LAVADORA WASHING MACHINE FA825E FA1025E 35.292.
Dear customer, ENGLISH Please read these operating instructions carefully and pay particular attention to the safety notes indicated in the first pages. We recommend that you keep this instruction booklet for future reference and pass it on to any future owners. Transport damages When unpacking the appliance, check that it is not damaged. If in doubt, do not use it and contact the Service Centre.
Contents Warnings Disposal 27-28 Maintenance 28 Tips for environmental protection 28 Technical specifications Installation 29 30-31 Unpacking 30 Hydraulic connection 30 Levelling 31 Electrical connection 31 Your new washing machine 32 Description of the appliance 32 Detergent dispenser drawer Use Control panel Controls Washing hints 33 33 33-34 35 Sorting the laundry 35 Temperatures 35 Before loading the laundry 35 Maximum loads 35 Laundry weights 35 Removing stains 35 Deter
Warnings Installation • Leave the porthole door slightly ajar when the appliance is not in use. This preserves the door seal and prevents the formation of musty smells. • All internal packing must be removed before using the appliance. Serious damage may be caused to the machine or adjacent furniture if the protective transit devices are not removed or are not completely removed. Refer to the relevant paragraph in the instruction book. • Always check that water has emptied out before opening the door.
Child safety • Keep all detergents in a safe place out of children’s reach. • Children are often not aware of how dangerous electrical appliances can be. When the machine is working, children should be carefully supervised and not be allowed to play with the appliance. • Make sure that children or pets do not climb into the drum. • When the appliance is to be scrapped, cut off the electrical supply cable and destroy the plug with the remaining cable.
Intallation instructions It is dangerous to alter the specifications or attempt to modify this product in any way. Care must be taken to ensure that the appliance does not stand on the electrical supply cable. Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person. The power supply cable only can be replaced by a person of our Service Force Centre.
Installation Transit security bars Hydraulic connection Before starting the machine up, the transport security bars must be removed as follows: You are advised to keep all the transport security bars. In case the appliance has to be transported again. There should be a COLD WATER tap near the washing machine with a screwing on connection pipe of 3/4 gas for the water supply, a sink, a wash basin or a drainage system in the wall. Previously check if: 1.
IMPORTANT: The distance from the floor to the highest part of the hose should be between 60 to 90 cm. (It is advised to be between 60 and 70 cm). The hose must not be bent nor twisted to avoid clogging. Should a prolongation of the discharging hose be unavoidable this must never surpass 1.5 m and must be of the same diameter as the original hose. Make sure the hoses are not too tense. Electrical connections Before plugging the appliance make sure that: 1º.
Your new washing machine This new machine meets all modern requirements for effective treatment of laundry with low water, energy and detergent consumption. • The balance control device reduces the risk of instability in machine movement and it guarantees a quieter operation.
Use ENGLISH Control panel 1. Detergent dispenser drawer 3. DIARIO button Programme option buttons By selecting this option the washing cycle duration is reduced. We recommend its use for slightly soiled cotton and synthetic fabrics. Depending on the programme, different option buttons can be combined. When these buttons are pressed, the corresponding lights come on. When they are pressed again, the lights go off.
7. Programme progress display • NO SPIN: by selecting this option all the spinning phases are turned off. To be used for extremely delicate items. During programme development, the light corresponding to the cycle phase which the machine is in will illuminate.
Laundry weights Washing hints The following weights are indicative: Follow the wash code symbols on each garment label and the manufacturer’s washing instructions. Sort the laundry as follows: whites, coloureds, synthetics, delicates, woollens. Temperatures 90° 60° for normally soiled white cottons and linen (e.g. tea cloths, towels, tablecloths, sheets...) for normally soiled, colour fast garments (e.g. shirts, night dresses, pyjamas....
Quantity of detergent to be used Ink: depending on the type of ink, moisten the fabric first with acetone (*), then with acetic acid; treat any residual marks on white fabrics with bleach and then rinse thoroughly. The type and quantity of detergent will depend on the type of fabric, load size, degree of soiling and hardness of the water used. Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with detergent paste. (*) do not use acetone on artificial silk.
