Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES
YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS
REMOVED OR THE CIRCUIT BREAKER IS SHUT OF.
GENERAL You don’t need special tools to install this fixture. Be
sure to follow the steps in the order given. Under no
circumstances should a fixture be hung on house electrical wires,
nor should a swag type fixture be installed on a ceiling which
contains a radiant type heating system. Read instructions
carefully. If you are unclear as to how to proceed, consult a
qualified electrician. NOTE: Proper wiring is essential for the safe
operation of this fixture.
GENERAL
You don’t need special tools to install this fixture. Be sure to
follow the steps in the order given. Under no circumstances
should a fixture be hung on house electrical wires, nor should a
swag type fixture be installed on a ceiling, which contains a
radiant type heating system. Read instructions carefully. If you
are unclear as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this
fixture.
FIXTURE ASSEMBLY
Carefully removed the fixture from the carton and check that all
parts are included as shown in figure. Be careful not to misplace
any of the screws or parts, which are needed to install this fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP1: Install universal mounting plate (B) on the outlet box,
make sure the two ribs (E) on the mounting plate (B) must be in
the vertical position.
Proceed to connect wires:
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two
raised dimples on the circular strap. Wrap the ground wire from
the fixture (if supplied) around the green grounding screw, then
connect it to ground wire from the outlet box (if not fixed on the
outlet box) using a wire connector (not supplied). If ground wire
from the fixture is not supplied, wrap the ground wire (if not fixed
on the outlet box) from the outlet box around the green grounding
screw and tighten it. NEVER CONNECT GROUND WIRE TO
BLACK OR WHITE POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and connect the
wires according to the directions below:
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer
wire is square shaped or ridged and the less tracer wire is round
in shape or smooth (seen best when viewed from wire end.)
STEP 2: Take your fixture wire(s) from group A and
place evenly against the black wire from the outlet box.
Do NOT twist wires together before using wire
connectors.
STEP 3: Fit a wire connector (not supplied) over the wires and
screw the connector clockwise until you feel a firmness..
STEP 4: Try gently to pull the connector off the wires. If you can
pull the connector off, carefully re-do steps 3 and 4, as
above, and check again for a firm connection.
STEP 5: Connect the fixture wire from group B to the white wire
from the outlet box in the same manner.
GROUP A: Connect to
Black
House Wire
GROUP B: Connect to
White
House Wire
BLACK
WHITE
*PARALLEL WIRE (round
& smooth)
smooth)
*PARALLEL WIRE (square
& ridged)
ridged)
WHITE OR GREY
WITH TRACER
WHITE OR GREY
WITHOUT TRACER
BROWN GOLD OR
BLACK WITHOUT TRACER
BROWN, GOLD OR
BLACK WITH TRACER
FINIAL ASSEMBLY
STEP1: After wires are connected, tuck them carefully
inside outlet box.
STEP2: Put the back plate (D) over the universal
mounting plate (B) and secure it to universal mounting
plate rib (E) with mounting screw (C).
STEP3: Install bulb (I) to socket (H) (Do not exceed the
maximum capacity recommended on the socket.)
STEP4: Thread metal shade (J) to fitter (G) tightly
STEP5: The arm (F) could be spin to the angle desired.
(Note: Max. 350∘.(See Fig. 2)
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass
with a mild soap. Do not use abrasive materials such
as scouring pads or powders, steel wool or abrasive
paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you
need to order replacement parts. All parts for this
fixture can be ordered from place of purchase. Be sure
to use exact wording from illustration when ordering
parts.
Line art shown may not exactly match the fixture
enclosed. However, the installations do apply to
this fixture.
ITEM NO: 814-2S-MB
`