User Manual GETTING STARTED? EASY.
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
• • • Clean the appliance with a moist soft cloth. Only use neutral detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects. Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance. If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard.
• • • • Do not touch the compressor or the condenser. They are hot. Do not remove or touch items from the freezer compartment if your hands are wet or damp. Do not freeze again food that has been thawed. Obey the storage instructions on the packaging of frozen food. INTERNAL LIGHT • The type of lamp used for this appliance is not suitable for household room illumination CARE AND CLEANING WARNING! Risk of injury or damage to the appliance.
soap to remove the typical smell of a brand-new product, then dried thoroughly. CAUTION! Do not use detergents or abrasive powders, as these will damage the finish. POSITIONING THE DOOR SHELVES To permit storage of food packages of various sizes, the door shelves can be placed at different heights. 1. Gradually pull the shelf in the direction of the arrows until it comes free. 2. Reposition as required. 1 2 To freeze fresh foods it is not necessary to change the medium setting.
• A faint click noise from the temperature regulator when the compressor switches on or off. HINTS FOR ENERGY SAVING • Do not open the door frequently or leave it open longer than absolutely necessary.
PERIODIC CLEANING CAUTION! Do not pull, move or damage any pipes and/or cables inside the cabinet. CAUTION! Take care of not to damage the cooling system. CAUTION! When moving the cabinet, lift it by the front edge to avoid scratching the floor. The equipment has to be cleaned regularly: 1. Clean the inside and accessories with lukewarm water and some neutral soap. 2. Regularly check the door seals and wipe clean to ensure they are clean and free from debris. 3. Rinse and dry thoroughly. 4.
WARNING! If you want to keep the appliance switched on, ask somebody to check it once in a while to prevent the food inside from spoiling in case of a power failure. TROUBLESHOOTING WARNING! Refer to Safety chapters. WHAT TO DO IF... Problem Possible cause The appliance does not operate. The appliance is switched off. Switch on the appliance. The mains plug is not connected to the mains socket correctly. Connect the mains plug to the mains socket correctly. There is no voltage in the mains socket.
Problem Water flows inside the refrigerator. Possible cause Solution The water outlet is clogged. Clean the water outlet. Food products prevent that water flows into the water collector. Make sure that food products do not touch the rear plate. Water flows on the floor. The melting water outlet is not connected to the evaporative tray above the compressor. Attach the melting water outlet to the evaporative tray. The temperature in the appliance is too low/too high.
2. If necessary, adjust the door. Refer to assembly instructions. 3. If necessary, replace the defective door gaskets. Contact the Authorised Service Centre. INSTALLATION WARNING! Refer to Safety chapters. LOCATION Refer to the assembly instructions for the installation. To ensure best performance, install the appliance well away from sources of heat such as radiators, boilers, direct sunlight etc. Make sure that air can circulate freely around the back of the cabinet.
VENTILATION REQUIREMENTS The airflow behind the appliance must be sufficient. Make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. 5. Switch on the appliance. The appliance is supplied with a 13 amp fuse (B). In the event of having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used. 5 cm min. 200cm2 min. 200cm2 WARNING! A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard.
222372554-A-462015 WWW.ZANUSSI.