International wash code symbols Energetic wash 95 60 40 30 Max. wash temperature 95°C Max. wash temperature 60°C Max. wash temperature 40°C Max. wash temperature 30°C Delicate wash 60 Bleaching Bleach in cold water 40 ENGLISH These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.
Operating sequence Before washing your first load of laundry, we recommend that you run a cotton cycle at 60° C, with the machine empty, in order to remove any manufacturing residue from the drum and tub. Pour half of the normal amount of detergent into the main wash compartment and start up the machine. 1. Place the laundry in the drum 4. Select the required programme Open the door by pulling the handle outwards. Place the laundry in the drum, one item at a time, shaking them out as much as possible.
7. Start the machine Before starting the machine check that: Firstly, stop the machine by pressing INICIO / PAUSA button. After about one or two minutes the door can be opened. If the door does not open , this means that the temperature of the water is too high, that the water level exceed the lower limit of the door (which could cause overflowing) or that the drum is spinning. If the door cannot be opened but you need to open it, switch the machine off by turning the selector dial to “O”.
Programme table Washing programmes for cotton and linen Programme selector dial position Washing programme Description Possible option Load Prelavado o lejía Diario Super aclarado Antiarrugas (*) 4,5 kg Prelavado o lejía Super aclarado Antiarrugas (*) 4,5 kg Fast coloured cotton or linen Wash at 40° C COLORES fabrics, moderately soiled, shirts, 3 rinses ALGODÓN RESISTENTES blouses, underwear.
Programme table Washing programmes for synthetics, mixed fabrics, delicates, wool 40 SINTÉTICOS Washing programme Stains and type of fabric Description Possible option Load PLANCHADO FÁCIL Special programme for synthetic fabrics, which makes ironing easier.
Programme table Special washing programmes Programme selector dial position Washing programme Description With this programme it is possible to rinse and spin garments which have been washed by hand. The machine performs 3 rinses, and it finishes with a short spin. 3 rinses Short spin This programme can be used to perform a short spin: for garments washed by hand, for example: to wring them out, before hanging CENTRIFUGADO them up.
1. Bodywork 3. Cleaning of the drainage area Clean the outside of the machine with warm water and a neutral, non-abrasive household detergent. Rinse with clean water and dry with a soft cloth. The drainage area must be cleaned if the pump has been blocked with objects such as buttons, safety pins, coins, etc. , or if lint has built up because clothes that generate lint have been washed at high temperatures. Important: do not use methylated spirits, solvents or similar products to clean the bodywork.
4. The water inlet hose filter 6. Frost precautions If it takes longer to fill up the washing machine it is time to check the water inlet hose filter it may be clogged. If the machine is installed in a place where the temperature could drop below 0°C, proceed as follows: Turn off the water tap. • disconnect the appliance; Unscrew the fixing nut of the inlet hose. • close the water tap; Remove the filter from the electrovalve and clean it with a hard bristle brush and replace it.
Something not working? Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling technical service. Before contacting your local Service Force Centre, please check the following possible problems listed below. During machine operation it is possible that FIN light flashes to indicate that something is not working correctly. • 2 flashes = the water is not drained. • 1 flash = there is no water filling.
Problems Possible cause - Unsatisfactory washing results: • Little detergent or an inappropriate one has been used. An insufficient amount of detergent leaves the laundry looking grey. • Stubborn stains have not been treated prior to washing. • The correct wash programme has not been selected. • Too much laundry has been placed in the drum. - The machine vibrates when spinning: • The transit bolts and packaging have not been removed. • The machine is in contact with the wall or furniture.
If you are unable to identify or solve the problem, contact our service centre. Before telephoning, make a note of the model, serial number and purchase date of your machine: the Service Centre will require this information. Mod. .......... Prod. No. ........... Ser. No. ......... Mod. .......... Prod. No. ........... Water is not visible in the machine. The machine, which is the result of modern technology, runs in a very economical way with low water consumption. Performance is nevertheless excellent.
EHPOESL/Z - 09/2002
