OPERATING AND INSTALLATION INSTRUCTIONS DUAL FUEL COOKER MODEL ZCM 5600
n ZCM 5600 c oit Introduction t This dual fuel cooker has been designed and manufactured to all the necessary British Standards. It also carries the C.E. mark. It is important that you understand how to use and care for the cooker properly before you use it for the first time. We have written this booklet with your safety in mind. Read the booklet thoroughly before you use the cooker. Keep the booklet in a safe place so that anyone who uses the cooker can read it.
Contents Page Lighting the cooker 4 The grill 7 The hotplate 10 The ovens 13 Oven cooking charts - Main fan oven 17 Roasting chart 20 - Second oven 21 Defrost feature 24 Things to note 25 The electronic timer 26 Care and cleaning 30 Installing the cooker 36 General information 38 What is wrong and why? 40 Service and spare parts 42 Customer care department 43 Guarantee conditions 44 Technical data 45 Safety requirements/ventilation 46 Location of appliance 46 Install
Lighting the cooker ZCM 5600 Lighting the cooker The system works by means of an electric spark system. Details about the plug are given on page 38. Hotplate To light 1. Lift up the lid. You cannot use the hotplate when the lid is down. 2. Push in the control knob and turn it to the the large flame symbol (highest setting), and press the ignition button immediately. When the burner has lit release the button.
Grill/second oven The grill and the second oven are operated by the same control so you cannot use them both at the same time. To light: 1 Open the door. 2 Push in the control knob and turn it to the large flame symbol (highest setting), and press the ignition button immediately. When the burner has lit release the button. GRILL 3 Leave the grill door open when you are using the grill. Warning: If the ignition button is not pressed immediately a build up of gas may cause the flame to spread.
Lighting the cooker ZCM 5600 To turn off any burner 1 Push in the control knob and turn it to the off position. This is shown by a large dot. GRILL FRONT LEFT For your safety When you are lighting any burner check that it has lit before you leave the cooker. When you are turning off a burner, do not leave the cooker until the flame has gone out. Main fan oven The main oven is an electric fan oven. To use the oven 1 Turn the oven control knob to the required setting.
The grill The grill is a high-speed grill. The instructions below tell you how to vary the heat setting and how to change the height of the grid to suit the food you are cooking. You should remember to turn the food regularly. You should not use the grill to keep food warm as it will continue to cook the food. For your safety You must keep the grill door open when the grill burner is lit. Accessible parts may be hot when the grill is used. Young children should be kept away.
The grill ZCM 5600 General Plate warming You can use the grill compartment to warm plates when you are using the oven. Preheating You don't usually need to preheat the grill. You may wish to preheat it for a couple of minutes when you are cooking steak or browning food. Positioning food on the grid Place food such as toast, tea-cakes and muffins towards the centre of the grid. If you put food outside this area it may require rotating during cooking.
The grill pan and handle The grill pan is supplied with a removable handle. To attach the handle, place the wirework under the cut out in the pan so that the metal plate hooks over the top of the grill pan. Slide the handle to the left and over the central bump on the grill pan. Ensure the handle is correctly located. It is not necessary to remove the grill pan handle during grilling. Place the grill pan on the shelf so that the pan is positioned centrally beneath the grill.
The hotplate ZCM 5600 The hotplate You can only use the hotplate when the lid is open. If you have any trouble lighting a hotplate burner turn all hotplate control knobs off and make sure the hotplate burner parts have been replaced correctly. See page 31for more information. Heat control The hotplate control knobs turn to the left from 'OFF' to 'HIGH' and then to 'LOW'. You can adjust the heat by turning the control between the highest and lowest settings.
For your safety 1 Take care to avoid burns and scalds when you are reaching across the hotplate. 2 Use pans with flat bases. They are more stable than pans which are warped. 3 Do not use pans with very heavy handles which cause the pan to tip. 4 Put pans on the centre of the burners. 5 Position pan handles so they cannot be accidentally knocked. 6 Take extra care when you are deep fat frying. Do not cover the pan with a lid. FRONT-LEFT Do not leave a pan unattended.
