Operating instructions

ManualsBrandsZanussi ManualsKitchen AppliancesMC19 M

33300 RF Module M-G1 HoTT SD

mc-19/19s and mc-22s

GRAUPNER GmbH & Co. KG – Postfach 1242 – 73230 Kirchheim/Teck – www.graupner.de

CONTENT:

1. Introduction..............................................................................................................01

2. Preparing the systems.............................................................................................01

3. Connection...................................................................................................01

4. Assembly...................................................................................................02

5. General Note..............................................................................................................04

5.1. Transmitter Display (TX Display)................................................................................04

5.2. Receiver Display.........................................................................................................06

5.2.1. Receiver Data View (RX DATAVIEW).........................................................................06

5.2.2. Servo Data (RX SERVO)............................................................................................07

5.2.3. Failsafe Setup (RX FAILSAFE)..................................................................................08

5.2.4. Mixer Setup (RX FREE MIXER - WING MIXER)......................................................10

5.2.5. Expo functions (RX CURVE)......................................................................................11

5.2.6. Servo test (RX SERVOTEST)....................................................................................12

6. Functions.....................................................................................................14

6.1. Binding.............................................................................................................14

6.1.1.Binding multiple receivers in one model...................................................................14

6.2. Range checking..........................................................................................................14

6.3. Fail Safe Function .......................................................................................................15

6.4. Country setting...........................................................................................................16

6.5. Low voltage warning..................................................................................................16

6.6. Range warning...........................................................................................................16

6.7. DATA socket...............................................................................................................16

6.8. Data storage...............................................................................................................17

6.9. Earphone socket.........................................................................................................17

7. Firmware Updates....................................................................................................18

7.1. Update process..........................................................................................................18

8. Warranty....................................................................................................22

Summary of content (24 pages)

