Z CAM USB WIFI 5G Module WIFIM5G01 WiFi 802.
CONTENTS 1. Introduction.................................................................................................................1 2. Features........................................................................................................................2 3. General Specification..................................................................................................3 3.1 General Specification...........................................................................................
1. Introduction Shenzhen ImagineVision Technology Limited announce a low-cost and high-power consumption module which has 5g of the WiFi functionalities. The highly integrated module makes the possibilities of web browsing, VoIP, Long-distance audio and video transmission,Wireless HDMI Extender applications. With seamless roaming capabilities and advanced security, also could interact with different vendors’ 802.11a/n 2x2 5G only Access Points in the wireless LAN.
2. Features ⚫ ⚫ ⚫ ⚫ ⚫ Highly integrated wireless local area network(WLAN) system-on-chip (SOC) for 5 GHZ 802.11a/n WLAN applications. Dual-stream spatial multiplexing up to 300 Mbps data rate. Supports 20/40MHz Bandwidth Supports USB interface for WLAN. Integrated high power FEM. A simplified block diagram of the module is depicted in the figure below.
3. General Specification 3.1 General Specification Model Name WIFIM5G01 Product Description Support WiFi Dimension L x W x H: 27 x 20 x 2.3 (typical) mm WiFi Interface Support USB2.0 Operating temperature -30°C to 85°C Storage temperature -40°C to 125°C Humidity Operating Humidity 10% to 95% Non-Condensing 3.1.2 Recommended Operating Rating Operating Temperature VCC5V Min. Typ. Max. -30 25 85 4.8 5.0 5.2 Unit deg.C V 3.1.
4. WiFi RF Specification 4.1 5GHz RF Specification Feature Description WLAN Standard IEEE 802.11a/n 2x2, WiFi compliant Frequency Range 5180-5240 MHz, 5745-5825 MHz Number of Channels 5.0GHz:Please see the table1 Output Power 18.85dBm max.
SISO Receive Sensitivity (11n,40MHz) @10% PER MIMO Receive Sensitivity (11n,40MHz) @10% PER Maximum Input Level 15GHz(20MHz) - MCS=3 PER @ -83 dBm ≤-78 - MCS=4 PER @ -79 dBm ≤-74 - MCS=5 PER @ -74 dBm ≤-68 - MCS=6 PER @ -73 dBm ≤-66 - MCS=7 PER @ -71 dBm ≤-64 - MCS=8 PER @ -88 dBm ≤-84 - MCS=15 PER @ -68 dBm ≤-63 - MCS=0 PER @ -85 dBm ≤-82 - MCS=1 PER @ -82 dBm ≤-79 - MCS=2 PER @ -80 dBm ≤-77 - MCS=3 PER @ -77 dBm ≤-74 - MCS=4 PER @ -73 dBm ≤-70 - MCS=5 PER @ -72 dBm
5. Pin Assignments NO. Name Type Description Module working enable,High: power on,low: power off. 1 POWER_EN 2 WPS I/O 3 GND - 4 D+ I/O USB2.0 Data+ 5 D- I/O USB2.0 Data- 6 VDD5V P 5V Power Input 7 LED O Driving LED to indicate WiFi state 8 GND - Ground 9 RF1 I/O 5G WiFi RF signal pin1 10 RF0 I/O 5G WiFi RF signal pin0 11 GND - I 3.
6. Dimensions 6.
6.
7.
8. Recommended Reflow Profile Referred to IPC/JEDEC standard. Peak Temperature: <250°C Number of Times: 2 times 2.
9. Package Information Layer size: L300.0*W240.0 mm Layer material: PVC Carton size: L310.0*W260.0*H220.
10. Integration Introductions 2.2 This modular transmitter complies with FCC Rules Part 15, Subpart E 15.407. 2.3 Specific operational use conditions Antenna Change Notice to Host manufacturer Recommend using antenna which certified with this module mentioned in this manual.
2.8 Labelling and compliance statement instruction for host product manufacturer Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC ID: 2AENNWFM5G01” any similar wording that expresses the same meaning may be used. § 15.
2.10 Disclaimer on additional testing, Part 15 Subpart B compliance of Host Product This modular transmitter is only FCC authorized for the specific rule parts listed on our grant, host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer in any case shall ensure host product which is installed and operating with the module is in compliant with Part 15B requirements.