Installation Instructions

ManualsBrandsZ Com ManualsComputers & Accessories54Mbps Wireless Mini PCI Adapter

FCC Statement

Warning: Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user authority to operate the equipment.

54Mbps IEEE802.11g Wireless Network Mini PCI Adapter complies with Part 15 of the FCC

Rules. Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

The user’s manual or instruction manual for an intentional or unintentional radiator

shall caution the user that changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to operate the

equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is needed.

Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

To comply with FCC RF exposure compliance requirements, a separation distance of at

least 20 cm must be maintained between the antenna of this device and all persons.

This Transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter

This device is intended only for OEM integrators under the following conditions:

The antenna must be installed such that 20 cm is maintained between the antenna and

users. The transmitter module may not be co-located with any other transmitter or

antenna. As long as the 2 conditions above are met, further transmitter testing will not

be required. However, the OEM integrator is still responsible for testing their

end-product for any additional compliance requirements required with this module

installed (for example, digital device emissions, PC peripheral requirements, etc.).

IMPORTANT NOTE: In the event that these conditions can not be met (for example

certain laptop configurations or co-location with another transmitter), then the FCC

authorization is no longer considered valid and the FCC ID can not be used on the final

product. In these circumstances, the OEM integrator will be responsible for

Summary of content (4 pages)

PAGE 1
FCC Statement Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. 54Mbps IEEE802.11g Wireless Network Mini PCI Adapter complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 2
re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example access points, routers, wireless ASDL modems and similar equipment). The final end product must be labeled in a visible area with the following: "Contains TX FCC ID:M4Y-0XG650 ".
PAGE 3
. . . . . Freedom to Roam While staying Connected 54 Mbps High-Speed Transfer Rate Two UF-L Connectors for External Antenna Support Antenna diversity for Better Sensitivity Lower Power Consumption. 3. Specification HOST INTERFACE 33MHz, 32-bit MiniPCI, Type III B (support TI VLYNQ bus) RADIO Chipset TI TNETW1130 ; Radia RC2422B & RC2326 Antenna Two UFL Connectors Frequency USA (FCC) 11 Channels: 2.412GHz~2.462GHz Europe (ETSI) 13 Channels : 2.412GHz~2.472GHz Japan (TELEC) 14 Channels : 2.412GHz~2.
PAGE 4
.2. Safety Recommendations The safety guidelines are as follows: λ Keep the board area clear and dust-free before, during, and after installation. λ Keep tools away from walk areas where you and others could fall over them. λ Do not wear loose clothing or jewelry, such as earrings, bracelets, or chains, that could get caught in the board. λ Wear safety glasses if you are working under any conditions that might be hazardous to your eyes.