User manual

ManualsBrandsZanussi ManualsDomestic AppliancesPIANO X KIT ZXL638IW

• This appliance has been designed to be operated by

adults and children under supervision. Young children

MUST NOT be allowed to tamper with the controls or

play near or with the oven.

• This appliance has been designed for cooking

edible foodstuff and to be used for domestic non-

professional purposes only. It must not be used for

any other purpose.

• It is dangerous to alter the specification in any way.

• For hygiene and safety reasons, this appliance should

be kept clean at all times. A build-up of fats or other

foodstuff could result in a fire.

• Accessible parts of this appliance may become hot

when it is in use. Children should be KEPT AWAY until

it has cooled.

• Under no circumstances should you attempt to repair

the appliance yourself. Repairs carried out by

unexperienced persons may cause injury or serious

malfunctioning. Refer to your local Zanussi Service

Centre. Always insist on genuine Zanussi spare

parts.

• Ensure that all control knobs are in the OFF position

when not in use.

• Should you connect any electrical tool to a plug near

this cooking appliance, ensure that electric cables

are not in contact with it and keep them far enough

from the heated parts of this appliance.

• If the appliance is out of order, disconnect it from the

electric supply.

This appliance complies with the following

E.E.C. Directives:

- 73/23 - 90/683 (Low Voltage Directive);

- 89/336

(Electromagnetical Compatibility Directive);

- 90/396 (Gas Appliances)

- 93/68 (General Directives)

and subsequent modifications.

During Operation

About Installation, Cleaning

and Manteinance

• It is mandatory that all operations required for the

installation are carried out by a qualified or competent

person, in accordance with existing rules and

regulations.

• Disconnect the appliance from the electrical supply,

before carrying out any cleaning or manteinance

work.

• Ensure a good ventilation around the appliance. A

poor air supply could cause lack of oxygen.

• Ensure that the gas supply complies with the gas

type stated on the identification label, placed near

the gas supply pipe.

• Using a gas cooking appliance will produce heat

and moisture in the room which it has been

installed in. Ensure a continuous air supply,

keeping the air vents in good conditions or

installing a cooker hood with discharge tube.

• In case of intensive or long time use of the

appliance, make the ventilation more efficient,

by opening a window or increasing the electric

exhaust fan power.

• Once you removed all packaging from the appliance,

ensure that it is not damaged and the electric cable

is in perfect conditions. Otherwise, contact your

dealer before proceeding with the installation.

• The manufacturer disclaims any responsability

should all the safety measures not be carried

out.

☛

MANUFACTURER:

ELECTROLUX ZANUSSI ELETTRODOMESTICI S.p.A.

Viale Bologna 298 - 47100 FORLI’ (Italy)

For Your Safety

These warnings are provided in the interest of safety. You MUST read them carefully before

installing or using the appliance.

It is most important that this instruction book should be retained with the appliance for future

reference. Should the appliance be sold or transferred, always ensure that the book is left with

the appliance in order that the new owner can get to know the functions of the appliance and

the relevant warnings.

Summary of content (10 pages)

PAGE 1
☛ For Your Safety These warnings are provided in the interest of safety. You installing or using the appliance. MUST read them carefully before It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred, always ensure that the book is left with the appliance in order that the new owner can get to know the functions of the appliance and the relevant warnings.
PAGE 2
Contents 1. Instruction for the User ............. Page 3 5. Instruction for the Installer ....... Page 6 2. Cleaning and Maintenance ....... Page 5 6. Electrical Connection ................ Page 7 3. Service - Spare parts ................. Page. 5 7. Adaptation to different types of gas................................ Page 8 4. Technical Data ........................... Page 6 8. Building In .................................. Page 9 1.
PAGE 3
POTTERY HOTPLATES Remember that a wide-bottomed pan allows a faster cooking than a narrow one. Always use pots which properly fit what you have to cook. Particularly make sure that the pans are not too small for liquids, since these could easily overflow. Moreover, the pans should not be too large for a faster cooking. In fact, grease and juices may spread on the bottom and burn easily. It is better to use non-openable moulds for baking cakes.
PAGE 4
2. Cleaning and Maintenance • Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. Wash the enamelled components with warm soapy water. Never use abrasive cleaners Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food. Carefully wash the stainless steel components with water, then wipe them dry with a soft cloth. The pan supports are dishwasher proof.
PAGE 5
4. Technical Data Gas Burners Rating Rapid (Double Crown) Auxiliary (small) Semirapid (medium) Category Setting Gas connection 3,5 kW 1 kW Electric Supply 2 kW HOB RECESS DIMENSIONS 230 V 50 Hz II 2H3+ L.P.G. 28-30/37 mbar G 1/2" Length 560 mm.(60 cm hob) - 830 mm.(90 cm hob) Width 480 mm. 5. Instruction for the Installer ● The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top.
PAGE 6
. Electrical Connection The appliance is designed to be connected to 230 V ~ 50 Hz electricity supply. The connection must be carried out in compliance with the laws and regulations in force.
PAGE 7
. Adaptation to different types of gas INJECTORS REPLACEMENT • Remove the pan supports. • Remove the burner's caps and crowns. • With a socket spanner 7 unscrew and remove the injectors (Fig. 6), and replace them with the ones required for the type of gas in use (see table 2). • Reassemble the parts, following the same procedure backwards. • Replace the rating label (placed near the gas supply pipe) with the relevant one for the new type of gas supply.
PAGE 8
. Building In A = Auxiliary burner SR = Semirapid burner R = Rapid Burner (Double crown) These hobs can be inserted in a built-in kitchen unit whose depth is between 550 and 600 mm. The hobs dimensions are shown in Figures 8 to 11. R A SR 500 SR 500 SR A R 580 580 FO 0941 FO 0940 Fig. 9 Fig. 8 SR R A SR SR R A 500 500 SR 860 860 FO 0245 FO 0244 Fig. 10 Fig.
PAGE 9
in. INSTALLATION AND ASSEMBLY 30 480 55 m These hobs can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in Fig. 12 and 13. The edge of the cut out must have a minimum distance from the rear wall of 55 mm. If there are side walls, or sides of the furniture unit near the hob, the cut out edges must have a minimum distance of 100 mm. 560 Carry out the building in of the hob as follows: • put the relevant sealings, supplied with the hob, on FO 2138 Fig.
PAGE 10
Fig. 16 Fig. 15 Kitchen unit with door a 60 591 20 min 30 Proper arrangements must be taken in designing the forniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in Fig. 15. The panel fitted under the hob should be easily removable to allow an easy access if a technical assistance intervention is needed.