Brochure

ManualsBrandsZ-Flex ManualsGas Fittings & Connectors3 in. Slant/Fin Victory Concept VSPH Adapter

Table Of Contents

Z-VENT Commercial

Z-VENT IV Systems

Z-VENT IV

Features gasketed connections

No sealant required—no cure time, no call backs

The highest pressure rating in the industry

More than 5 times the industry standard and 2.5 times

higher than our competitors.

Fusion welded pipe seams

Provides an air-tight seam, smooth finish and a

better fit.

The only metallic special gas vent that can be cut to

length on site (single wall only)

Being able to cut the product in the field will save you

time and money.

Pipe available from 3” to 24”.

Z-VENT IV is a revolutionary self sealing Special Gas

Vent System that dramatically reduces the total installed

vent system cost.

Z-VENT IV components are supplied with self sealing

gasket connections that install in half the time of field

sealed systems.

Air and water tight connections ensure optimum vent

performance and reliability.

Z-VENT model SVE IV Special Gas Vent System

is tested and listed by Underwriters Laboratories to UL

1738 Venting Systems for Gas-Burning Appliances,

Category II,III and IV.

Patented Sealing System

Z-VENT IV components are supplied with factory

installed, patented, fail safe sealing gaskets.

The gaskets special design along with precision

engineered close tolerance construction components

ensure an air and water tight fit.

Leakage tested to 2 1/2 times the UL pressure

rating of 8” W.C.

Suggested Specification:

Venting shall be Z-Vent model SVE IV as manufactured by

Z-Flex. The vent system shall consist of factory welded pipe

and fittings incorporating a factory fitted sealing gasket

which, when installed in accordance with the manufacturers

installation instructions, will seal the pipe joints without

the use of field applied sealant.

The vent system shall be leakage tested to 8” W.C. positive

pressure. The vent system will be tested and listed by

Underwriters Laboratories to UL1738/ULC S636 with a

maximum allowable continuous flue gas temperature of

550°F

Sold by Cinnabar Equipment Co. 972-422-4441

Summary of content (33 pages)

