ZANUSSI WASHING MACHINE TE 1025 V Instructions manual 146 6859 00 - 08/04
CONTENTS FOR THE USER ...............................................3 FOR THE INSTALLER .................................. 13 Warnings..........................................................3 Usage .........................................................3 Precautions against frost ............................3 Scrapping ....................................................3 Protection of the environment .....................3 Warnings ......................................................
A. FOR THE USER 1. WARNINGS Keep this user’s manual with your washing machine. If you sell your washing machine or give it away, make sure that it is accompanied by its user’s manual. The new user can then be informed of how the washing machine operates and read relevant warnings. These warnings have been written for your safety and for the safety of others. Please read these comments carefully before installing and using your washing machine. Thank you for your attention. 1.1.
2. WASHING MACHINE DESCRIPTION 1 2 1 - Control panel 2 - Lid opening handle 3 - Leveling screws 4 - Filter door 5 - Lever for moving the washing machine 4 5 3 2.1. The detergents dispenser Symbols 1 2 3 1 - prewash 3 - softener (do not exceed the MAX mark) 2 - wash 4 - softener overflow (if overfilled) 4 2.2.
3. HOW TO DO A WASH ? 3.5. Choice of the required option Before the first wash in your washing machine, we recommend that you should do a preliminary wash at 90°C with detergent but without any washing to clean the tub. The various options should be chosen after the programme has been displayed and before pressing the Start/ Pause pushbutton. 3.1. Loading the washing • • • Lift the machine cover. Open the drum by pressing on the locking button A; the two flaps automatically separate.
3.7.2. Modifying the current programme Before modifying the current programme, you must put the washing machine to pause by pressing on the «Start/Pause» pushbutton. If it is impossible to make the modification, the corresponding light flashes for few seconds. If you decide to change the programme in any case, you will need to cancel the current programme (see below). 3.7.3.
4. PROGRAMS TABLE The following does not show all possibilities, but simply the most frequent settings. Program Washing type Load Possible options 5,0 kg Tempera-tures Approximate consumptions °C liters kWh min 60 58 1,30 120-130 95 74 2,30 165-175 40 58 0,65 115-125 30 58 0,35 110-120 E 60 (*) 44 0,95 140-150 50 57 0,90 85-95 40 52 0,60 65-75 Cotton White or color, for example normally dirty work clothes, bed linen, table linen, underwear, towels.
5. WASHING GUIDE 5.3. Detergents and additives Only use detergents and additives suitable for use in a washing machine. Read the manufacturer's instructions and respect sections 2 and 4.2. 5.1.
5.4.
6. CARE AND CLEANING 6.4. The drain filter Do not do any cleaning operation until you have unplugged the washing machine. Clean the filter at the bottom of the washing machine regularly. The "filter"* light comes on if the filter is blo-cked. In this case clean it immediately. If you wash washing that is very fluffy, clean it after each wash. 6.1. Descaling the washing machine Normally there is no need to descale the washing machine if the detergent was correctly proportioned.
7. OPERATING PROBLEMS Many checks have been carried out during the manufacture of your washing machine. However, if you face a problem with its operation, please read the following sections before calling the After Sales service.
Symptom Cause The «DRUM POSITIONNING»* light** is not on at the end of the cycle: • the drum could not reach the right position due to a persistent unbalanced mass; turn the drum manually. flashes 4 times***: • the cover is not correctly closed. The «End»* light ** flashes 2 times***: • • • • • the drain filter is blocked, the drain pipe is blocked or kinked, the drain pipe is too high (see «installation»), the drain pump is blocked, the installation siphon is blocked.
B. FOR THE INSTALLER 1. WARNINGS • • • • • • This washing machine is heavy. Take care when moving it. You must remove the packing on the washing machine before use. Failure to remove all transport protection devices can cause damage to the washing machine or nearby furniture. The washing machine must be unplugged while packing is being removed. Do not allow any one other than a qualified plumber to make the hydraulic connections necessary to install your washing machine.
3. INSTALLATION If you want to keep your washing machine aligned with the adjacent furniture, you can cut the pipe support strip at the back of your washing machine. Leave the two side closers in place. 3.1. Unpacking Packing used to protect internal parts of the washing machine during transport must be removed before the washing machine is put into service for the first time. 3.2. Position Remove all packing from the washing machine.
- Connect the feed hose connector onto the water inlet tap, taking care to position the gasket correctly. - Turn on the water inlet tap. The water inlet hose cannot be extended. If it is too short, please contact the After Sales Department. 3.6. Drainage - Assemble the hose holder onto the drain hose. - Place the assembly in a drainage pipe (or in a sink) at a height between 70 and 100 cm. Make sure that it will not fall out.
From the Electrolux Group. The world’s No.1 Choice. The Electrolux Group is the world largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vaccum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
