822 90 11-01
THANK YOU for choosing your new dishwasher from us. We hope it will give you every satisfaction. Please read through these instructions carefully. You will then quickly learn how to use the machine and make the most of its features. Pull up a chair beside the machine so that you can familiarise yourself with the various controls and functions as you read the instructions. Note! Save these instructions.
Safety information Read through these instructions carefully, taking note of all directions, advice and warnings before installing the dishwasher and using it. To avoid unnecessary mistakes and accidents, it is important to ensure that all persons using the dishwasher are thoroughly familiar with its operation and safety features. Save these instructions. The dishwasher is built to wash your dishes for many years ahead and both you and any future owners can always find useful information in these pages.
General advice Damage in transit If the machine has been damaged during transportation, you should immediately notify the company responsible for delivering it. Check that the dishwasher is undamaged. If you discover any damage, faults or that anything is missing, you should notify the seller immediately. Never leave packaging material in a place where children may play with it.
Test the machine by running a cycle 1. Scrape or rinse off solid food remnants. 2. Load the dishwasher. (See page 7: "LOADING") Fill up the rinse conditioner dispenser. Put the correct amount of detergent on the inner door. 3. Close the door. 4. Select the required temperature. 5. Start the dishwasher by turning the programme knob to the start position. 6. Check the strainers to see whether they need cleaning when the dishwasher has finished the wash.
Care and cleaning 1 2 3 4 5 Rinse conditioner dispenser (1) Coarse strainer (3) Use of a rinse conditioner will result in cleaner and faster drying of the load, since it helps water and soil to run off. Too much conditioner may result in streakiness, too little may cause white spots. The dispenser holds about 140 ml. This is enough for 40-70 wash cycles, depending on the dosage setting. When the rinse conditioner level is approaching the bottom of the scale it is time to refill the dispenser.
Loading How to load the dishwasher The illustration shows the machine loaded with five place settings. Your own dishes are not likely to be identical to this load, but if you follow the advice below we are sure you will be pleased with the results. - Always place glasses, cups and bowls upside down. - Incline deep dishes (soup plates etc.) so that the water can run off when drying. - Make sure that the dishes do not rest against each other.
Controls and programme table All figures are nominal and vary for example due to temperature variations on the inlet water. The figures apply to washing up 5 IEC-settings. 1 1 3 Temperature selector 55° - Button in 65° - Button out 2 Selector knob To start the machine: - Turn the selector knob clockwise to the programme start. The ON/OFF switch is built into the programme selector. To isolate the dishwasher from the mains completely, unplug it from the wall socket.
In the event of a fault Trouble shooting list • If water leaks from the machine • Turn off the water supply tap or stopcock immediately and isolate the machine from the electrical supply by removing the plug from the wall socket. • Check that all seals, seams and connections are watertight. There is always a certain risk of leakages in any machine connected to a water supply, no matter what water safety features it may have.
Service and spare parts If you still cannot remedy the problem after following the ”Trouble shooting list”, call a repairman. Service and spare parts can be ordered from your dealer. There you will also be able to obtain advice on how to rectify the fault yourself, if possible. Before calling the dealer or a service centre, make a note of the details on the data plate affixed to the rear of the dishwasher. Make a note of the following: Brand: Date of purchase: Model: Product number: Serial number: ........
Positioning and installation Positioning In its standard version the machine is intended for installation on a kitchen sink or worktop. To function properly the machine must be fully level. Its height can be adjusted with the adjustable feet (8 mm each). Water supply The temperature of the water supply should not exceed 70°C and the pressure should be between 50-1000 kPa (0.5-10 kp/cm2). It is important to have a tap or stopcock, positioned close to the machine and with easy access.