PAGE 1
Z-VENT Commercial Z-VENT IV Sold by Cinnabar Equipment Co. Systems 972-422-4441 Z-VENT IV Features gasketed connections No sealant required—no cure time, no call backs The highest pressure rating in the industry More than 5 times the industry standard and 2.5 times higher than our competitors. Fusion welded pipe seams Provides an air-tight seam, smooth finish and a better fit.
PAGE 2
Z-VENT MODEL SVE IV SPECIAL GAS VENT SYSTEM Technical Data Sheet APPLICATION Z-VENT is a factory built, engineered AL 29-4C special gas venting system suitable for venting positive or negative pressure residential and commercial gas fired heating equipment. The maximum allowable continuous flue gas temperature for Model SVE IV is 550° F(288°C ). Model SVE IV Single Wall, 3 to 24in. dia.
PAGE 3
Z-Vent Single Wall AL29-4C Special Gas Vent Technical and Dimensional Data
PAGE 4
Z-Vent Single Wall AL29-4C Special Gas Vent Contents Drain Pipe Vertical in-line Drain Tee Horizontal Drain Tee Vertical Page No 15 13 13 Elbows 45 deg. Elbows 90 Deg.
PAGE 5
Z-Vent Single Wall AL29-4C Special Gas Vent Pipe Available in diameters 3in to 24in and standard lengths up to 10ft (3in and 4in diameter only). Pipe can be cut to length. The female end of each Z-Vent component incorporates a silicone sealing gasket. Examine all components to ensure that gasket integrity has remained during shipping. Gaskets must be in proper position or flue gases could leak resulting in carbon monoxide poisoning.
PAGE 6
Z-Vent Single Wall AL29-4C Special Gas Vent Tees Tee Cap with Drain A tee is used to connect horizontal and vertical vent sections A B C Part Number Description 5 10.5 6.5 2SVST05 Z-Vent Tee 5in 6 10.5 6.5 2SVST06 Z-Vent Tee 6in 7 12.5 7.5 2SVST07 Z-Vent Tee 7in 8 14.5 8.5 2SVST08 Z-Vent Tee 8in 10 18.5 10.5 2SVST10 Z-Vent Tee 10in 12 20.5 10.5 2SVST12 Z-Vent Tee 12in 14 22.5 12.5 2SVST14 Z-Vent Tee 14in 16 24.5 13.5 2SVST16 Z-Vent Tee 16in 18 26.5 14.
PAGE 7
Z-Vent Single Wall AL29-4C Special Gas Vent 45° Elbows 90° Elbows 45° elbows are used when a direction change or offset is required. A B C Part Number Description 3 3.5 2.25 2SVEEWCF0345 Z-Vent Elbow 45° x 3in 4 4 2.50 2SVEEWCF0445 Z-Vent Elbow 45° x 4in 5 4.5 2.50 2SVEEWC0545 Z-Vent Elbow 45° x 5in 6 4.75 2.75 2SVEE0645 Z-Vent Elbow 45° x 6in 7 5 4 2SVEE0745 Z-Vent Elbow 45° x 7in 8 5.
PAGE 8
Z-Vent Single Wall AL29-4C Special Gas Vent Low Resistance Rain Cap Rain Cap A low resistance rain cap is designed to terminate a vertical stack and prevent the entrance of debris or rain into the vent. It also provides low resistance to flue gas flow. A B C Part Number Description 5 5 10 2SVSRC05 Low Resistance Rain Cap 5in 6 5.5 11 2SVSRC06 Low Resistance Rain Cap 6in 7 6.5 13 2SVSRC07 Low Resistance Rain Cap 7in 8 7.
PAGE 9
Z-Vent Single Wall AL29-4C Special Gas Vent Lateral 45° Wall Termination A lateral 45° is designed to allow a low flow resistance connection of horizontal and vertical sections. A tee cap is available separately. A B C Part Number Description 5 13 12 2SVSL0545 Z-Vent Lateral 45° x 5in Tee 6 14 13 2SVSL0645 Z-Vent Lateral 45° x 6in Tee 7 15.5 14.5 2SVSL0745 Z-Vent Lateral 45° x 7in Tee 8 17 15 2SVSL0845 Z-Vent Lateral 45° x 8in Tee 10 20 17.
PAGE 10
Z-Vent Single Wall AL29-4C Special Gas Vent Increaser Reducer Adjustable 18in Used to upsize a vent system A B C Part Number Description 3 4,5,6 10 2SVSI0(A)0(B) Z-Vent Increaser(A)to(B) 4 5,6,7 10 2SVSI0(A)0(B) Z-Vent Increaser(A)to(B) 5 6,7,8 10 2SVSI0(A)0(B) Z-Vent Increaser(A)to(B) 6 7,8,10 10 2SVSI0(A)0(B) Z-Vent Increaser(A)to(B) 7 8,10,12 10 2SVSI0(A)0(B) Z-Vent Increaser(A)to(B) 8 10,12 10 2SVSI0(A)0(B) Z-Vent Increaser(A)to(B) 10 12 10 2SVSI0(A)0(B) Z-Vent
PAGE 11
