User Manual GETTING STARTED? EASY.
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
• • • • • • • • • – areas for communal use in blocks of flats or in launderettes. Do not exceed the maximum load of 8 kg (refer to the "Programme chart" chapter). The operating water pressure at the water entry point from the outlet connection must be between 0.5 bar (0.05 MPa) and 8 bar (0.8 MPa). The ventilation opening in the base must not be covered by a carpet, mat, or any floor covering.
ELECTRICAL CONNECTION WARNING! Risk of fire and electric shock. • • • • • • • • • • The appliance must be earthed. Always use a correctly installed shockproof socket. Make sure that the parameters on the rating plate are compatible with the electrical ratings of the mains power supply. Do not use multi-plug adapters and extension cables. Make sure not to cause damage to the mains plug and to the mains cable.
THE APPLIANCE IS EQUIPPED WITH ... A B C D E x4 x2 x1 x1 x1 F G H L x1 x2 x1 x1 x1 x2 UNPACKING WARNING! Use the gloves. WARNING! Remove all the packaging and the transit bolts before installing the appliance. 1. Put two polystyrene packaging elements on the floor under the appliance. WARNING! It is strongly recommended that this action is carries out by two persons. 2. Carefully put the appliance down on its rear side. Make sure not to damage the hoses. 3.
4. Return the appliance in vertical position and remove the socket polystyrene protection. 1 2 5. Remove the power supply cable and the drain hose from the hose holders. It is possible to see water flowing from the drain hose. This is due to the testing with water of the appliance in factory. 6. Remove the three bolts, the hose holders and plastic spacers by using the spanner supplied with the appliance. F 7. Close the holes with the plastic caps you find in the user manual bag.
If possible, install the appliance where the floor is more stable. POSITIONING AND LEVELLING 1. Install the appliance on a flat hard floor. WARNING! Make sure that carpets do not stop the air circulation below the appliance. Bring the appliance near the furniture recess before levelling it. For more details, refer to paragraph "Building in". 2. Loosen or tighten the feet to adjust the level.
The inlet hose 1. Remove the inlet hose from inside the drum. 2. To connect the water inlet hose towards the proper direction and with the proper inclination, check the position of the water tap before connecting it to the back of the appliance. Make sure the hose is nor kinked, squashed but neither tensed. 3. Connect the hose to the back of the appliance. Do not turn the inlet hose downwards, but turn it left or right depending on the position of your water tap. 4.
To a stand pipe with vent-hole Directly into a drain pipe at a height of not less than 60 cm (23.6”) and not more than 100 cm (39.3”). The end of the drain hose must always be ventilated , i.e. the inner diameter of the drain pipe (min. 40 mm min. 1.6”) must be larger than the external diameter of the drain hose. Ø 40 mm max.600 mm To a sink spigot Put the drain hose in the spigot and tighten it with the supplied cable tie L.
596 mm If hoses run behind the appliance, make sure that nothing closes the small recess indicated with the measures 50 x 50 mm. 553 mm 819 mm 50 mm 50 mm 140 mm 76 mm The appliance is also equipped with an adhesive sponge pad H that you can find inside the drum. Attach it on the top of the appliance where indicated in the drawing. When levelling the appliance under the furniture, DO NOT squeeze the sponge pad.
1. Remove the screws of the top cover on the rear of the appliance and install the anti-tilting device as shown in the drawing. ~10mm 2. Adjust the anti-tilting device so that the distance from the counter is 10mm. Loosen the nut counterclockwise with a 3mm wrench. Adjust the height and turn the nut clockwise to fix it. PREPARATION AND ASSEMBLY OF THE CUPBOARD DOOR The dimensions of the cupboard door should be: • width min. 595 - max. 598 mm; • thickness 16-22 mm.
Reversibility of the cupboard door Carry out the cupboard door reversibility before the appliance is built in completely. N If the cupboard door has to be opened from left to right, invert the position of the hinge supports M with the magnetic plate N and lower plate O. M O M N Make sure that the plate with magnet is on the upper position. O Cupboard door preparation For countersinking the door, it is recommended to call a professional. y x y 12 Align the cupboard door to the furniture correctly.
Set the position of the lower hole respecting dimensions and distances shown in the drawing (449 mm). Countersink the holes. 16-22 mm Ø 35 mm 449 mm 12,5 - 14 mm 22±1,5 mm 595-598 mm Hinges To mount the hinges it is necessary to drill two holes (dia. 35 mm, depth 12.5 - 14 mm depending on the depth of cupboard door) on the inner side of the door. The hinges will be fixed to the door by means of the four supplied screws A.
