User Manual GETTING STARTED? EASY.
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
• • • • • • • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it.
Authorised Service Centre to replace the water inlet hose. SERVICE • To repair the appliance contact an Authorised Service Centre. • Use original spare parts only. USE • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is complete. Some detergent may remain on the dishes.
INDICATORS Indicator Description Salt indicator. It is on when the salt container needs refilling. It is always off while the programme operates. Rinse aid indicator. It is on when the rinse aid dispenser needs refilling. It is always off while the programme operates. Running programme indicator. It comes on when the programme starts and goes out when the programme is completed. TimeManager indicator. XtraDry indicator. Hygiene indicator.
Consumption values 1) Programme Degree of soil Type of load Programme phases Water (l) • 6) • 7) • • Energy (kWh) Duration (min) Normal or light soil Delicate crockery and glassware • • • Wash 45 °C Rinses Dry 12 - 14 0.7 - 0.9 82 - 92 Fresh soil Crockery and cutlery • • Wash 60 °C Rinses 10 0.9 30 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values.
1. Press and hold Delay and XtraDry until the • indicators , , and flash and the display is blank. As the appliance stores the saved settings, there is no need to configure it before every cycle. = level 5. 2. Press Program to change the setting. 3. Press on/off button to confirm the setting. If you use detergent or multi-tablets containing salt and the hardness of your water is lower than 21°dH, you can set the lowest water softener level. It deactivates the salt refill indicator.
• • The indicator still flashes. The display shows the current setting: e.g. = level 4. – The levels of rinse aid range from 0A to 6A. – Level 0A means no rinse aid is used. 2. Press Delay repeatedly to change the setting. 3. Press on/off to confirm the setting. DEACTIVATING AIRDRY AirDry improves the drying results with less energy consumption. The appliance door opens automatically during the drying phase and remains ajar. AirDry is automatically activated with all programmes excluding (if applicable).
XTRADRY Activate this option to boost the drying performance. XtraDry is a permanent option for all programmes other than . It is automatically activated in next cycles. This configuration can be changed at any time. Every time is activated, XtraDry is off and needs to be chosen manually. TIMEMANAGER The TimeManager allows to reduce the duration of a selected programme by approximately 50%. The washing results are the same as with the normal programme duration. The drying results can decrease.
ADDING RINSE AID A The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot rinse phase. • Fill the dispenser until the rinse aid reaches the marking "MAX". • Remove any spilled rinse aid with an absorbent cloth to prevent excessive foaming during the washing cycle. • Fill the rinse aid dispenser when the indicator (A) becomes clear. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance.
• • Adjust the water softener to the lowest level. Set the rinse aid dispenser to the lowest position. STARTING A PROGRAMME 1. Keep the appliance door ajar. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. 3. Press Program again and again until the indicator of the programme you want to select comes on. • If you want to select the MyFavourite programme, press and hold Program until the MyFavourite setting comes on.
• tablets (e.g. ''3in1'', ''4in1'', ''All in 1''). Follow the instructions written on the packaging. Select the programme according to the type of load and degree of soil. With the ECO programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. USING SALT, RINSE AID AND DETERGENT • Only use salt, rinse aid and detergent for dishwasher. Other products can cause damage to the appliance.
CLEANING THE FILTERS B A C • • • • Make sure that there are no residues of food or soil in or around the edge of the sump. Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides. Reassemble the filters (A) and (B). Put back the filter (A) in the flat filter (C). Turn it clockwise until it locks.
INTERNAL CLEANING • Carefully clean the appliance, including the rubber gasket of the door, with a soft damp cloth. • To maintain the performance of your appliance, use a cleaning product designed specifically for dishwashers at least once a month. Carefully follow the instructions on the packaging of the product. • • Do not use abrasive products, abrasive cleaning pads, sharp tools, strong chemicals, scourer or solvents.
Problem and alarm code The programme lasts too long. Possible cause and solution • • If the delay start option is set, cancel the delay setting or wait for the end of the countdown. Activate the TimeManager option to reduce the programme duration. Activating options can increase the programme duration. The remaining time in the display increases and skips nearly to the end of the programme duration. • This is not a defect. The appliance is working correctly. Small leak from the appliance door.
Problem Poor drying results. Possible cause and solution • • • • • There are whitish streaks or bluish layers on glasses and dishes. • There are stains and dry water drops on glasses and dishes. • The dishes are wet. • • • • • • • The released quantity of rinse aid is too high. Adjust the rinse aid level to a lower level. The quantity of detergent is too high. The released quantity of rinse aid is not sufficient. Adjust the rinse aid level to a higher level.
Problem Possible cause and solution Limescale deposits on the tableware, on the tub and on the inside of the door. • • • • • • • Dull, discoloured or chipped tableware. • • • • The level of salt is low, check the refill indicator. The cap of the salt container is loose. Your tap water is hard. Refer to "The water softener". Use salt and set regeneration of the water softener even when multi-functional tablets are used. Refer to "The water softener".
RATING PLATE INFORMATION FOR TEST INSTITUTES For all the necessary information for test performance, send an email to: info.test@dishwasher-production.com Write down the product number (PNC) that is on the rating plate. Mod. ... ... ... Prod. No. ... ... ... Ser. No. ... ENVIRONMENTAL CONCERNS with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office. Recycle materials with the symbol .
117873491-A-122018 WWW.ZANUSSI.