User manual

10
H
G
TŸranschlagwechsel
Bevor Sie nachstehende ArbeitsvorgŠnge
durchfŸhren, Netzstecker unbedingt aus der
Steckdose ziehen!
Den Wechsel auf folgende Weise ausfŸhren:
1. EntlŸftungsgitter (D) abnehmen.
2. Unteres Scharnier (E) mit Abdeckung (G)
abnehmen.
3. Untere TŸr vom mittleren Scharnier (H) abheben
und Scharnier abschrauben.
4. Obere TŸr vom oberen Stift (G) abnehmen.
5. Nachdem Sie die Stšpsel entternt haben, die auf
der gegenŸberliegenden Seite wieder
einzusetzen sind, nehmen Sie den oberen Stift
ab und montieren Sie ihn an der
gegenŸberliegenden Seite.
6. Obere TŸr wieder einsetzen. Mittleres Scharnier
an gegenŸberliegende Seite montieren.
7. Mit Hilfe eines 10 mm SchlŸssel den unteren
Scharnierstift abschrauben und auf
gegenŸberliegenden Scharnierseite wieder
anschrauben.
8. Untere TŸr wieder einsetzen.
9. Unteres Scharnier (E) auf gegenŸberliegende
TŸrseite montieren und mittels der vorher
entnommenen Schrauben befestigen. Abdeckung
(G) auf unteres Scharnier einsetzen. Abdeckung
(F) vom EntlŸftungsgitter (D) herausschieben und
auf gegenŸberliegende Seite montieren.
10.EntlŸftungsgitter wieder einsetzen.
Zur Ausrichtung der TŸren kann man auf das
mittlere Scharnier wirken.
Das mittlere Scharnier ist nach dem Lšsen der
beiden Schrauben mit Hilfe einer Vorrichtung
horizontal regulierbar.
Achtung
Vergewissern Sie sich nach AusfŸhrung des
Anschlagwechsels der TŸren, da§ alle
Schrauben fest angezogen sind und ŸberprŸfen
Sie auch, ob die Magnetdichtung am Mšbel
perfekt anliegt. Bei einer niedrigen
Raumtemperatur (z.B. im Winter) kann es
vorkommen, dass die Dichtung nicht perfekt am
Schrank haftet. Die Wiederherstellung der
Dichtung erfolgt automatisch nach gewisser
Zeit. Wollen Sie aber diesen Prozess
beschleunige, so genšgt es die Dichtung mit
einem Fšn zu erwŠrmen.
F
D
PR18
F
F
F
E
E
G
D419
39
CONTENTS
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Use / Cleaning the interior - Operation - Temperature regulation - Fresh food refrigeration - Freezing .
fresh food - Storage of frozen food - Thawing - Ice-cube production . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Use / Movable shelves -Positioning the door shelves - Freezing calendar . . . . . . . . . . . . . . . . . . . . . . .
Hints / Hints for refrigeration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Hints / Hints for freezing - Hints for storage of frozen food / Maintenance - Periodic cleaning . . . . . . . .
Periods of no operation - Interior light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Maintenance / Defrosting - Customer service and spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Installation - Location - Rear spacers - Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Installation Door Reversibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
speed up the thawing process other than those
recommended by the manufacturer. Never use
metal objects for cleaning your appliance as it
may get damaged.
Installation
¥ During normal operation, the condenser and
compressor at the back of the appliance heat up
considerably. For safety reasons, minimum
ventilation must be as shown in the instructions.
Attention: keep ventilation openings clear of
obstruction.
¥ Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Important: if the supply cord is damaged, it must
be replaced by a special cord or assembly availa-
ble from the manufacturer or its service agent.
¥ If the appliance is transported horizontally, it is
possible that the oil contained in the compressor
flows in the refrigerant circuit. It is advisable to
wait at least two hours before connecting the
appliance to allow the oil to flow back in the
compressor.
¥ There are working parts in this product which
heat up. Always ensure that there is adequate
ventilation as a failure to do this will result in
component failure and possible food loss. See
installation instructions.
¥ Parts which heat up should not be exposed.
Wherever possible the back of the product
should be against a wall.
Environment Protection
This appliance does not contain gasses which
could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The
appliance shall not be discarded together with
the urban refuse and rubbish. Avoid damaging
the cooling unit, especially at the rear near the
heat exchanger. Information on your local
disposal sites may be obtained from municipal
authorities. The materials used on this appliance
marked by the symbol are recyclable.