Model No. Product No Serial No.
Contents Page no Operating instuctions ....................................................................................... 3 Maintenance And Cleaning ............................................................................ 5 Tips on the use of the ceramic top hob unit .................................................... 8 Mounting .................................................................................................. 10 Electrical installation ...........................................
Operating instructions Switch symbols (to the left) Switch for regulating the small plate at the rear pilot light Switch for regulating the large plate at the front. Switch for regulating the double plate at the rear Switch for regulating the small plate at the front. Regulating The regulating of heat is graduation-free for all plates on a scale from 1 to 12. “1” “12” “0” Represents lowest heat Represents maximum heat. Represents “OFF”.
Pilot light Pilot light is activated as long as either of the unit's switches remains turned on. Residual-Heat indicator Each burner has a built-in indicatorlight which remains activated as long as the temperature of the burner exceeds 80 degrees Celsius, also when the burner is turned off.
Maintenance and cleaning For reasons of hygiene and safety, the cooking zones must be kept clean. Grease stains and spilled food generate smoke when heated, and can even cause fire. Panel Taking off the panel You can take the panel off, which makes it easier to clean the surface. What to do: 1. Hold the panel as shown in the diagram 2. Lift the panel straight up 3. Clean the top surface as shown under “cleaning the steel surface” 4.
Use Proper Cooking Utensils Make the most of your new ceramictop hob unit by using proper utensils of a good quality. Only pots and pans which are expressly intended for use on ceramictop hob units may be used. Utensils must, as a minimum, cover the entire circle which represents a given burner. The underside, or bottom, of the utensil must form a flat, even surface. Ensure that both contact surfaces - the utensil as well as the hob unit’s - are absolutly dry.
(use liqud AJAX or other diswashing liquid), and well wrung. All spills must be cleaned up immediately, while the burner is still warm. Use the cleaning agent supplied with the unit. Remove spots caused by utensils with aluminium bottoms, or burned grease, by polishing with the cleaning agent supplied with the unit. In extreme cases polishing may have to be repeated several times in order to remove the blemish entirely.
Tips on the use of the ceramic top hob unit Do not slide saucepans across the surface of the hob - always lift the pan when placing it on, or removing it from the ceramic surface. Wipe the bottom surface of the pots and pans with a clean dry cloth before placing them on the ceramic surface. This helps to reduce cleaning and prevents scratching the hob glass. Wipe off spills whilst the hob is warm.
The decorative pattern on the ceramic surface can become scratched and marred with use, depending upon maintenance, but does not adversely affect performance. Such blemishes are not covered by the warranty. Spills and melts must be removed immediately, while the burner is still warm, using the scraper supplied with the unit.
Mounting The hob unit can be mounted in any type of kitchen with a table surface whose thickness is between 28 mm and 40 mm. Clearance The distance between the top side of the tabletop and the carpentry underneath must be at least 45 mm. Fixing Screw the fixing brackets out to such an extent that they can be turned in under the table top. Tighten the brackets on to the table top with an ordinary screwdriver.
The unit´s externally measured length 145 mm: Cooker hood 290 mm: Two-burner standard electric hob Two-burner ceramic-top electric hob Two-burner gas hob Grill 580 mm: Four-burner ceramic-top electric hob Four-burner gas hob Installation of a single unit When mounting a single unit, be it a half-or full size unit, in a table surface which is thicker than 30 mm, it is necessary to make a special notch in both sides of the cut-out hole, as shown in the adjacent drawing.
Electrical installation The electrical connection may only be performed by a qualified electrician/ competent person. The electrical connection must be carried out in accordance with prevailing regulations for appliances using heavy current. The connection must comply with any specific requirements specified by the local electricity supply authority. There must be no interference with any of the unit’s electrical parts. The cable is mounted in the pegs as shown.
Two-phases zero-earth (max. 10A) Cable type 1 mm² HO5VV-F. The cable outside diameter must be between 7,5 and 10,5 mm. Technical data Cell Voltage 230 V Electrical connection 230/400 V 2 phases, neutral + earth Total wattage 6400W Instant heat effect 12/18 cm 1700 W Instant heat effect 21 cm 2300 W Instant heat effect 14 cm 1200 W This unit is labelled to indicate conformity with the lowvoltage directive (73/23/EEC) and the EMC directive (89/336/EEC).
16 325 88-3064 Rev.