ZRC-100 (Z-Wave Remote Controller) 1
Table of Contents Introduction .................................................... 4 Glossary .......................................................... 5 ZRC-100 Operations ....................................... 6 Product Overview ............................................. 7 Description of Function Keys .............................. 7 ZRC-100 User Interface Layout ......................... 8 Operations ..................................................... 10 Add/Delete Devices .......................
TECHNICAL SPECIFICATIONS .......................... 56 CHECKING THE ACCESSORIES ......................... 57 FCC NOTICE .................................................... 57 WARNINGS ...................................................... 57 CAUTION ........................................................
ZRC-100 (Z-Wave Remote Controller) Operating Instructions Introduction The ZRC-100 (Figure 1) is a portable Z-Wave remote controller with multi-channel support; also it is a Z-Wave Enabled Security Controller. It can control the secured door locks when it is in the security network. Also, it can be configured as a primary or secondary controller within a Z-Wave home automation network.
Glossary Device or Node Inclusion Exclusion Remove Z-Wave Network Primary Controller Secondary Controller Inclusion Controller Scene Devices and nodes are all terms to describe an individual ZWave device. These are all interchangeable when setting up your ZWave network. Add a Z-Wave device to the network. Delete a Z-Wave device from the network. To take a device out of a group, scene or association group while that device still exists in the same Z-Wave network.
ZRC-100 Operations Welcome to the world of Z-Wave home automation, you can use your ZRC-100 to control almost every Z-Wave certified products inside your house. The following section will guide you through the set up processes and operation procedures for your ZRC-100.
Product Overview Short cut keys LCD screen BACK key with backlit Navigation + OK keys with backlit Figure 2 Setup and control keys of ZRC-100 Description of Function Keys Keys Functions Short cut keys for: 1. Device and scene control 2.
ZRC-100 User Interface Layout Control menu or • Press c ord keys to select control category. • Press BACK key to go back to previous page. • Press and hold BACK key for 2 seconds to go back to root menu. Home (A1) Device (A2) Devices List (A2.1) Scene (A3) Scenes List (A3.1) Comfort (A4) Comforts List (A4.1) Sensor (A5) Sensors List (A5.
Setup menu + • Press and hold ef keys simultaneously for 3 seconds to enter Setup menu. • Press BACK key to go back to previous page. • Press and hold BACK key for 2 seconds to go back to root menu. Setup (B1) Add Device (B2) Delete Device (B3) Add to Scene (B4) Select Scene (B4.1) Remove fr. Scene (B5) (remove from scene) Select Scene (B5.1) Device Config. (B6) Device Configure (B6.1) Scene Config. (B7) Scene Configure (B7.1) Comfort Config. (B8) Comfort Configure (B8.1) Sensor Config.
Network Setup menu • Press and hold cd keys simultaneously for 3 seconds to enter Network Setup menu. • Press BACK key to go back to previous page. • Press and hold BACK key for 2 seconds to go back to root menu. + Network Setup (C1) Rediscover N.W. (C2) (Rediscover network) Re-scan Devices (C3) Delete Dead Node (C4) Listening Mode (C5) Create Sec. (C6) (Create secondary) Create Pri.
Remark: z The hard keys are valid if the backlit is turned on and vise versa. User can follow the Self Navigated Button (SNB) and LCD display for all setup procedures and operation. z User can press “ ” key to go back to the previous page or press and hold “ ” key for 2 seconds to go back to the root menu at any setup /operation screen. Add/Delete Devices Adding Device to the Network Step Setup Key LCD Indication Press and hold ef keys simultaneously for 3 seconds under the Home page.
Press the program button on the target device. Add Device Press PROG on target >>>> Saving Data … ⇓ 4 Add Device Press PROG on target >>>> OK Note 1: If you can’t add your Z-Wave device, this device might have been included in another Z-Wave network. In this case, please delete this device following the steps in the [Deleting Device from the Network] section then add this device again. Note 2: This step can be skipped if the device is already included in the network.
Setup Add Device > Delete Device > Add to Scene > OK to Enter Select “Delete Device". Setup 2 Add Device > Delete Device > Add to Scene > OK to Enter Delete Device 3 key to delete Press the device from Z-Wave network. Press the program button on the target device.