The hotplate ZCM 5600 Helpful hints 1 Keep flames under the base of pans. If the flames lick round the sides of the pans you are wasting gas. 2 Only heat the amount of liquid you need. Do not overfill pans. 3 Cover pans with a lid whenever possible. The food will heat up more quickly and there will be less steam in the kitchen. 4 Try cooking more than one vegetable in the same pan, for example potatoes and carrots. 5 Cut vegetables into smaller pieces. This way they will cook more quickly.
The fan oven Before you use the oven you should wipe it out with a damp cloth to remove any dust. The fan circulates hot air in the oven to give an even temperature throughout the oven. You can make use of the even temperature when you want to cook a large quantity of similar foods at the same time. For example, if you are cooking more than one tray of cakes or biscuits there is no need to swap the trays around during cooking. Preheating You do not need to preheat the oven when casseroling and so on.
The ovens ZCM 5600 Batch baking The fan oven cooks evenly on all shelf levels. This is especially useful when you want to batch bake on three shelves. Make sure the shelves are evenly spaced to get the best results. Oven shelves You can slot the oven shelves in any of five positions. When you are using more than one shelf, make sure the shelves are evenly spaced. For safety the shelf will only pull out so far.
The gas top oven Before you use the oven you should wipe it out with a damp cloth to remove any dust. You can only cook on one shelf at a time. You should turn food round during the cooking time. Preheating You do not need to preheat the top oven for casseroling and so on. Preheat the oven for baking or when you are cooking sensitive food such as Yorkshire puddings, soufflés and yeast mixtures. When you are cooking or reheating frozen or chilled food read the instructions on the packaging.
The ovens ZCM 5600 Helpful hints 1. Arrange the oven shelves in the required positions before switching the oven on. 2. Place dishes centrally on different shelves rather than cluster several dishes on one shelf. 3. When baking larger quantities of food, the shelf positions should be evenly spaced. A slight increase in cooking time may be necessary. 4. Do not place dishes or baking trays on the oven base as this may restrict the circulation of heat.
Oven Cooking Chart - Main fan oven The oven temperatures are intended as a guide only. It may be necessary to increase or decrease the temperatures by 10°C to sui t individual preferences and requirements. Shelf positions are not critical but ensure that oven shelves are evenly spaced when more than one is used.
Oven cooking chart Food Casseroles Cooking temp (°C) Beef/lamb Chicken 140 - 160 2½ - 3 h 180 - 190 1¼ - 1½ h Follow manufacturer's instructions 170 - 190 20 - 30 190 - 200 20 - 25 190 - 200 40 - 50 130 - 140 1½ - 2 h 190 - 200 40 - 45 190 - 200 30 - 35 170 - 180 20 - 30 210 - 220 25 - 40 190 - 200 15 - 20 190 - 210 25 - 35 180 - 210 25 - 45 150 - 160 1 - 1½ h 160 - 180 see roasting chart 210 - 220 8 - 10 190 - 200 30 - 40 170 - 180 20 - 30 ZCM 5600 18 Convenience Foods Fish Fish Pie (Potato Topped) F
Food Vegetables: Yorkshire Puddings: Approximate cooking time (m) 180 - 190 180 - 190 180 - 190 180 - 190 210 - 220 200 - 210 1 - 1½ h 1 - 1½ h 30-35 15-20 25-40 15-25 ZCM 5600 Baked Jacket Potatoes Roast Potatoes Stuffed Marrow Stuffed Tomatoes Large Individual Cooking temp (°C) Oven cooking chart
Roasting chart ZCM 5600 Roasting chart MEAT TEMPERATURE COOKING TIME Beef 160 - 180°C 20 - 35 min per ½kg/1lb and 20 - 35 min over Beef, boned 160 - 180°C 20 - 35 min per ½kg/1lb and 25 - 35 min over Mutton and Lamb 160 - 180°C 25 - 35 min per ½kg/1lb and 25 - 35 min over Pork and Veal 160 - 180°C 30 - 40 min per ½kg/1lb and 30 - 40 min over Ham 160 - 180°C 30 - 40 min per ½kg/1lb and 30 - 40 min over Chicken 160 - 180°C 15 - 20 min per ½kg/1lb and 20 min over Turkey and Goose 160 -
Oven cooking chart - Second oven These instructions are for cooking in the oven after it has been pre-heated for 20 minutes. The recommended shelf positions give the best results. Put the dishes centrally on the shelf and turn food round during the cooking time. You can change the gas marks and cooking times to suit your own tastes. It is important to check that food is piping hot before serving. If you are using both ovens at the same time you may need to adjust the cooking times.
