User manual

16
14.die 3 Stšpsel (N) herausnehmen, die auf der
Querstrebe in den Bohrlšchern der
Scharnierschrauben eingesetzt sind und auf der
gegenŸberliegenden Seite wieder anbringen;
15.die Scheibe (P) vom oberen Zwischenscharnier
abnehmen, den Stift ausmontieren,
entgegengesetzt wieder montieren, indem die
Scheibe am Stift wieder aufgesetzt und alles auf
der gegenŸberliegenden Seite montiert wird;
16.die TŸr wieder montieren. Gešffnet lassen und
das obere Zwischenscharnier mit den beiden
Schrauben in den Innenlšchern befestigen;
17.Die TŸr schlie§en und die dritte Schraube im
Šu§eren Loch einschrauben.
18.Die Griffe abschrauben und auf der
gegenŸberliegenden Seite montieren, nachdem
die kleinen Stšpsel mit einem Setzeisen
durchbohrt wurden.
Die freibleibenden Lšcher mit den im Beipack
enthaltenen Stšpseln verschlie§en.
Achtung
Vergewissern Sie sich nach AusfŸhrung des
Anschlagwechsels der TŸren, da§ alle
Schrauben fest angezogen sind und ŸberprŸfen
Sie auch, ob die Magnetdichtung am Mšbel
perfekt anliegt. Bei einer niedrigen
Raumtemperatur (z.B. im Winter) kann es
vorkommen, dass die Dichtung nicht perfekt am
Schrank haftet. Die Wiederherstellung der
Dichtung erfolgt automatisch nach gewisser
Zeit. Wollen Sie aber diesen Prozess
beschleunige, so genšgt es die Dichtung mit
einem Fšn zu erwŠrmen.
D737
57
CONTENTS
Warnings 55
Fastening to the wall 56
Use 58
Cleaning the interior 58
Control panel 58
Use of the refrigerator - Operation 58
Temperature regulation 58
Air circulation 58
Fresh food refrigeration 59
Movable shelves 59
Positioning the door shelves 59
Use of the adjusting temperaure compartment 59
Use of the freezer - Starting 60
Temperature regulation 60
Quick-freezing 60
The temperature alarm light 60
Freezing fresh food 60
Storage of frozen food 60
Thawing 61
Ice tray support 61
Hints 62
hints for refrigeration 62
Hints for freezing 62
Hints for storage of frozen food 62
Maintenance 63
Periodic cleaning 63
Periods of no operation 63
Interior light 63
Defrosting 63
Customer service and spare parts 64
Technical information 65
Installation 65
Location 65
Electrical connection 66
Rear spacers 66
Reversing the doors 67
Guarantee 69
3. Repeat the operation with the drill (see figure).
For masonry walls:
4. Insert the 4 metal bushings and tighten the
screws.
5. Fasten the brackets horizontally in the lower set
of holes as illustrated in the figure after having
previously removed the screws.
6. Push the appliance towards the wall and turn the
brackets downwards 90¡. Make sure that the
lower part of the brackets is located between the
appliance and the plate.
7. Insert the second set of screws in the upper
holes and complete the fastening.
For buffer walls (for ex. in sheetrock):
4. Insert the bushings by screwing them into the
holes drilled previously.
5. Fasten the brackets horizontally in the lower set
of holes with the screws as illustrated in the
figure.
6. Push the appliance towards the wall and turn the
brackets downwards 90¡. Make sure that the
lower part of the brackets is located between the
appliance and the plate.
7. Tighten the screws previously loosened and
complete the fastening with the second set of
screws.
Once the appliance is fastened to wall, make sure
that it is stable.
D753
15 cm 15 cm
1,5 cm
200 cm
D743
90°