Device Control After adding devices to your ZRC-100, you can turn the device using the corresponding Device Control function. Step Setup Key LCD Indication Select “Device"and 1 key to press confirm. A corresponding Device control page will be displayed. Home Device > Scene > Comfort > OK to Enter ⇓ Devices List Switch 001 Off e Off and On f For on/off switches, press f key to turn on 2 the device and e key to turn off the device.
You can turn off all the devices in the network by selecting “All Off" function under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 4 Home Sensor > All Off OK to Enter Note 1: The screen will display LOCK /UNLK if this is a secured door lock device. Note 2: You can rename your device, please refer to user manual [step of B6 - Device Config.]. Scene Setup Scene is a collection of Z-Wave devices configured to user specified levels, settings, modes, or operating conditions.
⇓ Setup Add Device > Delete Device > Add to Scene > OK to Enter Select “Add to Scene" and press key. 2 Setup Add Device > Delete Device > Add to Scene > OK to Enter Select a Scene which you want to add the device into Scene and Select Scene Scene 1 Scene 2 3 press Scene 3 key. OK to Enter Press the program button on the target device.
Note 1: Your target device must be included in the network before this setup procedure, please refer to [Adding Device to the Network] section. Note 2: If no ACK signal received for more than 60 seconds, the “Add Device” mode will exit automatically. Removing Device/End-point from a Scene Step Setup Key LCD Indication Press and hold ef keys simultaneously for 3 seconds under the Home page.
Remove Device Press PROG on target >>>> OK Note 1: This process will only remove the target device/EP from its assigned scene but will not exclude it from the network. Note 2: If no ACK signal received for more than 60 seconds, the “Remove Device” mode will exit automatically. Scene Control After the scene setup is done, you can trigger the desired scene via scene control function on ZRC-100. Step Setup Key LCD Indication Select “Scene"and Home Device 1 key to press confirm.
Comfort Control After adding “Thermostat" or “Z-Wave to AC IR extender" to your ZRC-100, you can change the operation mode, set target temperature and fan speed via the corresponding Comfort Control function. Step Setup Key LCD Indication Select “Comfort"and key to press confirm. A corresponding Comfort Control page will be displayed.
Sensor information After adding “Binary Sensor / Multi-level Sensor"to your ZRC-100, you can monitor the sensor temperature via the corresponding Sensor function. Step Setup Key LCD Indication Select “Sensor"and Home Sensor key to press confirm. A corresponding Sensor page will be displayed. > All Off OK to Enter ⇓ 1 Sensors List Sensor 003 75 Device Configure It is allow to Move/Rename/Delete the device after added into the network under the Device Configure function.
Select “Device Configure"and press 2 Setup Remove fr. Scene key. > Device Config. > Scene Config. > OK to Enter Select your“Device" and press key. 3 Device Configure Dimmer 002 > Dimmer 004 > OK to Enter Select your action (e.g. 4 Edit Move Move) and press key. Rename Delete OK to Execute Move your selected device to your target Move position and press to save the setting.
Use cdkeys to change your character and ef keys to select character position, press save the setting. Rename Dimmer 002 to OK to Save ⇓ 7 Rename Bedroom OK to Save Select your action (e.g. 8 Edit Move Delete) and press key. Rename Delete OK to Execute 9 Press f key to confirm to delete the selected device or Press e key to cancel it and go back to previous page. Delete Dimmer 002 e NO Confirm? YES f Note 1: ZRC-100 supports up to 16 characters in a row for the device name.
Scene Configure It is allow to Move/Rename/Clear the scene after added into the scene under the Scene Configure function. Step Setup Key LCD Indication Press and hold ef keys simultaneously for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 1 Setup Add Device > Delete Device > Add to Scene > OK to Enter Select “Scene Configure"and press 2 Setup key. Remove fr. Scene > Device Config. > Scene Config.
Move your selected scene to your target Move Scene 1 Scene 2 position and press to save the setting. Scene 3 OK to Save ⇓ 5 Move Scene 2 Scene 1 Scene 3 OK to Save Select your action (e.g. Rename) and press 6 Edit Move Rename key. Clear OK to Execute Use cdkeys to change your character and ef keys to select character position, press save the setting. Rename Scene 1 to OK to Save ⇓ 7 Rename Back to Home OK to Save Select your action (e.g. Edit Move Clear) and press key.
