FREEZER ZBF6124A INSTRUCTION BOOKLET 2223 520-51
IMPORTANT SAFETY INFORMATION It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety information. This information has been provided in the interest of safety.
At the end of the Appliance Life • When disposing of your appliance, use an authorised disposal site. • Remove the plug and ensure that any locks or catches are removed, to prevent young children being trapped inside. Disposal of old Appliances The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
OPERATION Control Panel A C D E B A- Pilot light - Green D- Fast freeze switch B- Thermostat control knob E- Alarm light - Red C- Fast freeze light - Amber Before using Start your appliance Remove all securing tapes. Wash inside the appliance with lukewarm water and bicarbonate of soda (5 ml to 0.5 litre of water). Insert the plug into the wall socket. The pilot light (A) will illuminate to show that the appliance is on. Do not use soap or detergent as the smell may linger. Dry thoroughly.
Freezing fresh food The 4-star compartment is suitable for long term storage of commercially frozen food, and for freezing fresh food. If the freezer has already been working for some time, press the Fast freeze switch at least 24 hours before introducing the food into the freezer in order to ensure better freezing results. Place the food to be frozen in the two top compartments. In order to freeze the quantity indicated on the rating plate, arrange the food directly in contact with the cooling surfaces.
HINTS AND TIPS Food Storage • Avoid unnecessary frosting in the cabinet by packing all foodstuffs into airtight packages before placing them in the freezer. To obtain the best performance from your freezer • Do not store warm food or evaporating liquids. • • Avoid buying frozen food if you cannot store it straight away. The use of an insulated container is advisable. When you arrive home place the frozen food in the freezer immediately.
MAINTENANCE AND CLEANING Before any maintenance or cleaning work is carried out, DISCONNECT the appliance from the ELECTRICITY supply. Remove the protection (A) by unscrewing both screws (B). Clean the protection and the bottom of the compartment. Internal cleaning After cleaning replace the protection and fix with both screws. Clean the inside and accessories with warm water and bicarbonate of soda (5ml to 0.5 litre of water). Rinse and dry thoroughly.
Defrosting When the frost has reached a thickness of up to 4mm it can be removed using the ice scraper provided with the appliance. During this operation it is not necessary to disconnect the appliance from the mains and remove the food. Never use metal tools for this operation. For complete defrosting (once or twice a year) proceed as follows: - turn the thermostat control knob to the «OFF» position (•) or disconnect the appliance from the mains.
SOMETHING NOT WORKING If the appliance is not working correctly, please carry out the following checks before contacting your local Service Force Centre Symptom Solution No power to the appliance Check there is power at the socket. Check there is not a power cut by checking the household lights. Check the fuse has not blown. The temperature in the freezer is too high Check the thermostat control knob on the top panel is turned to the correct setting relative to ambient conditions.
TECHNICAL SPECIFICATIONS DIMENSIONS Height 88 cm Width 56 cm Depth 55 cm POWER SUPPLY VOLTAGE AND FREQUENCY 230-240 V / 50 Hz TOTAL POWER ABSORBED 100 W AVERAGE DAILY UNITS ELECTRICITY * 0.570 kWh GROSS CAPACITY Freezer 110 l Freezer 94 l NET CAPACITY STAR RATING * This figure is based on standard test results in accordance with European Standard EN 153. Actual consumption will depend on how the appliance is used and where it is located.
Electrical connections Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. WARNING: THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should this safety measure not be observed. For replacement, use a 13amp BSI362 fuse. Only ASTA or BSI approved fuses should be used. The plug must not be used if the fuse cover/carrier is lost. The cover/carrier is indicated by the coloured insert at the base of the plug.
Door Reversibility The appliance is supplied with the door opening to the right. For door opening in the opposite direction, perform the following actions prior to installation 1. Unscrew the upper pin and remove the spacer 2. Remove the door. 3. Unscrew with a key the lower pin and replace it on the opposite side. 4. Reinsert the door, refit the spacer and rescrew the upper pin on the opposite side. min. 2 200 cm 50 mm Instructions for totally built-in appliances Building-in instructions min.
Fasten the appliance with 4 screws provided in the kit included with the appliance. I I Apply the sealing strip pushing it between the refrigerator and the adjacent cabinet. D724 From the plastic cover (E), which is used to cover the hinge with the pivot pin, you must take away the part as indicated in the drawing. This operation is made easer since there is, in the internal part of the cover hinge lid a groove that facilates the removal of this coomponent.
Separate parts Ha, Hb, Hc, Hd as shown in the figure. Ha Hb Hc Hd PR266 Place guide (Ha) on the inside part of the furniture door, up and down as shown in the figure and mark the position of external holes. After having drilled holes, fix the guide with the screws supplied. ca. 50 mm 90° 21 m m 90° ca. 50 mm 21 m m Fix cover (Hc) on guide (Ha) until it clips into place Ha Hc PR33 Open the appliance door and the furniture door at 90°. Insert the small square (Hb) into guide (Ha).
Remove the brackets and mark a distance of 8 mm from the outer edge of the door where the nail must be fitted (K). 8mm K Ha Place the small square on the guide again and fix it with the screws supplied. Should the lining up of the furniture door be necessary, use the clearance of slots. At the end of operations, it is necessary to check if the door of the furniture closes properly. Hb PR168 Fix cover (Hd) on guide (Hb) until it clips into place.
www.electrolux.com www.zanussi-electrolux.co.
