User's Manual

ManualsBrandsZ Com ManualsComputers & Accessories802.11b/g Wireless MiniPCI Card

FCC Statement

Warning: Changes or modifications to this unit not expressly approved by the

party responsible for compliance could void the user authority to operate the

equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate this equipment.

IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11.

CAUTION:

To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm

must be maintained between the antenna of this device and all persons.

This Transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter

This device is intended only for OEM integrators under the following conditions:

The antenna must be installed such that 20 cm is maintained between the antenna and users. For

laptop installations, the antenna must be installed to ensure that the proper spacing is maintained

in the event the users places the device in their lap during use (i.e. positioning of antennas must be

placed in the upper portion of the LCD panel only to ensure 20 cm will be maintained if the user

places the device in their lap for use) and The transmitter module may not be co-located with any

other transmitter or antenna. As long as the 2 conditions above are met, further transmitter testing

will not be required.

However, the OEM integrator is still responsible for testing their end-product for any

additional compliance requirements required with this module installed (for example,

digital device emissions, PC peripheral requirements, etc.).

Summary of content (6 pages)

PAGE 1
FCC Statement Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 2
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
PAGE 3
1. Introduction 802.11b/g Wireless MiniPCI Card is the perfect solution for your wireless network applications based on the IEEE 802.11g standard offering a data rate of 54Mbps in a wireless LAN environment. XG-624 is designed for Access Point, Router, ATUR, Printer Server series, IP Camera series and Internet Video Server gives you wireless access the web and network resource without the wire.
PAGE 4
3. Specification This section defines the hardware and software features, which will be required for Z-Com XG-624. 3.1 Hardware Specification Feature Lead Free Chip Solution Host Interface Connector Antenna EEPROM Power Supply Additional Information RoHs compliant AR2417 Single-Chip 32-bit MiniPCI Two U.FL-R-SMT connectors (Hirose) External Antenna 16Kbit Supply voltage +3.
PAGE 5
3.3 Wireless RF Specification Standard Data Rate Transmission/Emission Type RF Frequency Range Data modulation type Output Power Sensitivity IEEE 802.11g standard IEEE 802.11b standard 11g: 54M/48M/36M/24M/18M/12M/9/6Mbps 11b: 11Mbps/5.5Mbps/2Mbps/1Mbps Direct Sequence Spread Spectrum (DSSS) USA (FCC): 2.412GHz ~ 2.462GHz (Ch1-11) Europe (CE): 2.412GHz ~ 2.472GHz (Ch1-13) Japan (TELEC): 2.412GHz ~ 2.
PAGE 6
4. Hardware Installation The following sections in this chapter describe how to install XG-624 Module 4.1. Installation Overview XG-624 wireless module is design for Access Point, Router, ATU-R, Printer Server series, IP Camera series and Internet Video Server only. 4.2. Safety Recommendations The safety guidelines are as follows: λ Keep the board area clear and dust-free before, during, and after installation. λ Keep tools away from walk areas where you and others could fall over them.