Installation Sheet

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING
ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS
SHUT OFF. GENERAL You don’t need special tools to install this fixture. Be
sure to follow the steps in the order given. Under no circumstances should a
fixture be hung on house electrical wires, nor should a swag type fixture be
installed on a ceiling which contains a radiant type heating system. Read
instructions carefully. If you are unclear as to how to proceed, consult a
qualified electrician. NOTE: Proper wiring is essential for the safe operation
of this fixture.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be
hung on house electrical wires, nor should a swag type fixture be
installed on a ceiling, which contains a radiant type heating system.
Read instructions carefully. If you are unclear as to how to proceed,
consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
FIXTURE ASSEMBLY
Carefully removed the fixture from the carton and check that all
parts are included as shown in figure. Be careful not to misplace
any of the screws or parts, which are needed to install this
fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP1:install universal mounting plate(B) on the outlet box.
STEP2:Secure universal mounting plate(B) and outlet box with box
screw(A).
Proceed to connect wires:
GROUNDING INSTRUCTIONSSTEP 1: Insert the green grounding screw
into the hole with two raised dimples on the circular strap. Wrap the
ground wire from the fixture (if supplied) around the green grounding
screw, then connect it to ground wire from the outlet box (if not fixed on
the outlet box) using a wire connector (not supplied). If ground wire from
the fixture is not supplied, wrap the ground wire (if not fixed on the outlet
box) from the outlet box around the green grounding screw and tighten
it.NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and connect
the wires according to the directions below:
FINAL ASSEMBLY
STEP1: After wires are connected, tuck them carefully inside
outlet box.
STEP2: Put the back plate (F) on the mounting screw (D) and
secure them with the ball finial (E).
STEP3: Put the glass shade (H) and washer (I) on the socket (G),
lock the socket ring (J) on them.
STEP4: Install the G9 led bulb (K) on the socket (G) OR Install
the G9 bulb (L) ( not included ) and lock the lamp shield (M) on
the socket (G).
(CAUTION - TO REDUCE THE RISK OF FIRE, USE G9 LED
bulb or USE MAX 75 WATTS G9 Halogen bulb. DO NOT USE
TYPE G9 HALOGEN BULB WITHOUT SHIELD, DO NOT USE
SHIELD WITH TYPE G9 LED BULB. DISCONNECT POWER
BEFORE SERVICING.)
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to
order replacement parts. All parts for this fixture can be ordered
from place of purchase. Be sure to use exact wording from
illustration when ordering parts.
Line art shown may not exactly match the fixture enclosed.
However, the installations do apply to this fixture.
ITEM NO: 3010-2V,3011-2V,3012-2V,
3010-3V,3011-3V,3012-3V,
3010-4V,3011-4V,3012-4V,
3010-5V,3011-5V,3012-5V.
*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer
wire is square shaped or ridged and the less tracer wire is round
in shape or smooth (seen best when viewed from wire end.)
STEP 3: Take your fixture wire(s) from group A and place
evenly against the black wire from the outlet box. Do
NOT twist wires together before using wire connectors.
STEP 4: Fit a wire connector (not supplied) over the wires and
screw the connector clockwise until you feel a firmness.
STEP 5: Try gently to pull the connector off the wires. If you can
pull the connector off, carefully re-do steps 3 and 4, as
above, and check again for a firm connection.
STEP 6: Connect the fixture wire from group B to the white wire
from the outlet box in the same manner.
GROUP A: Connect to Black
House Wire
GROUP B: Connect to White
House Wire
BLACK
WHITE
*PARALLEL WIRE (round &
smooth)
*PARALLEL WIRE (square &
ridged)
WHITE OR GREY WITH
TRACER
WHITE OR GREY WITHOUT
TRACER
BROWN GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER