User's Manual

ManualsBrandsYuneec Technology ManualsElectronicsAircraft Simulator

USER MANUAL

INSTALLING THE SIMU-CONNECTOR

IMPORTANT NOTE: The text described in the User

Manual uses the YUNEEC ST10+ remote controller

as our example.

Connect the Simu-connector to the USB port on a

computor. If HID-compliant device shows in the

Universal Serial Bus, it indicates the Simu-connector

is installed successfully!

STEP 6)

Tap the SR number on the remote controller

screen first, then the Connection Status window will

pop up on your computer. Tap 'OK', and in the next

pop window tap 'OK' again.

STEP 7) Tap the return button [ ] twice to return

to the main interface.

NOTICE

: We recommend to activate the software

first, then switch on the romote controller.

NOTICE:

When the VOLTS, ALT, and G-SPD on the

right column show N/A on the remote controller

screen, the binding fails. Tap the Flight Settings and

repeat the binding processes till figures display on

the column.

BINDING THE SIMU-CONNECTOR TO THE

REMOTE CONTROLLER

NOTICE: You should first plug the Simu-connector,

then start the YunSim Flight Simulator software.

STEP 1)

Click the icon on the computer screen.

STEP 2)

Open the 'Radio' Menu, and choose 'Bind

YUNEEC USB receiver'.

STEP 3)

Switch on the ST10+ and move the

proportional Control Rate Slider on the right side of

the ST10+ to the uppermost (rabbit) position. Check

if the correct aircraft model is already established. If

there is no model on the top left corner on the

remote control screen, refer to the charpter called

BUILDING THE AIRCRAFT MODE.

STEP 4)

Tap the [ ] and choose [ ].

STEP 5)

After you set the remote controller into bind

mode, click 'OK' on the pop up window on the

computer screen.

BUILDING THE AIRCRAFT MODEL

STEP 1) Tap the [ ] on the right corner

of the ST10+, and then tap 'New Model' to create a

new aircraft.

STEP 2)

Input 'aircraft simulator' in the blank, choose

the TYPHOON model, and then tap 'Save'. Your new

model will have been created.

STEP 3)

Return to the main interface of the remote

controller and then refer to the the previous

charpter for Binding the Simu-connector to the

remote controller.

Model: Typhoon Welcome,Pilot 10:48:28 pm

Model Select

New Model Typhoon

Model: TYPHOON Welcome,Pilot 10:48:28 pm

Model

SR24S_39816

Camera

not connectednot connected

Edit Model

Please input name

TYPHOON

Reset

Save

STARTING THE FLIGHT SIMULATION

NOTICE: Before starting the flight simulator, the

remote controller should be switched to Rabbit mode.

STEP 1)

Click 'Simulation' on the computer screen,

and then click 'Start'. After doing so the aircraft

motors will start to spin.

STEP 2)

Slowly raise the left-hand stick to slightly

above the center position. TYPHOON will takeoff

and climb slowly (or raise the stick further until it

does). Return the stick to the center position when

TYPHOON reaches the desired altitude.

STEP 3)

Get familiar with Angle Mode, Smart Mode,

and Home Mode of the aircraft. Learn how to

change between each mode on your remote

controller.

STEP 4)

When the simulation completes, exit the

YunSim flight simulation software, disconnect the

simu-connector, and switch off the remote

controller.

NOTICE:

If the aircraft falls over, gets too close to

the pilot in the Angle Mode or too close to the

forest, the aircraft will reset to the original position.

ADDITIONAL FUNCTIONS:

IMPORTANT NOTE: You can update the software by

clicking ‘File’ then ‘Update’ in the menu on the top

left corner of the software interface.

Wind Control

The wind force and wind direction can be set in the

software under the 'Simulation' tab. Look for the

submenu called ‘wind’.

Radio Display

The remote control input will display on the screen

when you choose 'Radio display' when clicking the

'Simulation'. The size of the remote controller can

also be adjusted.

Any informaon above might be changed due to

the soware update. For the latest documents,

please check the oﬃcial website www.yuneec.com.

FCC STATEMENT:

This equipment has been tested and found to

comply with the limits for Part 15 of the FCC rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if

not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications.

However, there is no guarantee that interference will

not occur in a particular installation. If this

equipment does cause harmful interference to radio

or television reception, which can be determined by

turning the equipment off and on, the user is

encouraged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment to an outlet on a circuit

different from that to which the receiver is connected.

