Wireless remote control 10-channel ZW fb GB User manual for art. no. 054450 WIRELESS SYSTEM Z-WAVE Harkortstr. 2 • 58339 Breckerfeld • Germany • www.duewi.
Wireless remote control 10-channel ZW fb GB TECHNICAL DATA ZW FB 10 XXX EVFXJ EF ;8 '# 'VOL 'FSOCFEJFOVOH #BUUFSJF Y 7 """ 'SFRVFO[ .)[ #FUSJFCTUFNQFSBUVS $ $ *ODM I Include &YDM E Exclude "TTPD -PX #BUU Low Battery (status ind. for battery) A Associate •Transmitting frequency: •Battery: •Number of channels: •Operating temperature: •Range: 868.42 MHz 4x 1.
Wireless remote control 10-channel ZW fb GB Function buttons on the düwi controller EÔXJ SFNPUF DPOUSPM BSU OP EÔXJ XJSFMFTT XBMM USBOTNJUUFS BSU OP EÔXJ XJSFMFTT TXJUDIJOH DFOUSF BSU OP Å VQ 4 4UBUVT Å *ODMVEF &YDMVEF " "TTPDJBUF * Ç VQ & EPXO * *ODMVEF & &YDMVEF " "TTPDJBUF Ç EPXO "MM 0O "MM 0ñ 0O 0ì " "TTPDJBUF & &YDMVEF * *ODMVEF Function buttons on the düwi receiver düwi wireless flush mounted switch, art. no.
Wireless remote control 10-channel ZW fb GB TECHNICAL drawings 1.5 70.9 10.6 4 3 45 80 + -0 0.2 .2 6 70.9 R2 +0.1 60 -0.1 12.9 Harkortstr. 2 • 58339 Breckerfeld • Germany • www.duewi.
GB Contents Page 1.0 The Z-Wave® wireless system ���������������������������������������������������������������������������������������������������������������������������������������6 1.1 Information on the Z-Wave wireless system ��������������������������������������������������������������������������������������������������������������������� 6 1.
GB 1.0 The Z-Wave® radio system 1.1 Information on the Z-Wave radio system Z-Wave® • Is an internationally established and defined standard for the control of wireless systems • Is a professional, reliable and easy to operate wireless system on the interference-free frequency of 868.
GB 2.2 General safety instructions Only authorised, suitably qualified personnel are allowed to work on 230 V mains taking into account national installation regulations/standards. Prior to installing the product, the mains supply is to be isolated and secured against unintentional switch on. In the case of battery-operated devices, attention is to be paid to the correct polarity of the batteries on insertion. • The product is only allowed to be used as intended (as described in the user manual).
GB 3.1 LED Indications 3.1.1 Overview of LED indications on the devices You will find an overview of the various LED indications on page 2. 3.1.2 Advantages of the LED indications As a result of the colour LED indication on the transmitters and receivers it is at all times possible • To obtain feedback on the success/failure of switching commands or configuration steps. • To enquire about the status of devices (on/off/up/down/battery).
GB Both controller and target device indicate successful inclusion for 3 seconds with a green LED indication, failed inclusion with a red LED indication. The device is now allocated directly to the required group. Repeat the procedure to include additional devices. In general you can allocate a device to one or more different groups (e.g. a standard lamp can be switched in group "1" with the dining room lighting and in group "2" with the living room lighting). 3.2.
GB Both controller and target device indicate successful removal for 3 seconds with a green LED indication, failed removal with a red LED indication. After successful removal, the device is in the delivery state again. 3.3.2 Removing an additional controller from the network (e.g.
GB 3.3.4 Deleting wireless switching centre/server as primary controller and network If you have a wireless switching centre/server as the primary controller in the network, the network data are deleted as follows: LED Controller 10 sec. I + E + A flashes red/yellow/ green • Press simultaneously for 10 seconds the "Include" I + "Exclude" E + " Associate" A buttons on the controller. A successful reset is indicated by red/yellow/green flashing of the status LED. 3.
GB 3.4.2 Activation of the All On/All Off functionality To be able switch devices from different groups or scenes simultaneously (e.g. switching off all appliances on leaving the housing or switching on all lights in case of danger), these devices can be specifically allocated to the All On/Off group on the remote control or a wall transmitter. Remote control 2 sec.
GB In the case of the "Sequence" type of protection, the device can be unlocked briefly by pressing 3x the function buttons ( 1 / 2 ), the LED indication illuminates green if successful. 5 seconds after the last button press the device is protected again automatically, the LED indication flashes red during this process. 3.5 Working with more than one controller 3.5.
GB Both controller and target device indicate successful inclusion for 3 seconds with a green LED indication, failed inclusion with a red LED indication. 3.5.4 Allocating an already included device to any group/scene (If the device is to be allocated to a scene with a defined nominal state, e.g. with a specific brightness, set to device to this state by pressing the related function button ( 1 / 2 ).
GB 3.5.6 C onnecting flush mounted modules or plug adaptors with a wall transmitter (if there is no direct wireless connection) If you want to connect a wall transmitter with a flush mounted module in the network that cannot be reached directly from a wall transmitter already installed, proceed as follows Controller 2 sec. A 1x I Receiver Controller 2 3x 1 / 2 3x Å / Ç • Press for 2 seconds the "Associate" A button on the controller. • Briefly press the "Include" I button on the controller.
GB 3.6.2 Deleting a complete group/scene – devices remain in the network (Disassociation) Controller LED 10 sec. A flashes blinkt red/yellow/ rot/gelb/ green grün Controller 1x LED Ç illuminates leuchtet grün green • Press the "Associate" A button on the related controller for 10 seconds (remote control/wall transmitter). • The LED starts to flash red/yellow/green. • Press the "DOWN" Ç button on the controller for the related group/scene.
GB 3.7.1 Inclusion of a wireless switching centre/server in an existing network First include the wireless switching centre/server in the current primary controller: Controller 3x LED I Switching server 2 sec. I flashes blinkt grün green LED illuminates green • Press 3x the "Include" I button on the primary controller. • The LED starts to flash green and permits the inclusion of the wireless switching centre/server for 15 seconds.
GB 4.0 Annex 4.1 WARRANTY Claims under the warranty are subject to statutory provisions. Subject to technical change without notice. • Our products are manufactured using the latest technology and are subject to strict quality control. Should, nevertheless, defects occur on your device, düwi GmbH provides a warranty as detailed below.