9 Press f key to confirm to clear the selected scene or Press e key to cancel it and go back to previous page. Clear Scene 1 e NO Confirm? YES f Note 1: ZRC-100 supports up to 16 characters in a row for the scene name. Note 2: This process will only remove the scene devices/EPs from its assigned scene but will not exclude it from the network.
Select your “Thermostat"and 3 press Comfort configure key. Thermostat003 > Thermostat005 > OK to Enter Select your action (e.g. 4 Edit Move Move) and press key. Rename Delete OK to Execute Move your selected Thermostat to your target position and press Move Thermostat003 Thermostat005 to save the setting. OK to Save ⇓ 5 Move Thermostat005 Thermostat003 OK to Save Select your action (e.g. Rename) and press 6 Edit Move Rename key.
Rename Bedroom OK to Save Select your action (e.g. 8 Edit Move Delete) and press key. Rename Delete OK to Execute 9 Press f key to confirm to delete the selected thermostat or Press e key to cancel it and go back to previous page. Delete Thermostat003 e NO Confirm? YES f Note 1: ZRC-100 supports up to 16 characters in a row for the scene name. Note 2: This process will only remove the devices/EPs from its catalogue but will not exclude it from the network.
Setup Add Device > Delete Device > Add to Scene > OK to Enter Select “Shortcut key" and press key. 2 Setup Comfort Config. > Sensor Config. > Shortcut Key > OK to Enter Select your target shortcut key by ef keys (e.g. F1) then press Shortcut Key F1 F2 F3 3 key. e 4 Select your target Device / Scene / All Off for your shortcut key or Select your target shortcut page (Comfort / Sensor) for your shortcut key.
Z-Wave Advanced Setup Learning Mode (Replicating All Network and Device Information from a Primary Controller to your ZRC-100) Your ZRC-100 can: • Copy the settings from another Z-Wave controller. • Be included into existing Z-Wave network and act as a secondary remote controller or back to a new primary remote controller. • Be excluded from the Z-Wave network. Step Setup Key LCD Indication 1 Place the two controllers close to each other.
the primary controller user manual for more information) Place the two controllers close to each other. 5 (LCD display OK if the learning mode is successful. LCD display ERROR if the learning mode is unsuccessful.
Configure Association (Assign Association for Two Devices) The ZRC-100 can be used to assign one device to automatically interact directly with another device. For example you can assign a door sensor (primary node) to turn on the light switch (secondary node) when the door is opened. Adding Device/End-point to an Association Group Step Setup Key LCD Indication Press and hold ef keys simultaneously for 3 seconds under the Home page.
Assign an “Assoc. ID" (e.g. 001) by using cdkeys to change your number and ef keys to select number position. Add Assoc. Assoc. ID (1-255) 000 OK to Save 5 key to save Press the settings. ⇓ Add Assoc. Assoc. ID (1-255) 001 OK to Save Press the program/EP button on the secondary device (e.g. light switch) Add Assoc. Press PROG on Sec. >>>> e.g. light switch ⇓ 6 Add Assoc. Press PROG on Sec. >>>> e.g. light switch OK Press the program/EP button on the primary device (e.g.
Note 1: Your target device must be included in the network before this setup procedure, please refer to [Adding Device to the Network] section. Removing Device/End-point from an Association Group Step Setup Key LCD Indication Press and hold ef keys simultaneously for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 1 Setup Add Device > Delete Device > Add to Scene > OK to Enter Select “Advanced 2 Setup Setup"and press key.
Select an “Assoc. ID" (e.g. 001) by using cdkeys to change your number and ef keys to select number position. Remove Assoc. Assoc. ID (1-255) 000 OK to Save 5 key to save Press the settings. ⇓ Remove Assoc. Assoc. ID (1-255) 001 OK to Save Press the program/EP button on the secondary device (e.g. light switch) Remove Assoc. Press PROG on Sec. >>>> e.g. light switch ⇓ 6 Remove Assoc. Press PROG on Sec. >>>> e.g. light switch OK Press the program/EP button on the primary device (e.g.
Note 1: This process will only remove the target device/EP from its assigned association group but will not exclude it from the network. Deleting an Association Group Step Setup Key LCD Indication Press and hold ef keys simultaneously for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 1 Setup Add Device > Delete Device > Add to Scene > OK to Enter Select “Advanced 2 Setup Setup"and press key.
