User manual

ManualsBrandsZanussi ManualsDomestic AppliancesPX64

Commissioning

When the hob has been fully installed it will be

necessary to check the minimum flame setting. To do

this, follow the procedure below.

- Turn the gas tap to the MAX position and ignite.

- Set the gas tap to the MIN flame position then turn

the control knob from MIN to MAX several times.

If the flame is unstable or is extinguished follow the

procedure below.

Procedure:

Re-ignite the burner and set to MIN.

Remove the control knob, insert a thin

bladed screwdriver down the hole in the

front panel and turn the adjustment screw

until the flame is steady and does not

extinguish, when the knob is turned from

MIN to MAX. Repeat this procedure for all

burners.

Technical Maintenance

Check at regular intervals the condition and

serviceability of the gas connection hose and pressure

regulator, if any is fitted; in case of malfunction, do

not repair but replace the whole faulty part.

To ensure a smooth and safe operation, it is necessary

to periodically grease the gas taps.

Summary of content (13 pages)

PAGE 1
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: F Re-ignite the burner and set to MIN.
PAGE 2
Electrical connections Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This appliance is designed to be connected to a 230 V 50Hz AC electrical supply.
PAGE 3
Fitting the hob to the worktop Carry out the building in of the hob as follows: put the seals supplied with the hob, on the edges of the cut out, as shown in the diagram, taking care that the seals meet without overlapping; place the hob in the cut out, taking care that it is centred; fix the hob with the relevant fixing clamps and screws, as shown in the diagram. When the screws have been tightened, the excess seal can be removed.
PAGE 4
Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface.
PAGE 5
Installation IMPORTANT This appliance must be installed by qualified personnel. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. Gas Connection On the end of the shaft (A) , which includes the GJ 1/ 2" threaded elbow, an adjustable joint is fixed so that the washer (B) is fitted between the components as shown in the diagram.
PAGE 6
Instructions for the Installer Engineer technical data Supply Connections OVERALL DIMENSIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Width: Depth: Height: Weight: 580 mm. 510 mm. 84 mm. 11 Kg. Electric: 230 V 50Hz supply, 3 core flexible cable with non rewireable plug. CUT OUT DIMENSIONS Appliance Gas supply: LPG 30 mbar Width: 560 mm. Depth: 480 mm. Thickness: 30 mm. Appliance Class: 3 Appliance category: I 3 Burner Nominal Power LPG (Butane "A") Diameter Tap.
PAGE 7
Something Not Working? If the appliance is not working correctly, please carry out the following checks before contacting your local Service Centre. SYMPTOM n There is no spark when lighting the gas SOLUTION u Check that the unit is plugged in and the electrical supply is switched on. u Check the mains fuse has not blown. u Check the burner cap and crown have been replaced correctly, e.g. after cleaning.
PAGE 8
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added.
PAGE 9
Operation i This hob is provided with a safety device, which will stop the gas flow if the flame accidentally goes off during cooking. To light a burner, turn the relevant control knob anticlockwise to maximum position and push it down to ignite. Keep the control knob pressed down for about 5 seconds, to allow the safety device to be switched off. Then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again.
PAGE 10
Description of the Hob 2 3 3 1 5 1. 2. 3. 4. 5. 6. 7. 8. 6 7 4 8 Hob Top Auxiliary Burner Semi-rapid Burners Powered Rapid Burner Control knob for front left burner (auxiliary) Control knob for back left burner (semi-rapid) Control knob for back right burner (semi-rapid) Control knob for front right burner (powered rapid) INSTALLATION Any gas installation must be carried out by qualified personnel, and in accordance with existing rules and regulations.
PAGE 11
Contents For the User For the Installer Description of the Hob Page 5 Technical Data Page Operation Page 6 Installation Page 1 0 Maintenance and Cleaning Gas Connection Page 1 0 Page 7 Building In Page 1 1 Something Not Working Page 8 Fitting the Hob to the Worktop Page 12 Electrical Connection Page 1 3 Commissioning Page 1 4 9 Technical Maintenance Page 1 4 Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: S
PAGE 12
Important Safety Information You MUST read these warnings carefully before installing or using the appliance. Installation l l l l This appliance must be installed by qualified personnel, according to the manufacturers instructions and to the rules in force. l Remove all packaging before using the appliance. l Ensure that the gas and electrical supply complies with the type stated on the rating plate, located near the gas supply pipe. l Do not attempt to modify the appliance in any way.
PAGE 13
GAS HOB MODELS PW 64 PN 64 PX 64 PTDF 64 2 INSTRUCTION BOOKLET