PAGE 1
33300 RF Module M-G1 HoTT SD mc-19/19s and mc-22s CONTENT: 1. Introduction..............................................................................................................01 2. Preparing the systems.............................................................................................01 3. Connection...................................................................................................01 4. Assembly..............................................................................
PAGE 2
Manual Module M-G1 Order-No. 33300 These operating instructions are part of this product. They contains important notes to the operation and handling. Please take this into consideration when you pass on the product to third parties. Neglect of the operating instructions and the safety instructions lead to expiring the warranty. Graupner constantly work on the advancement of all remote control systems; changes of the scope of delivery in form, technology and equipment we must reserve ourselves therefore.
PAGE 3
4. ASSEMBLY: 1 4 X 1 3  4 2 Fig. 2 Fig. 1   Fig. 3 Fig. 4  Manual Module M-G1 33300 Fig. 5 Fig. 6 Fig. 7 Fig.
PAGE 4
  2 1 Fig. 9 Fig. 10 Fig. 11 1. Position the aerial lead and the blue four-pin module plug as shown in Fig. 6. 2. Fig. 7 shows the white rectangular socket for the module plug, and the circular aerial socket. 3. Press the four-pin module plug into the socket on the module using light pressure. The connector system is polarised: note the lateral lugs. Ensure that it engages fully (arrows), so that there is no chance of it working loose in operation (Fig. 8). 4.
PAGE 5
. GENERAL NOTE When switching on or adjusting the radio control system it is essential to keep the transmitter aerial at least 15 cm away from the receiver aerials at all times. If the transmitter aerial is too close to the receiver aerials, the receiver will be overloaded, causing the red LED on the receiver to light up. The transmitter responds by emitting a beep once every second; the red LED also goes out. The radio control system is now in Fail-Safe mode.
PAGE 6
Transmitter low-voltage warning (ALARM VOLT): you can adjust the low voltage threshold at which the alarm (continuous beeping) is triggered; the available range is 4 - 15 V. When the alarm is triggered, “VOLT-E” flashes at top right in the SMART-BOX transmitter display, and the parameters ACTION VOLT and ALARM VOLT are displayed in inverse form.
PAGE 7
5.2. RECEIVER DISPLAY 5.2.1 Receiver Data View (RX DATAVIEW) If you wish to switch to the receiver data display, press the ENTER button repeatedly until RX DATAVIEW appears on the screen. Please note: menus 3.2.1 to 3.2.6 can only be selected when the receiver is RX DATAVIEW > S-QUA 100% S-dBm -49dBm switched on. When you switch the receiver on, it may take a few seconds befoS-STR 065% R-TEM.
PAGE 8
The limit values for receiver temperature which trigger a warning can be set in the RX SERVO TEST display under ALARM TEMP+ (50 – 80°C) and ALARM TEMP- (-20 – +10°C). If the receiver temperature rises above the maximum value or falls below the minimum, the unit generates an audible warning (continuous beeping). At the same time all the Smartbox receiver displays show a flashing “TEMP.E” at top right, and the parameter R-TEM is shown in inverse form in the receiver data display (RX DATAVIEW).
PAGE 9
Channel select (OUTPUT CH): here you select the desired channel; the remainder of the settings in this display only affect the channel which you select at this point. Servo reverse (REVERSE): sests the direction of rotation of the connected servo Normal: REVERSE OFF Reverse: REVERSE ON Servo centre (CENTER): The “CENTRE” line displays the current pulse width in μs of the control channel selected in the “OUTPUT CH” line.
PAGE 10
features two servos acting on each aileron instead of only one. The SMART-BOX can be used to manage a maximum of sixteen transmitter channels. At this point you can define how the transmitter channels (INPUT) are assigned to the channels (OUTPUT) of the receiver(s). If your model is fitted with multiple receivers, the Master receiver is the last receiver to be bound. However, in subsequent operations only the receiver which was bound last is able to make a telemetry connection to the transmitter.
PAGE 11
Safe behaviour of the three servos connected to control channel 4, regardless of the individual settings of the OUTPUT CH for INPUT CH 04. This also applies, for example, if it is mapped in turn to INPUT CH 01. In this case servo socket 04 would respond in accordance with the Fail-Safe settings for CH 01. In contrast, the response or delay time set in the “DELAY” line always applies uniformly to all channels which are set to “FAIL-SAFE”.
PAGE 12
aileron and elevator functions. 5.2.5 Expo Functios (RX CURVE) To switch to the Expo functions display, press the ENTER button repeatedly until RX CURVE appears on the screen.
PAGE 13
5.2.6 Servo test (RX SERVO TEST) To switch to the Servo test display, press the ENTER button repeatedly until RX SERVO TEST appears on the screen ENTER ESC RX SERVO TEST < ALL-MAX : 2000usec ALL-MIN : 1000usec TEST : STOP ALARM VOLT : 3.8V ALARM TEMP+ : 70°C ALARM TEMP- : 10°C CH OUTPUT TYPE: ONCE INC + DEC INC + DEC RX SERVO TEST < ALL-MAX : 2000usec ALL-MIN : 1000usec TEST : STOP ALARM VOLT : 3.