Select an “Assoc. ID" (e.g. 001) by using cdkeys to change your number and ef keys to select number position. Delete Assoc. Assoc. ID (1-255) 000 OK to Save 5 key to save Press the settings. ⇓ Delete Assoc. Assoc. ID (1-255) 001 OK to Save Press the program/EP button on the primary device (e.g. door sensor) Delete Assoc. Press PROG on Pri. >>>> e.g. door sensor ⇓ 6 Delete Assoc. Press PROG on Pri. >>>> e.g.
Change Device Configuration This function is used to modify the parameter of the Z-Wave device via the configuration command class. Look up the Parameter No. and Parameter Value of the target device from the device user manual before you start the below process. Step Setup Key LCD Indication Press and hold ef keys simultaneously for 3 seconds under the Home page.
Use cdkeys to change your parameter value and ef keys to select number position, press 5 to save the setting. Configuration Parameter Value +0000000000 OK to Save (Parameter value from 2147483648 to +2147483647 (32bits value) Press the program button on the target device.
Resetting Your Network You can reset your ZRC-100 to clear all Z-Wave network and device information by the following steps: Step Setup Key LCD Indication Press and hold ef keys simultaneously for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 1 Setup Add Device > Delete Device > Add to Scene > OK to Enter Select “Advanced 2 Setup Setup"and press key.
Reset to Default Under progress ..... Waiting ⇓ Reset to Default Successful! OK Note: After reset the remote, each device should individually perform in the section on “Delete device from the network” and “Add device to the network”. System Settings Step Setup Key LCD Indication Press and hold ef keys simultaneously for 3 seconds under the Home page.
Select “LCD Contrast "and press 3 System Settings LCD Contrast B.L. Brightness key. Sleep Timer OK to Enter Press ef keys to adjust the LCD contrast. LCD Contrast 50 % - 4 + e Control f 5 Press key to save and return to previous page then select “B.L. Brightness"and press System Settings LCD Contrast B.L. Brightness Sleep Timer OK to Enter key. 6 Press ef keys to adjust the backlight brightness. B.L.
About ZRC-100 Step Setup Key LCD Indication Press and hold ef keys simultaneously for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 1 Setup Add Device > Delete Device > Add to Scene > OK to Enter Select “About"and Setup key. It will press show the firmware version on the screen. Advanced Setup > System Settings > About > OK to Enter ⇓ 2 About Remotec Technology Host FW Ver. : 1.
Z-Wave Network Setup Rediscover Network (N.W.) During normal operation the network decides the best path to route signals from one device to another. If devices are moved to different positions in the installation, it is recommended to rediscover the network so the routing path will be re-configured. Step Setup Key LCD Indication Press and hold cb keys simultaneously for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 1 Network Setup Rediscover N.W.
Re-scan (Rediscover) Devices from network In most cases, Z-Wave gateway is the primary controller (control center), all Z-Wave devices will be added / (inclusion) by the Z-Wave gateway. Normally, it is need to click the PROG button of the Z-Wave device to add into the network and one by one. The gateway will create a control page / section to Z-Wave devices. User can control / monitor Z-Wave devices under the control page.
Press f key to confirm re-scan devices or press e key to cancel it and go back to previous page. Re-scan Devices Caution! This action will wipe out all existing device names e NO 3 The remote will re-scan all devices from network, discovered devices will be reassigned to their default categories (Devices, Comforts and Sensors) names will be reassigned in ascending order. The LCD will display OK and go back to previous page when it is completed.
Delete Dead Node from Network Step Setup Key LCD Indication Press and hold cb keys simultaneously for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 1 Network Setup Rediscover N.W. > Re-scan Devices > Delete Dead Node > OK to Enter Select “Delete Dead 2 Network Setup Node” and press key. Rediscover N.W. > Re-scan Devices > Delete Dead Node > OK to Enter The remote is checking the dead node.
Use cb keys to select the dead node device Dead Node Dimmer 002 key to then press delete it from network. OK to Delete ⇓ 4 Dead Node OK Note 1: Only the Primary Controller can be used to include or delete devices from a network. It is recommended that you mark the primary controller for each network for ease in modifying your network.
Network Setup Rediscover N.W. > Re-scan Devices > Delete Dead Node > OK to Enter Select “Listening Mode” and press key. 3 Network Setup Listening Mode > Create a Sec. > Create a Pri > OK to Enter 4 The remote is entry the listening mode. (Listening mode will automatically exit after 1 minute of inactivity.) Listening Mode Listening… >>>> Note1: The mode must not be exited during communication process with another controller.