This device complies with part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

NOTE: This equipment has been tested and found

to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential

installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will

not occur in a particular installation. If this

equipment does cause harmful interference to radio

or television reception, which can be determined by

turning the equipment off and on, the user is

encouraged to try to correct the interference by one

or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment

and receiver.

—Connect the equipment into an outlet on a circuit

different from that to which the receiver is connect-

ed.

—Consult the dealer or an experienced radio/TV

technician for help.

RF EXPOSURE WARNING

This equipment must be installed and operated in

accordance with provided instructions and the

antenna(s) used for this transmitter must be installed

to provide a separation distance of at least 20 cm

from all persons and must not be co-located or

operating in conjunction with any other antenna or

transmitter. End-users and installers must be provide

with antenna installation instructions and transmitter

operating conditions for satisfying RF exposure

compliance.

IC RADIATION EXPOSURE STATEMENT FOR CANADA

This device complies with Industry Canada

licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2)

this device must accept any interference, including

interference that may cause undesired operation of

the device.

Le présent appareil est conforme aux CNR d'Indus-

trie Canada applicables aux appareils radio exempts

de licence. L'exploitation est autorisée aux deux

conditions suivantes : (1) l'appareil ne doit pas

produire de brouillage, et (2) l'utilisateur de

l'appareil doit accepter tout brouillage radioélec-

trique subi, même si le brouillage est susceptible

d'en compromettre le fonctionnement.

This equipment complies with IC RSS-102 radiation

exposure limit set forth for an uncontrolled environ-

ment.

Cet équipement respecte les limites d'exposition

aux rayonnements IC définies pour un environne-

ment non contrôlé

Watch Me Function

When in Smart Mode, press [ ] to switch the TYPOON

between the ‘Watch Me’ and ‘Follow me’ modes.

Follow Me is the default setting, and is ready to use

if the button is ORANGE. If it is GREY, it means the

ST10+ GPS is not ready yet. Please wait.

The simulator enables the camera to enter the

‘Watch Me’ function. In this function, the remote

controller will be tracked. No matter where it goes

or how it moves the camera will automatically tilt its

angle according to the controller.

Disabling GPS

You can disable the GPS by the following steps:

Step 1) Move the right-hand stick all the way to the

right and hold it there until step 2 is completed.

Step 2) Move the Flight Mode Selection Switch from

Smart to Home and Home to Smart mode 4 times in

3 seconds.

When GPS has been disabled successfully the

aircraft will emit an audible indication and the GPS

status on the ST10+ screen will show ‘Disabled’.

Also, the Main LED Status Indicator will flash purple

and the LED Status Indicators below the motors will

flash three times per second then will stay off for one

second.

Full Screen Mode

After the Simu-connector is successfully bound to

the remote controller, you can change the interface

into full screen mode by the following steps:

Step 1) Click 'Simulation' and choose the display

mode during your current simulation.

Step 2) Click 'Full screen mode', and then click 'OK'.

INTRODUCTION

Download the UAV Pilot software at xxxxxxx and

start your flight exploration with the Yuneec Flight

Simulator! With the Simu-connector, users can

experience real flight characteristics even when

sitting in front of a computer. The flight simulator -

with Simu-connector - is compatible with all remote

controllers supported by the Yuneec protocol, and

provides users with a realistic flight experience in a

safe, simulated environment. The Flight Simulator

can be controlled without any wires within 10m, and

features virtual telemetry data displayed on the

interface.

SPECIFICATIONS

Dimensions: 2.99x0.91x0.31 in (76x23x8mm)

Weight: 0.25±0.004oz (7±0.1g)

Frequence Range: 2405khz ~ 2480khz

Compatible devices: ST10/ST10+/ST24

Transmit Power: 4.5dbm

Working Current: 40mA

UAV-Pilot Flight Simulation - YUNEEC\Q500 TYPHOON

File Model Scenery Radio Simulation Language ?

Radio display

Bind YUNEEC USB receiver...

UAV-Pilot

In the Bind menu of the transmitter now select

the USB receiver SRxxx_xxxxx, then click OK

ok cancel

UAV-Pilot

In order to establish the connection, return to

the transmitters main screen by pressing the

transmitters back button twice.