7. Open the heater roller. • Press the heater roller open/ close lever to the [OPEN]. • Then the hook is unlocked and you can open the heater roller. CAUTION Be careful not to touch the surface of heater roller because it is very hot. • Remove the remaining packing paper in the heater roller. 8. Open the heater roller cover Preventing clasp for blowing up 9. Pull up the preventing clasp for blowing up.
10. Clean the heater roller. • Remove dirt from the heater roller using the heater roller cleaning brush (provided). CAUTION Be careful not to touch the surface of heater roller because it is very hot. • Clean it while rotating it by pressing the [Heater Roller RW] switch. 11. Clean the preventing clasp for blowing up. • Clean the preventing clasp for blowing up with an alcohol-moistened and soft cloth.
13. Clean the paper guide. • Wipe the paper guide with a soft water-moistened cloth. • After cleaning, wipe the paper guide again with a dry soft cloth. WARNING Paper guide Do not touch the heater roller and its surrounding part during heating or right after turning off the power because they are high temperature. Otherwise, it may cause a burn injury. 14. Close the heater roller cover. • After cleaning, press the [Heater roller RW] switch and [Heater roller FW] switch together.
16. Pass the packing paper through the heater roller. • Open the packing machine. • Open the packing paper to wrap the paper guide, then pass the packing paper. Paper guide ‵⁞⁗⁓ ⁛⁙‒‾ ⁗⁓⁖⁗ ‵⁞⁗⁓⁛⁙‒‾⁗⁓⁖⁗ N PE ▼ O • Pass the packing paper through the heater roller. CAUTION Be careful not to touch the surface of heater roller because it is very hot. Position to join the packing paper and the guide roller Set the top edge of cleaning leader above the side seal roller.
(1) 9. Close the heater roller. (2) (1) Hold the lever and set the hook. (2) Close the lever. Hook 18. Feed the packing paper. • Press the [Heater roller RW] switch to feed the packing paper. 19. Cut the packing paper. • Check that the packing paper is sealed correctly, and press the [Cutter] switch to cut the packing paper. • Then, remove the cut packing paper. CAUTION Be careful not to feed the cut packing paper to the conveyor because the conveyor will work when you press the [Cutter] switch.
20. Close the conveyor. • Hold the conveyor's handle like the left image, and push the conveyor. • Push the conveyor until you hear a clicking noise. 21. Return the packing unit to the original position. • Push the packing unit while holding its open/close lever. • Push the packing unit until you hear a clicking noise. 22. Return the packing base to the original position. • Unlock the packing base. • Push the packing base while holding its handle.
その他 Troubleshooting Symptom The machine does not operate. The edge of the paper is displaced. The error cannot be released even after packing paper has been refilled. The print is so light even after the ink ribbon has been replaced with a new one. Cause Measure to be taken The power cord is disconnected. Insert the power cord plug all the way. (P15) The breaker is [OFF]. Turn [ON] the breaker. (P16) The heater roller is not heated yet. Wait until the rapid heating is completed.
Warning errors If you misuse the machine or any failure occurs in the packing machine, warning (error) numbers and messages are displayed on the touch panel. After stopping the sound alarm, take measures for the warnings and errors. If you cannot release errors even after you have taken measures, contact with your nearest Yuyama’s sales office. 1. Touch [MUTE]. • The sound alarm stops. • Take measures for the warning (or the error). Read the next page for how to take measures for each warning (error). 2.
■■ List of Warnings Display number Description C00 Paper jam warning C02 Paper out warning The paper is out. Replace the paper with new one and then touch [RESUME]. (P55) C03 Remaining paper warning The remaining paper is insufficient. Replace the paper with new one. C04 LPU out position warning The packing unit is open. Insert the paper all the way and then touch [RESUME]. (P59) C05 DTA UT position warning The DTA unit is open. Insert the DTA unit all the way and touch [RESUME].
■■ List of Warnings (continued) Display number Description Cause Measure to be taken C20 Dirty tablet route warning The machine detects the tablet except when you remove and insert the cassette and the machine dispenses the tablets. C21 Cassette jam warning Tablets are jammed in the cassette. Remove jammed tablets in the cassette and then touch [RESUME]. C22 Lower door open warning The lower door is open. Close the lower door and then touch [RESUME].
■■ List of Warnings (continued) Display number Description Cause C48 Dirty tablet route warning The machine detects the tablet except when you remove and insert the cassette and the machine dispenses the tablets. C50 Tray connection warning The DTA tray is not set at the correct position. C51 Ribbon insertion warning The ink ribbon is not set at the correct position. C52 C65 Ribbon out of position warning The correct ribbon is not set on the machine.
■■ List of Errors Display number Description Part where the error occured E00 Roller home error Heater roller E04 Heater temp error Heater roller E05 Printer head high temp error E06 Cutter home error Cutter E11 Roller alarm error Heater roller E15 Printer board error E16 Printer head open Printer head position error E17 Printer head close Printer head position error E20 Revolver close position error E21 Revolve middle position error E30 Slide upper pusher error E31 Slide lower pus
■■ List of Errors (Continued) Display number Description E61 Outer carousel feed error E62 Outer carousel time out error E63 Inner carousel feed error E64 Inner carousel time out error Part where the error occured Cylinder E69 LED lighting error DTA tray E70 V-holder error Measure to be taken Touch [RESUME]. (If the error cannot be released, turn off and on the breaker.) * Touch [RESUME] and release the error. After the error is released, the LED will light up.
■■ List of Errors (Continued) Display number Part where the error occured E80 DTA signal error E81 V-holder signal error E82 Slide signal error E83 Cassette signal error E91 EEPROM writing error E92 Cassette UT comm. error E93 Internal parity error E95 Inside the packing Fill duplicate error machine or personal computer E96 Internal comm. error E98 Fil ID error E99 EEPROM error F01-99 * Description Internal error Measure to be taken Inside the packing machine Touch [RESUME].
Specification Name Full automatic tablet packing machine “PROUD” Model YS-TR-260FDSII YS-TR-330FDSII YS-TR-406FDSII YS-TR-520FDSII YS-TR-590FDSII Dispensing size Width: 60, 70, 76, 80 or 90 x Height: 70mm (double-folded paper) Packing paper (type) Cello-polly Packing speed Up to 60 pouches/minute Tablet detection method Photo sensor system Tablet supply method Free fall Ink ribbon Normal type (black or color), half type (black) Pouch print New thermal printer: black/4 colors (cassette type)
Body weight Power Consumption power * YS-TR-260FDSII YS-TR-330FDSII Approx. 580 kg YS-TR-406FDSII Approx. 730 kg YS-TR-520FDSII YS-TR-590FDSII Approx. 1140 kg YS-TR-260FDSII YS-TR-330FDSII YS-TR-406FDSII AC100 V ± 10 V 50/60 Hz YS-TR-520FDSII YS-TR-590FDSII AC120 V ± 10 V 50/60 Hz YS-TR-260FDSII YS-TR-330FDSII 800 VA (MAX) YS-TR-406FDSII 1000 VA (MAX) YS-TR-520FDSII YS-TR-590FDSII 1400 VA (MAX) The packing paper and the ink ribbon vary depending on the factory specification.
Yuyama U.S.A. Inc IL Office 1513 Carmen Drive Elk Grove Village,IL60007 Yuyama U.S.A. Inc CA Office 17835 Sky Park Circle,Bldg 14 Ste.A Irvine,CA 92614 Yuyama U.S.A. Inc FL Office 6308 Benjamin Road,Suite 704 Tampa,FL 33637 Yuyama U.S.A.