PAGE 14
SERVO display under the menu point ‘PERIOD’. SAME: the receiver outputs are transmitted in parallel blocks of four, i.e. channels 1 to 4 and channels 5 to 8 receive the transmitter signal simultaneously in each case: recommended for digital servos. It is particularly useful where multiple servos are used for a particular function (e.g. ailerons), so that all the servos move absolutely synchronously.
PAGE 15
6. FUNCTIONS 6.1. Binding When you wish to use the Graupner HoTT 2.4 GHz receiver with a particular transmitter, the first step must always be to “bind” the unit to “its” Graupner HoTT 2.4 GHz RF module (transmitter). However, the “binding” procedure is only required once for each receiver / RF module combination. Carry out the following steps when necessary: • Switch the transmitter and receiver on.
PAGE 16
mode manually, and the model should respond normally to control commands. If this does not occur with 100% reliability, the system should not be used. Contact your local Service Department of Graupner GmbH & Co. KG. • Range-check mode is usually terminated manually when the user presses the BIND / RANGE but ton, but it terminates automatically after about ninety seconds in any case.
PAGE 17
• Standard mode (suitable for fixed-wing model aircraft only): when you press the BIND / RANGE button, the transmitter beeps four times; both LEDs are off. In this mode the throttle servo (channel 1) moves to the Fail-Safe position, i.e. the position you have programmed for a Fail-Safe situation, while all the other channels remain at “Hold”. Move the throttle stick to the desired position, then hold the BIND / RANGE button pressed in for three to four seconds.
PAGE 18
the corresponding products. See also chapter 7. 6.8. Data Storage micro-SD and micro-SDHC Any standard commercial micro-SD memory card with a capacity of up to 2 GB can be used, and also any micro-SDHC card of up to 32 GB. However, the manufacturer recommends the use of memory cards with capacities up to only 4 GB, as these are completely adequate in all normal circumstances. The memory cards for which the transmitter is intended are familiar from their use in digital cameras and mobile telephones.
PAGE 19
7. Firmware Update Graupner-HoTT Module M-G1 Firmware updates for the transmitter RF module can be transferred via the USB1-socket in conjunction with a PC running Windows XP, Vista or 7. For this you also require the USB interface, Order No. 7168.6, and the adapter lead, Order No. 7168.6A, which are available separately. The programs and files required for this are available from www.graupner.de in the Download area for the corresponding products.
PAGE 20
release the button, and the firmware update process commences. If the device is not recognised, if the pop-up window “Target device ID not found” appears, or if the process fails before 100% is reached, you must restart the update procedure. Repeat all the steps as described above. The Status display and the Progress bar show the progress of the firmware update. The update is completed when the message “Complete…100%” or “Complete!!” appears.
PAGE 21
Konformitätserklärung gemäß dem Gesetz über Funkanlagen und Telekomunikationsendeinrichtungen (FTEG) und der Richtlinie 1999/5/EG (R&TTE) Declaration of Conformity in accordiance with the Radio and Telecomunikations Terminal Equipment Act (FTEG) and Directive 1999/5/EG (R&TTE) Graupner GmbH & Co. KG Henriettenstraße 94-96 D-73230 Kirchheim/Teck declares that the product Module M-G1 HoTT - No. 33300 Module mx-16 HoTT - No. 33301 Module M-G2 HoTT - No.
PAGE 22
Environmental Protection Notes When this product comes to the end of its useful life, you must not dispose of it in the ordinary domestic waste. The correct method of disposal is to take it to your local collection point for recycling electrical and electronic equipment. The symbol shown here, which may be found on the product itself, in the operating instructions or on the packaging, indicates that this is the case. Individual markings indicate which materials can be recycled and re-used.
PAGE 23
Wir gewähren auf dieses Erzeugnis eine / This product is / Sur ce produit nous accordons une 24 Garantie von warrantied for garantie de Die Fa. Graupner GmbH & Co. KG, Henriettenstraße 94-96, 73230 Kirchheim/Teck gewährt ab dem Kaufdatum auf dieses Produkt eine Garantie von 24 Monaten. Die Garantie gilt nur für die bereits beim Kauf des Produktes vorhandenen Material- oder Funktionsmängel.
PAGE 24
Graupner GmbH & Co. KG Henriettenstraße 94 – 96 D-73230 Kirchheim/Teck Germany www.graupner.de Änderungen sowie Liefermöglichkeiten vorbehalten. Lieferung durch den Fachhandel. Bezugsquellen werden nachgewiesen. Für Druckfehler kann keine Haftung übernommen werden. Specifications and availability subject to change. Supplied through specialist model shops only. We will gladly inform you of your nearest supplier. We accept no liability for printing errors.