Counter-magnet The appliance is pre set for a magnetic closure. For a correct closure: 1. Position the screw C and the counter-magnet D on the magnetic plate N. Lean the cupboard door against the screw until it leaves a mark. 2. Open the cupboard door and screw the counter-magnet D (steel disk + rubber ring E) with the screw C in the inner side of the cupboard door, where the screw left the mark as described in the first step.
CONTROL PANEL CONTROL PANEL DESCRIPTION 1 2 11 The child lock option is set by holding pressed the relative button for at least 3 seconds. 1 Programme dial 2 Display 3 Delay Start touch button 4 Flextime touch button 5 Start/Pause touch button 6 Stains touch button and permanent Child Lock 10 9 8 3 4 7 5 6 7 Extra Rinse touch button 8 Prewash touch button 9 Spin reduction options touch button • Rinse Hold option • No spin option • Night option 10 Temp.
Door locked indicator. Delay start indicator. The digital indicator can show: • • Reset position ( ). Programme duration (e. g. • Delay time (e. g. • Cycle end ( • Warning code (e.g. • Error indicator ( ). ). ). ). ). Time Manager indicator. Anti-stain indicator. Extra Rinse indicator. Add garments indicator. it lights at the beginning of the washing phase, when it is still possible to pause the appliance and add more laundry. Child safety lock indicator. Drum clean indicator.
• • • Rinse Hold . The related indicator comes on. The final spin is not performed. The water of the last rinse is not drained out to prevent the fabrics from creasing. The washing programme ends with water in the drum. The door stays locked and the drum turns regularly to reduce creasing. You must drain the water to unlock the door. Use this option for people with allergies to detergent residues and with sensitive skin.
suitable for a full load of normally soiled garments. a quick cycle for a full load of lightly soiled garments. very quick cycle for a smaller lightly soiled load (max. half load recommended). the shortest cycle to freshen up a small amount of laundry. The Flextime is available only with the programmes in the table. Synthetics indicator Cottons Eco shows the default duration and dashes. Touch Flextime button to reduce the programme duration according to your needs.
Programme Reference Default tempera- spin speed Maximum ture Spin speed load Temperature range range (rpm) Programme description (Type of load and soil level) 1400 rpm (1400 400) 8 kg White cotton and fast-coloured cotton. Normal soil. The energy consumption decreases and the time of the washing programme is extended, ensuring good washing results. Synthetics 40 °C 60 °C - Cold 1200 rpm (1200 400) 3 kg Synthetic items or mixed fabric items. Normal soil.
Programme Reference Default tempera- spin speed Maximum ture Spin speed load Temperature range range (rpm) Programme description (Type of load and soil level) Duvet 40 °C 60 °C - Cold 900 rpm (900 400) Daily Wash 40 °C 60 °C - Cold 1200 rpm (1200 400) 3 kg Cottons and Synthetics. Short programme for lightly soiled daily laundry. Sport 30 °C 40 °C - Cold 1200 rpm (1200 400) 3 kg Mixed fabric sportswear. Light soil items or items to refresh.
Cottons Eco Synthetics Delicates Spin/Drain Rinse ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Machine Clean ■ ■ Duvet Daily Wash Flextime Delay Start Stains1) Prewash Extra Rinse Night ■ Easy Iron Mixed No spin Rinse Hold Spin Programme ■ ■ ■ Sport ■ ■ ■ Denim ■ ■ ■ Wool/ Handwash ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 1) This option is not available with temperature lower than 40
CHILD LOCK With this option you can prevent children from playing with the control panel. To activate/deactivate this option, hold down the Plus Steam button until on the display. The appliance will default to this option after you switch it off. The Child Lock function may not be available for a few seconds after switching the appliance on. comes on/goes off BEFORE FIRST USE 1. Make sure that the electrical power is available and the water tap is open. 2.
- Maximum level for quantity of liquid additives. - Flap for powder or liquid detergent. • Do not set the delay start function. 5. Measure out the detergent and the fabric conditioner. 6. Carefully close the detergent dispenser. Always follow the instructions that you find on the packaging of the detergent products, but we recommend that you do not exceed the maximum indicated level ( ). This quantity will however guarantee the best washing results.
STARTING A PROGRAMME WITH THE DELAY START 1. Touch the Delay Start button repeatedly until the display shows the desired delay time. On the display the indicator shows . 2. Touch the Start/Pause button. The appliance door locks and starts the countdown of the delay start. The display shows the indicator . When the countdown is completed, the programme starts automatically. Cancelling the delay start after the countdown has started To cancel the delay start: 1.