Z-Vent Single Wall AL29-4C Special Gas Vent Flashing Flat Flashing 0-30° Flat flashing provides weather protection where the vent penetrates the roof or chimney. Use on flat or slightly sloped (5° slope maximum) roofs.
PAGE 12
Z-Vent Single Wall AL29-4C Special Gas Vent Wall Thimble Storm Collar For use when the vent passes through a horizontal opening. Not required for non-combustible walls.
PAGE 13
Z-Vent Single Wall AL29-4C Special Gas Vent Guy Band Firestop Support A guy band is used to stabilize the vent above the roof line or where a vent support can not be used. Secure with 4 guy wires ( not included).
PAGE 14
Z-Vent Single Wall AL29-4C Special Gas Vent Horizontal Drain Vertical Drain Tee Extended Wall Thimble Termination Tee A horizontal drain pipe is used to drain condensate from the vent system. The drain should be positioned as close as possible to the appliance and vent sloped towards it. A B C Part Number Description 3 9 2 2SVEDWC03 Z-Vent Horizontal Drainpipe 3” 4 9 2 2SVEDWC04 Z-Vent Horizontal Drainpipe 4” A vertical drain pipe is used to drain condensate from the vent system.
PAGE 15
Z-Vent Single Wall AL29-4C Special Gas Vent Termination Elbow Termination Hood* Used to terminate a horizontal vent A B Part Number Description 3 2 2SVSTEX0345 Z-Vent Termination Elbow 3 x 45 3 2 2SVSTEX0390 Z-Vent Termination Elbow 3 x 90 4 2 2SVSTEX0445 Z-Vent Termination Elbow 4 x 45 4 2 2SVSTEX0490 Z-Vent Termination Elbow 4 x 90 Used to terminate a horizontal vent section A B C Part Number Description 3 5.75 2 2SVSHTX03 Z-Vent Termination Hood 3in 4 5.
PAGE 16
Z-Vent Single Wall AL29-4C Special Gas Vent Steep Roof Flashing Vertical Drain Pipe Adapter 6in (Double Female) Used where a vertical vent section passes through the roof. Accommodates roof pitches from 40° to 90° - 8/12-12/12. Storm collar sold separately. A B C Part Number Description 3.25 16 16 2SVSADJS03 Steep Roof Flashing 3in 4.25 16 16 2SVSADJS04 Steep Roof Flashing 4in Used on vertical runs to drain condensate from the system.
PAGE 17
Z-Vent Single Wall AL29-4C Special Gas Vent Weil-Mclain Adaptor A B C Part Number Description 3 4.25 3.25 2SVEMGVX03 Weil-Mclain GV Starter 3in (Series 2) Weil-Mclain CGI Adaptor Weil-Mclain Starter Tee Series 3/4 Adaptor Safety Vent Adaptor A B Part Number Description 3 3 2SVEWMFAF03 Weil-Mclain CGI Adaptor 3in A B C Part Number Description 3 5.5 7 2SVEVSTF03 Weil-Mclain Starter Tee 3in (Series 3 & 4) A B C Part Number Description 3 5.5 3.
PAGE 18
Z-Vent Single Wall AL29-4C Special Gas Vent Buderus Adaptor A B Part Number Description 3 4.25 2SVB03 Z-Vent Buderus GA 124 244 4 4.25 2SVB04 Z-Vent Buderus GA 124 244 Burnham, Triangle Tube Adaptor Ametek Fan Adaptor Locking Bands A B Part Number Description 3 4 2SVSTA03 Burnham PV2/ Triangle Tube Adaptor A B Part Number Description 3 4.
PAGE 19
Z-Vent Single Wall AL29-4C Special Gas Vent Modine Adaptor A B Part Number Description 4 4 2SVMPE04 Z-Vent Modine PDP 125 Adaptor 4in Slant Fin Victory, Concept, VSPH Adaptor Stant Fin Termination Adaptor Smith/Hydrotherm Adaptor A B C 3 5.5 4 Part Number Description 2SVSSLA2 Slantfin Victory, Concept, VSPH Adaptor A B C Part Number Description 3 6 1.
PAGE 20
Z-Vent Single Wall AL29-4C Special Gas Vent Sta-Rite Adaptor Utica Adaptor Viessmann Vitoden Adaptor Viessmann Vitogas Adaptor A B Part Number Description 4 8.25 4STPHA04 Sta-Rite Connector A B Part Number Description 3 3.75 2SVSUBAF03 Utica Boiler Adaptor 3in 4 3.
PAGE 21
Z-Vent Single Wall AL29-4C Special Gas Vent Bosch Adaptor A B Part Number Description 4 4 2SVFX04 Bosch 125 FX Adaptor 4in Noritz Adaptor A B Part Number Description 4 6 2SVWA03 Z-Vent Adaptor Noritz 3in 4 6 2SVWA04 Z-Vent Adaptor Noritz 4in 4 6 2SVWA05 Z-Vent Adaptor Noritz 5in Adaptor Aerco A B C Part Number Description 8 13.5 11.75 2SVAER0890 Adaptor Aerco 8 X 90 Canada: 452 Attwell Drive, Etobicoke, ON M9W 5C3 tel: 416.679.0045 • fax: 416.679.0051 U.S.