Oven cooking chart Food Poultry: Chicken Gas mark 5 Duck and duckling 5 Shelf position Shelf on oven base Shelf on oven base Approximate cooking time 20 mins. per ½kg (1lb) and 20 mins. 25 mins. per ½kg (1lb). Stuffed poultry Pastries: Plate tart (shortcrust) Fruit pie (shortcrust) Mince pies (flan pastry) 6 6 5 2 2 2 25 - 35 mins. 25 - 35 mins. 15 - 25 mins. To help pastry brown on the underside cook on a metal plate, or if plates are flat and have no rim underneath, place on baking tray.
Food Puddings: Milk pudding Baked sponge pudding Baked custard Gas mark Shelf position Approximate cooking time 2 3 3 2 2 2 2 hrs. approx. 45 - 60 mins. 50 - 60 mins. Note: You must soak dried beans then boil them in an open pan for 15 minutes before you add them to any dish.
Defrost feature ZCM 5600 Defrost feature Uses of defrost feature This fan oven function defrosts most foods faster than more conventional methods. It is particularly suitable for delicate frozen foods which are to be served cold e.g. cream filled gateaux, cakes covered with icings or frostings, cheesecakes, biscuits, scones, etc. It is preferable to thaw fish, meat and poultry slowly in the fridge. However this process can be accelerated by using the defrost function.
Things to note When defrost is selected, the oven indicator neon may come ON. It will stay ON until the oven reaches room temperature and then go OFF. It may cycle ON and OFF periodically during defrosting to maintain a steady room temperature, inside the oven. Care must always be taken when handling foods in the home. Always follow the basic rules of food hygiene to prevent bacterial and microbial growth and cross contamination when defrosting, preparing, cooking, cooling and freezing foods.
The electronic timer ZCM 5600 The electronic timer Please note that this is a 24 hour clock, for example 2.00 pm is shown as 1400. Cookpot symbol Bell symbol In the following pages we explain how to set the controls. Read through them a few times until you are familiar with the procedure. We have supplied a plastic card as a quick reference when setting the timer.
When you are using the minute minder you can make the clock show the time of day by turning the selector knob to 'manual'. The bell symbol will stay on to remind you that the minute minder is set. At the end of the timed period an alarm will sound and the bell symbol will go out. Switch off the alarm by turning the selector knob to ' '. Then turn to 'manual' and the time of day will show in the display.
The electronic timer ZCM 5600 3 How long will the food take to cook? Turn the selector knob to 'cook time'. Then turn the setting knob until the length of time you want the food to cook shows in the display. The maximum cooking time is 10 hours. 'Auto' will show in the display. 4 What time do you want the food to be cooked by? Turn the selector knob to 'End time'. Turn the setting knob until the time the oven is to switch off shows in the display. The cookpot ( ) will go out.
Hints and tips for automatic cooking 1 Check the instructions for setting the automatic controls until you are familiar with the timer operation. 2 If the oven has been used, allow it to cool completely before using for automatic cooking. 3 You should leave food in the oven for as short a time as possible before automatic cooking starts. 4 Do not leave food to stand in the oven when it has finished cooking. You should remove it and if it is not going to be eaten at once, cool it quickly.
Care and cleaning ZCM 5600 Care and cleaning For your safety For hygiene and safety reasons you must keep this cooker clean. A build up of fat or other foodstuff could cause a fire. Try to mop up spills and splashes as soon as they happen. But be careful as parts of the cooker will be hot. Do not use any polishes, caustic cleaners, abrasives, washing soda or soap powder except those recommended in this booklet.
Clean the burner crowns by soaking them in very hot soapy water. You can remove any stubborn stains by scouring with a soap filled pad such as 'Brillo'. If you look after the burner crowns in this way they will stay reasonably clean. However the surface will dull with time. Aluminium based saucepans can leave shiny metal marks on the pan supports. Clean the pan supports regularly to remove the marks using a mild abrasive like 'Jif' with a soft scourer.
Care and cleaning ZCM 5600 The main fan oven The top, sides and back of your oven are coated in a special material which helps to keep itself clean. Follow these simple rules to maintain the appearance of the special finish. Do not overfill dishes or they will boil over. Do not put dishes too high in the oven. If you do they may stick to the oven roof. Cover your roasting tins with foil. This will prevent fat splashing. Use a roasting tin which is just large enough for the meat and potatoes.
Main oven cleaning cycle You need to follow the cycle to keep the inside of the oven in good condition. The type of cooking you do will affect how often you need to follow the cycle. If you do a lot of roasting and very little other baking you should follow the cleaning cycle once a week. If you do very little roasting you will only need to follow the cleaning cycle every 2-3 weeks. To carry out a cleaning cycle: 1. Remove the oven shelves. FAN OVEN 2.
Care and cleaning ZCM 5600 Top oven cleaning cycle 1. Remove the oven shelf. OVEN - GRILL 2. Set the oven to mark 5 for at least 30 minutes. OVEN - GRILL 3. Turn the temperature up to mark 7 for 2 hours or until the oven is presentably clean. Some staining will remain. Do not use any cleaning agents or scrapers on the inside of the oven. Do not wash the special finish. General Clean the base of the oven, the oven shelf and the oven door while they are still slightly warm.
Cleaning between the outer and inner door glass. You can remove the glass from the oven door if you need to. To remove the outer glass 1 Open the door so you can get at the two cross head screws on the top of the door. 2 Loosen these two screws using a pozidrive screwdriver. 3 You should hold the door glass securely in place with one hand, whilst removing the screws completely, with the other hand. If you do not do this, the door glass could fall forward.
Installation ZCM 5600 Installing the cooker For your safety This cooker must be installed and serviced by a competent person as stated in the Gas Safety (Installation & Use) regulations current editions and the IEE Wiring Regulations. It is important that the cooker is suitable for your gas supply. Your installer should check the data badge. Make sure that a stability bracket is fitted.
Positioning The diagram shows how close to the cooker cupboards, shelves, curtains and so on can be fitted. Look at the diagram and carefully read the instructions to make sure your cooker is fitted safely. If you are in doubt your installer will give you advice. This is a type X cooker which means it is free-standing and can be fitted with cabinets on one or both sides. Do not fit any materials which may catch fire, for example wood or curtains behind the cooker.
General information ZCM 5600 General information For your safety Do not block any of the cooker vents. Never line any part of the cooker with aluminium foil. Don't let items which can catch fire or electric mains leads such as kettle flexes trail over any part of the cooker. Moving your cooker You may damage some soft or badly fitted floor coverings when you move the cooker. The floor covering under the cooker should be securely fixed so it does not ruck up when you move the cooker across it.
If the ignition system doesn't work there may be a fault with the electrical supply. First, check the socket by trying out another piece of electrical equipment in it, if that works correctly renew the fuse in the plug. If the fuse keeps failing there is a fault in the cooker which must be put right. Do not use a fuse with a rating higher than 13 amps. Do not carry out other electrical work. Unplug the cooker and tell your installer.
What is wrong and why? ZCM 5600 What is wrong and why? We strongly recommend that you carry out the following checks on your cooker before calling a Service Engineer. Problem The grill or hotplate will not light. Check l l l If only the hotplate burners will not light make sure that the burner parts have been replaced correctly. See instructions on page 31. If you cannot hear any sparking when you press the ignition button there may be a fault with the electrical supply.