⇓ Network Setup Rediscover N.W. > Re-scan Devices > Delete Dead Node > OK to Enter Select “Create a Sec.” then press Network Setup key. 3 Listening Mode > Create a Sec. > Create a Pri > OK to Enter 4 Please make sure the target secondary controller is setup to receive information mode. (e.g. target secondary controller should entry the “Learning mode" if this is a another ZRC100.
Step Setup Key LCD Indication 1 Place the two controllers close to each other. - Press and hold cb keys simultaneously for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 2 Network Setup Rediscover N.W. > Re-scan Devices > Delete Dead Node > OK to Enter Select “Create a Pri.” then press Network Setup key. 3 Listening Mode > Create a Sec.
WIRELESS INFORMATION Wireless range: This device has an open air line of sight transmission distance of 100 feet which complies with the Z-Wave standards. Performance can vary depending on the amount of objects in between Z-Wave devices such as walls and furniture. Every Z-Wave device set up in your house will act as a signal repeater allowing devices to talk to each other and find alternate routes in the case of a reception dead spot. Radio frequency limitations: 1. Each wall or object (i.e.
Q A What can the Remotec ZRC-100 do for me? A single Z-Wave network can include 232 nodes. If necessary, more than one network can be bridged to extend the number of nodes further, although this is normally not needed in a residential environment. The total number of controllable End-point (EP) / device / sensor is 128 items which is listed on the “Device” and “Sensor” page. ZRC-100 also supports 6 thermostats which are listed on the “Comfort” page.
Q A Can I include all Z-Wave devices from the network by ZRC100 and no need to click the PROG button for each device? Yes! ZRC-100 provides a useful function which is “Re-scan Devices” that allows rediscovering all Z-Wave devices from the network. Please refer to user manual with below steps: i) Assume all Z-Wave devices have been added by gateway. ii) ZRC-100 should act as a secondary controller [step of B11.1]. iii) Execute the “Re-scan Devices” function [step of C3].
z Z-Wave power strip Multi-Channel Device End Point 1 Multi-Channel Device End Point 4 Please refer to the target device user manual for more information such as Inclusion / Exclusion and add End Point to a Scene / Group. Some multi-channel device in the market may lack of the capability to report Multi-Channel Capability Report (MCCR) for each end point (channel).
Q A Q A Q A Where can I keep up to date with the latest Z-Wave products for my house? You can keep up to date by visiting the www.remotec.com.hk website where we will have information and ideas for using ZWave technology. How do I know which product is compatible to my ZRC-100 remote? You can check either the specifications in the manual of your remote or also check online at www.remotec.com.hk for a full list of products that can be used with your remote.
TECHNICAL SPECIFICATIONS Model No. BW8380US (ZRC-100US) Model No. BW8380EU (ZRC-100EU) Model No. BW8380AU (ZRC-100AU) Model No. BW8380IN (ZRC-100IN) RF Frequency 908.4MHz (US) RF Frequency 868.4MHz (EU) RF Frequency 921.4MHz (AU) RF Frequency 865.2MHz (IN) LCD FSTN Positive Transflective 128x64 dots at A.A.= 35.8x21.7mm LCD and key pad backlight color Amber Max.
COMMAND_CLASS_THERMOSTAT_FAN_MODE YES NO COMMAND_CLASS_SENSOR_BINARY YES NO COMMAND_CLASS_SENSOR_MULTILEVEL YES NO COMMAND_CLASS_CONTROLLER_REPLICATION NO YES COMMAND_CLASS_ASSOCIATION YES YES COMMAND_CLASS_MULTI_CHANNEL YES NO COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION YES YES COMMAND_CLASS_VERSION NO YES COMMAND_CLASS_CONFIGURATION YES NO COMMAND_CLASS_MANUFACTURER_SPECIFIC NO YES COMMAND_CLASS_WAKE_UP NO YES COMMAND_CLASS_DOOR_LOCK YES NO COMMAND_CLASS_SECURITY YES YES
Exercise extreme caution when using Z-Wave devices to control appliances. Operation of the Z-Wave device may be in a different room then the controlled appliances, also an unintentional activation may occur if the wrong button on the remote is pressed. Z-Wave devices may automatically be powered on due to timed event programming. Depending upon the appliance, these unattended or unintentional operations could possible result in a hazardous condition.