EN User Manual Fridge Freezer ZBB27450SA
Contents Safety information Safety instructions Operation Daily Use Hints and tips 2 3 4 5 6 Care and cleaning Troubleshooting Technical information Installation 7 8 10 11 Subject to change without notice. Safety information Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference.
• • • • • • • Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer. Do not damage the refrigerant circuit. Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer. Do not use water spray and steam to clean the appliance. Clean the appliance with a moist soft cloth. Only use neutral detergents.
Use Care and cleaning WARNING! WARNING! Risk of injury, burns, electrical shock or fire. • • • • • • • • • • • • Do not change the specification of this appliance. Do not put electrical appliances (e.g. ice cream makers) in the appliance unless they are stated applicable by the manufacturer. Be careful not to cause damage to the refrigerant circuit. It contains isobutane (R600a), a natural gas with a high level of environmental compatibility. This gas is flammable.
1. Turn the Temperature regulator toward lower settings to obtain the minimum coldness. 2. Turn the Temperature regulator toward higher settings to obtain the maximum coldness. CAUTION! If the ambient temperature is high or the appliance is fully loaded, and the appliance is set to the lowest temperatures, it may run continuously causing frost to form on the rear wall. In this case the dial must be set to a higher temperature to allow automatic defrosting and therefore reduced energy consumption.
Ice-cube production This appliance is equipped with one or more trays for the production of ice-cubes. Do not use metallic instruments to remove the trays from the freezer. compartment let the appliance run at least 2 hours on the higher settings. If large quantities of food are to be stored, remove all drawers and baskets from appliance and place food on cooling shelves to obtain the best performance. 1. Fill these trays with water 2. Put the ice trays in the freezer compartment.
Hints for freezing • To help you make the most of the freezing process, here are some important hints: • • • • • • • • the maximum quantity of food which can be frozen in 24 hrs. is shown on the rating plate; the freezing process takes 24 hours.
1. Switch off the appliance, or pull out electrical plug from the wall socket. 2. Remove any stored food, wrap it in several layers of newspaper and put it in a cool place. WARNING! Do not touch frozen goods with wet hands. Hands can freeze to the goods. 3. Switch on the appliance. After three hours reload the previously removed food into the freezer compartment. Defrosting the freezer CAUTION! Never use sharp metal tools to scrape off frost from the evaporator as you could damage it.
Problem The appliance is noisy. Possible cause The appliance is not supported properly. The compressor operates contin- Temperature is set incorrectly. ually. Solution Check if the appliance stands stable. Refer to "Operation" chapter. Many food products were put in at the same time. Wait some hours and then check the temperature again. The room temperature is too high. Refer to climate class chart on the rating plate. Food products placed in the appliance were too warm.
Problem Possible cause There is no cold air circulation in the appliance. Solution Make sure that there is cold air circulation in the appliance. 2. Replace the lamp with one of the same power and shape, specifically designed for household appliances. (the maximum power is shown on the light bulb cover). 3. Reassemble the lamp cover. 4. Connect the plug to the mains socket. 5. Open the door. Make sure that the light comes on.
Installation WARNING! Refer to Safety chapters. Positioning This appliance can be installed in a dry, well ventilated indoor where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance: Climate class Ambient temperature SN +10°C to + 32°C N +16°C to + 32°C ST +16°C to + 38°C T +16°C to + 43°C Some functional problems might occur for some types of models when operating outside of that range.
letter “E“ or by the earth symbol or coloured green and yellow. 2. Connect the wire coloured blue to the terminal either marked with the letter “N“ or coloured black. 3. Connect the wire coloured brown to the terminal either marked with the “L“ or coloured red. 4. Check that no cut, or stray strands of wire is present and the cord clamp (E) is secure over the outer sheath. Make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. 5. Switch on the appliance.
Installing the appliance Make sure that the mains cable can move freely. I 1. If necessary cut the adhesive sealing strip and then apply it to the appliance as shown in figure. x x 2. Push the appliance in the direction of the arrows (1) until the upper gap cover stops against the kitchen furniture. 3. Push the appliance in the direction of the arrows (2) against the cupboard on the opposite side of the hinge. I 8. Remove the correct part from the hinge cover (E).
Ha Hb 8 mm K Ha Hc Hd a. Install the part (Ha) on the inner side of the kitchen furniture. ~50 mm 90o 16. Place the small square on the guide again and fix it with the screws supplied. 17. Align the kitchen furniture door and the appliance door by adjusting the part Hb. 21 mm 90o ~50 mm 21 mm b. Push the part (Hc) on the part (Ha). Ha Hb 18. Press the part (Hd) on the part (Hb). Hb Hc 14. Open the appliance door and the kitchen furniture door at an angle of 90°. a.
household waste. Return the product to your local recycling facility or contact your municipal office. www.zanussi.
222371023-A-472014 www.zanussi.