Problem The oven fan is noisy Check l l Check that the cooker is properly installed and is level. Check that shelves and bakeware are not vibrating in contact with the back panel in the oven. Problem The oven does not work Check l l l l Check that the clock is set for manual cooking. See page 26. Check that the cooker has been plugged in and switched on at the wall. Check that you have correctly followed the instructions for using the oven. See pages 5 and 6.
Service and spare parts ZCM 5600 Service and spare parts For your safety Maintenance work must only be done by a competent person. Do not try to repair the oven yourself. This could be dangerous. It is dangerous to alter or modify the product in any way. Help us to help you Please determine your type of enquiry before writing or telephoning. Service It is a recommendation by the manufacturer that your cooker has an annual gas safety check carried out by the manufacturers approved organisation.
Customer care department For general enquiries concerning your Zanussi cooker or further information on Cooking, Cooling or Washing products, you are invited to contact our Consumer Care Department by letter or telephone as follows: Customer Care Department Zanussi Zanussi House Hambridge Road Newbury Berkshire RG14 5EP Tel: (01635) 521313 The Gas Consumers' Council The Gas Consumers' Council (GCC) is an independent organisation which protects the interests of gas users.
ZCM 5600 Guarantee Conditions Standard guarantee conditions We, Zanussi, undertake that if within 12 months of the date of the purchase this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: The appliance has been correctly installed and used only on the electricity supply stated on the rating plate The appliance has been used
ZCM 5600 TECHNICAL DATA DIMENSIONS Height to hotplate Space for fixing at hotplate level Space for fixing above hotplate level Minimum space above hotplate Weight of appliance Minimum distance from rear wall Height 900mm (nominal) Width 600mm (nominal) Depth 600mm (to front of door panel) 2mm minimum clearance Flush-see important note 'Location of Appliance' page 45. 787mm (If a cooker hood is fitted refer to the cooker hood installation instructions). 64.5kg.
ZCM 5600 IMPORTANT - SAFETY REQUIREMENTS This appliance must be installed in accordance with the Gas Safety (Installation and Use) Regulations Current Editions and the I.E.E. Wiring Regulations. Detailed recommendations are contained in the following British Standard Codes of Practice - BS.6172, BS.5440: Part 2 and B.S.6891. All British Standards must be 'Current Editions'. PROVISION FOR VENTILATION This appliance is not connected to a combustion products evacuation device.
ZCM 5600 INSTALLATION 1. PARTS REQUIRED The loose hotplate parts are packed in the polystyrene fitment on top of the hotplate. 2. LEVELLING THE APPLIANCE If the appliance requires levelling or its height adjusting (from the hotplate to any working surface), the procedure below must be followed: 1. Adjustment to suit floor conditions or height is obtained by rotating clockwise or anticlockwise the feet, at the front and rear of the appliance. 2.
ZCM 5600 4. CONNECTING TO GAS 50 100 Fig.3 250 450 700 850 This appliance is designed to be installed with an appliance flexible connection only. Supply piping should not be less that R³/8. Connection is made to the Rc ½ (½" B.S.P.) female threaded entry pipe located just below the hotplate level on the rear left hand side of the appliance. NOTE: ONLY LIQUID SEALANTS TO BE USED WHEN INLET GAS PIPE IS FITTED TO SHUT OFF VALVE I.E.: DO NOT USE P.T.F.E. SEALANT TAPE.
ZCM 5600 If the wiring is extended or a completely new cable fitted a 3-pin 13 amp plug should be fitted. (See Fig.4a). Connect the GREEN AND YELLOW wires as follows: BROWN to the Live Terminal. BLUE to the Neutral Terminal. GREEN and YELLOW to the Earth Terminal.
ZCM 5600 10. CHECKING THE MAIN OVEN CONTROLS 1. 1a. 2. 3. 4. TO SET THE TIME OF DAY (see Fig.5) Turn on the electricity supply and ensure that the thermostat is in the off position. Before setting timer read important note below. Rotate the left hand clock knob to manual and back to the clock ' ' position. Set the time of day by rotating the right hand knob. Note that it is a 24 hour clock. Rotate the left hand clock knob back to the manual position. Fig.
PART NO: 311336506