User's Manual

ManualsBrandsYuding Scien and Technology ManualsElectronicsIndustrial remote control

H23-BB Series Remote Control User Manual

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions (1)this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-- Consult the dealer or an experienced radio/TV technician for help

The device has been evaluated to meet general RF exposure statement.

The device can be used in portable exposure condition without restriction

First, the warranty

Quality assurance

Gexun guarantees that this product will be in full compliance with

the published specifications when it leaves the factory, as long as it

is properly installed.

Can be used normally, but the company does not guarantee that the operation

of this product is uninterrupted or zero error.

Warranty period

This product enjoys a one-year warranty period from the date of shipment, to

ensure that customers will not have any problems in the product within one year.

If during the warranty period, as long as the product quality is proved to be

defective, the company is willing to repair. Any product that needs to be repaired

must be sent to the service office designated by the company. The customer must bear

the cost of the product to the service office. The service office of the company

will bear the return fee and return it during the warranty period. product.

Unincluded items

The above warranty does not include lossy parts such as buttons, relays, fuses,

Summary of content (6 pages)

PAGE 1
H23-BB Series Remote Control User Manual FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
PAGE 2
batteries, or damage caused by incorrect installation. It does not include failures caused by improper use by customers, irresistible causes, natural factors, inadequate maintenance, neglect of operating environment specifications, unauthorized changes, incorrect use, or customer-defined interfaces. 一、 Remarks 二、 ***The above warranty does not contain other warranties that are express or implied.
PAGE 3
appropriately, so the content will be revised at any time based on the new product without prior notice. 十六、 Operator precautions 十七、 1. Users must have received complete training in the F21-E2B series to familiarize themselves with the operation. 十八、 2. The operator must be in good health, be in good spirits, be able to identify and judge the safety of the operation, and have a qualification certificate. 十九、 3.
PAGE 4
status of the remote control function (including the relay output) to avoid inconsistent wiring. 二十九、 5. The receiver should not be installed in the electric control box. The correct installation method is to fix the receiver to the top of the electric control box (or external), and then insert the receiver output cable into the electric control box to make appropriate. wiring. 三十、 6. This series of remote control has 4 billion sets of security codes.
PAGE 5
key switch on the transmitter; E2S turns the rotary key switch to the "on" position, and E2M rotates the emergency stop button clockwise). Press the start button to complete the boot action (or boot according to the set boot mode). 3. Follow the functions set by the buttons on the transmitter to operate correctly. 4. After the operation is completed, proceed in the following order 1.
PAGE 6
GeXun