User's Manual

ManualsBrandsZ Com ManualsComputers & AccessoriesIEEE 802.11 a/b/g/n Wireless mini-pci card

FCC Statement

Warning: Changes or modifications to this unit not expressly approved by the

party responsible for compliance could void the user authority to operate the

equipment.

The device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

The user’s manual or instruction manual for anintent ional or unintentional ra diator shall caution

the user that changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a reside ntial installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from thatto which the receiver is

needed. Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm

must be maintained between the antenna of this device and all persons.

This Transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter

This device is intended only for OEM integrators under the following conditions:

The antenna must be installed such that 20 cm is maintained between the antenna and users. For

laptop installations, the antenna must be installed to ensure that the proper spacing is maintained

in the event the users places the device in their lap during use (i.e. positioning of antennas must be

placed in the upper portion of the LCD panel only to ensure 20 cm will be maintained if the user

places the device in their lap for use) and The transmitter module may not be co-located with any

other transmitter or antenna. As long as the 2 cond itions above are met, further transmitter testing

will not be required.

However, the OEM integrator is still responsible for testing their end-product for any

additional compliance requirements required with this module installed (for example,

digital device emissions, PC peripheral requirements, etc.).

IMPORTANT NOTE: In the event that these conditions can not be met(for example certain

laptop

configurations or co-location with another transmitter), then the FCC authorization is no

longer considered valid and the FCC ID can not be used on the final

product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end

product (including the transmitter) and obtaining a separate FCC authorization.

End Product Labeling

This transmitter module is authorized only for use in devices where the antenna may be installed

such that 20 cm may be maintained between the antenna and users (for example access points,

routers, wireless ASDL modems, certain laptop configurations, and similar equipment). The final

end product must be labeled in a visible area with the following: "Contains TX FCC ID:M4Y-

AN622V01 ".

Summary of content (4 pages)

PAGE 1
FCC Statement Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 2
RF Exposure Manual Information That Must be Included The users manual for end users must include the following information in a prominent location "IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
PAGE 3
1. Introduction IEEE802.11 a/b/g/n dual band 2x2 Wireless Network Mini PCI Adapter is the perfect solution for your wireless network applications based on the IEEE 802.11n standard offering a data rate of up to 300Mbps in a wireless LAN environment. AN-622 can easily integrate into a wide range of devices such as Access Point, Router, ATUR, Printer Server series, IP Camera series and Internet Video Server, etc.
PAGE 4
extension cables, frayed power cords, and missing safety grounds. λ If an electrical accident occurs, proceed as follows: – Use caution; do not become a victim yourself. – Disconnect power from the system. – If possible, send another person to get medical aid. Otherwise, assess the condition of the victim and then call for help. – Determine if the person needs rescue breathing or external cardiac compressions; then take appropriate action. 3.