PAGE 22
PAGE 23
PAGE 24
PAGE 25
PAGE 26
Z-VENT Commercial/Industrial MODEL SVE SERIES IV INSTALLATION AND MAINTENANCE INSTRUCTIONS 3”- 12” SINGLE AND DOUBLE WALL SPECIAL STAINLESS STEEL VENTING SYSTEM FOR GAS BURNING APPLIANCES CATEGORY II, III, & IV TESTED AND LISTED BY UNDERWRITERS LABORATORIES INC. UL 1738 & BH636 Note the following before installation of Z-Vent ‫ ٭‬Examine all components for possible shipping damage prior to installation. ‫٭‬ ‫ ٭‬The Z-Vent system must be free to expand and contract. Pipe must be properly supported.
PAGE 27
SPECIAL STAINLESS STEEL VENTING For use with Category I, II, III, & IV gas burning appliances Contact Local Building or Fire Officials about Restrictions and Installation Inspections in your area as well as National codes: USA National Fuel Gas Code ANSI-Z223.1/NFPA 54, CANADA -CAN\CGA-B149.1 or .
PAGE 28
JOINT PROCEDURE (see illustration #1) The female end of each Z-Vent Model SVE IV component incorporates a silicone sealing gasket. Examine all components to insure that gasket integrity has remained during shipping. 1. Align pipes and push them together as far as they will go for single wall or until lock engages for double wall. NOTE: Some flue collars may require the use of high temperature silicone sealant to make a positive pressure gas tight seal.
PAGE 29
SIDE WALL VENTING INSTALLATION (see illustration #2 below) 1. The pipe may be mortared in directly without using a wall thimble, if the wall is non-combustible. Penetrating a combustible wall requires the use of a wall thimble. Install wall thimble into wall, observing the aforementioned rules and/or local building codes. Select the point of wall penetration where the minimum 1/4 “ per foot of slope (6.4 mm per 305 mm) can be maintained. A framed opening is required to insert the thimble halves.
PAGE 30
VERTICAL VENTING (see illustrations #3 & 4) NOTE: The vent termination above the roof line shall consist of a continuous section of vent pipe only (without any joints) and must be at least 3 ft. (1 m) to a maximum of 6ft. above the roof line and 2 ft. (.61 m) higher than any part of a structure within 10 ft. (3.1 m).
PAGE 31
EXISTING MASONRY CHIMNEY (see illustration #5) NOTE: A masonry chimney flue may be used to route Z-VENT if no other appliance vents directly into the same flue without a liner. Prior to beginning the installation, be sure that the existing chimney meets all national and local building codes. The chimney must be cleaned, removing all soot, debris and creosote before installing Z-VENT. 1.
PAGE 32
APPLIANCE CONNECTION Refer to the appliance manufacturer's installation manual for proper method of joining Z-VENT to the appliance collar. An appliance adapter to suit specific requirements may be obtained from Z-FLEX. IMPORTANT NOTICE When any of the previous installation procedures are completed, be sure to go over the entire system to make sure all joints are secure and sealed correctly. The seams and joints must be checked for tightness prior to using the venting system.
PAGE 33
Z-FLEX® (“Seller”) extends the following LIMITED WARRANTY for Z-VENT (the “Z-Vent”): Seller warrants that at the time of purchase, the Z-Vent will be free of manufacturer’s defects in material and/or workmanship. This warranty shall extend to the original purchaser of the Z-Vent or, if purchased by a contractor, to the end user. This warranty is valid for a period of fifteen (15) years from the date of purchase, provided that the Z-Vent has been installed according to Z-Flex® installation instructions.