,5 13 - 17 1 3 4 - 10 7 - 18 0,7 - 1,8 5 - 12 1 2 <4 <7 < 0,7 <5 11) 11) 1) No use of salt required. You must set the water softener manually and electronically. Manual adjustment The appliance is set at the factory at position 2. 1 2 Set switch to position 1 or 2. 1. Press and hold the start/cancel button.
It is normal that water overflows from the salt container when you fill it with salt. Make sure that there is no grain of salt outer of the salt compartment. Salt which stays on the tank for a while drills the tank. It is recommended to start a washing programme immediately after you fill the salt container. This prevents of corrosion because of spilled salt. 6 5 When you set electronically the water softener to level 1, the salt indicator light does not stay on.
• While you load cutlery and dishes, do these steps: – Load hollow items (e.g. cups, glasses and pans) with the opening down. – Make sure that water does not collect in the container or in a deep base. – Make sure that cutlery and dishes do not lie inside one another. – Make sure that cutlery and dishes do not cover other cutlery and dishes. – Make sure that glasses do not touch other glasses. – Put small objects in the cutlery basket.
Maximum height of the dishes in : upper basket lower basket Upper position 20 cm 31 cm Lower position 24 cm 27 cm Do these steps to move the upper basket to the upper or lower position: 1. Move the front runner stops (A) out. 2. Pull the basket out. 3. Put the basket in the upper or lower position. 4. Replace the front runner stops (A) in their initial position. Caution! If the basket is in the upper position, do not put cups on the cup racks.
• rinse aid • other cleaning agents. Do these steps to use detergent tablets: 1. Make sure that the detergent tablets are applicable for your water hardness. Refer to the instructions from the manufacturer. 2. Set the lowest levels of water hardness and rinse aid dosage. It is not necessary to fill the salt container and the rinse aid dispenser. Do these steps when the drying results are not satisfactory: 1. Fill the rinse aid dispenser with rinse aid. 2. Set the rinse aid dosage to position 2.
• The end indicator light comes on. For better drying results, keep the door ajar for some minutes before you remove the dishes. Let the dishes cool down before you remove them from the appliance. Hot dishes are easily damaged. • There can be water on the sides and door of the appliance. Stainless steel becomes cool more quickly than the dishes. Removing the load • First remove items from the lower basket, then from the upper basket.
What to do if… The appliance does not start or stops during operation. If there is a fault, first try to find a solution to the problem yourself. If you cannot find a solution to the problem yourself, contact the Service Force Centre. Fault code and malfunction Caution! Switch off the appliance before you do the below suggested corrective actions. Possible cause and solution • continuous flash of the start/cancel in- • The water tap is blocked or furred with limescale. dicator light Clean the water tap.
The cleaning results are not satisfactory The dishes are not clean • The selected washing programme is not applicable for the type of load and soil. • The baskets are loaded incorrectly so that water cannot reach all surfaces. • Spray arms do not turn freely because of incorrect arrangement of the load. • The filters are dirty or not correctly installed. • The quantity of detergent is too little or missing. Limescales particles on the dishes • The salt container is empty.
Warning! To discard the appliance, follow the procedure: • Pull the mains plug out of the socket. • Cut off the mains cable and mains plug and discard them. • Discard the door catch. This prevents the children to close themselves inside the appliance and endanger their lives. Installation Warning! Make sure that mains plug is disconnected from the mains socket during installation. Fitting under a counter Put the appliance adjacent to a water tap and a water drain.
The internal diameter must not be smaller than the diameter of the hose. If you connect the water drain hose to a trap spigot under the sink, remove the plastic membrane (A). If you do not remove the membrane, remaining food can cause a blockage in the drain hose spigot. Caution! Make sure that the water couplings are tight to prevent water leakage. 3 4 Electrical connection Warning! The manufacturer is not responsible if you do not follow these safety precautions.
www.zanussi.com 156985810-00-052009 To buy accessories, consumables and spare parts at our online shop please visit: www.zanussi.co.