If the AutoAdjust System has completed and the water filling has already started, the new programme starts without repeating the AutoAdjust System. The water and the detergent are not drained out in order to avoid waste. The display shows the maximum duration of the programme, updating it about 20 minutes after the starting of the new programme. There is also an alternative way of cancelling: 1. Rotate the selector knob to the "Reset" position . 2. 3. 4. 5.
The display shows the end of the last programme. Turn the programme dial to set a new cycle. If you set a programme or an option that ends with water in the drum, the Stand-by function doesn't deactivate the appliance to remind you to drain the water. , the If the dial is rotated to the "Reset" position appliance automatically turns off in 30 seconds. HINTS AND TIPS WARNING! Refer to Safety chapters. THE LAUNDRY LOAD • Divide the laundry into: white, coloured, synthetics, delicates and wool.
• • • Always start a washing programme with the maximum load of laundry allowed. If you pre-treat the stains or use a stain remover, set a programme with a low temperature. To use the correct quantity of detergent, check the water hardness of your domestic system. Refer to "Water hardness". WATER HARDNESS If the water hardness in your area is high or moderate, we recommend that you use a water softener for washing machines.
Use a small brush to clean the recess. Occasionally, at the end of a cycle the display may show the icon : this is a recommendation to perform the “drum cleaning”. Once the drum cleaning has been performed, the icon disappears. CLEANING THE DETERGENT DISPENSER To prevent possible deposits of dried detergent or clotted fabric softener and/or formation of mould in the detergent dispenser drawer, once in a while carry out the following cleaning procedure: 1. Open the drawer.
1. Open the pump cover. 2 1 2. Place a suitable bowl below the drain pump access to collect the water that flows out. Always keep a rag nearby to dry up any water spillages when removing the filter. 180˚ 3. Turn the filter 180 degrees in anti-clockwise direction to open it, without removing. Let the water flow out. 4. When the bowl is full of water, turn the filter back and empty the container. 5. Repeat the steps 4 and 5 until the water stops to flow out. 1 6.
7. If it is necessary, remove fluff and objects from the filter recess. Make sure that the impeller of the pump can rotate. If it does not rotate, contact the Authorised Service Centre. 8. Clean the filter under the water tap. 2 9. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages. 1 2 10. Close the pump cover.
CLEANING THE INLET HOSE AND THE VALVE FILTER 1 2 3 45° 20° EMERGENCY DRAIN If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain pump' paragraph. If necessary, clean the pump. When you drain the water with the emergency drain procedure, you must activate the drain system again: 1. Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water. 1. Disconnect the mains plug from the mains socket.
First try to find a solution to the problem (refer to the table). If the problem persists, contact the Authorised Service Centre. WARNING! Deactivate the appliance before carrying out any check. In case of major problems, the acoustic signals operate, the display shows an alarm code and the Start/Pause • • • button may flash continuously: - The mains supply is unstable. Wait until the mains supply is stable. - No communication between electronic elements of the appliance.
Problem Possible solution • • Make sure that the water tap is open. Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. Make sure that the water tap is not clogged. Make sure that the inlet hose has no kinks, damages or bends. Make sure that the connection of the water inlet hose is correct. Make sure that the filter of the inlet hose and the filter of the valve are not clogged. Refer to 'Care and cleaning'.
Problem Possible solution • The AutoAdjust System is able to adjust the programme duration according to the type and the laundry load size. Refer to "The AutoAdjust System load detection" in "Daily Use" chapter. • • • • Increase the detergent quantity or use a different detergent. Use special products to remove the stubborn stains before you wash the laundry. Make sure that you set the correct temperature. Decrease the laundry load. Too much foam in the drum during the washing cycle.
CONSUMPTION VALUES Stated values are obtained in laboratory conditions with relevant standards. Different causes can change the data: the quantity and type of laundry and ambient temperature. Water pressure, the supply voltage and the temperature of inlet water may also affect the washing programme duration. Technical specifications may be changed without prior notice to improve the quality of product.
TECHNICAL DATA Dimension Width/ Height/ Depth/ Total depth 596 mm/ 819 mm/ 540 mm/ 553 mm Electrical connection Voltage Overall power Fuse Frequency 230-240 V 2000 W 13 A 50 Hz Level of protection against ingress of solid particles and moisture ensured by the protective cover, except where the low voltage equipment has no protection against moisture IPX4 Water supply pressure 0.5 bar (0.05 MPa) 8 bar (0.
Power consumption of the off-mode in W 0.30 Power consumption in left-on mode in W 0.30 Water consumption in litres per year, based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and partial load. Actual water consumption will depend on how the appliance is used.
157020000-C-432018 WWW.ZANUSSI.
