User Guide Garage Door Kit O/C SET SET DC5V+ DC5V- SIGNAL Garage Door Controller Garage Door Sensor YS4906-UC YS7705-UC
Contents WARNING····································································1 Product Requirements······················································1 Introduction············································· ·············· ····· ·· 2 Features······································································4 Set Up Garage Door Kit·····················································5 Installation··························· ··································· ····10 Using YoLink App with Gara
WARNING To prevent severe injury to persons, Do not let the children use this kit without adult supervision. Always wait until the garage door or gate to be completely closed. Please visit www.yosmart.com to check compatibility for your garage door opener from the garage door opener list. Product Requirements A YoLink Hub. A Garage Door Opener. The smartphone or tablet able to run iOS 9 or higher; Android 4.4 or higher.
Introduction Garage Door Controller YoLink Garage Door Controller can open or close your Garage Door anywhere, anytime. LED light s can show you the current status. See the explanation below: Green once Open/Close the garage door. Blinking Green Connecting to cloud. OPEN/CLOSE O/C Fast Blinking Green Paring with other devices (YoLink Control). SET SET BUTTON Slow Blinking Green Updating. Fast Blinking Red Unparing with other devices (YoLink Control).
Garage Door Sensor YoLink Garage Door Sensor can detect opening and closing of your Garage Door and send alert or trigger action. LED light s can show you the current status. See the explanation below: Red once Alert. Blinking Green Connecting to cloud. Fast Blinking Green Paring with other devices (YoLink Control). Slow Blinking Green Updating. SET Fast Blinking Red Unparing with other devices (YoLink Control). Blinking Red and Green Factory resetting.
Features Check Status Anywhere - Check device status. Easy to Control - CONVENIENTLY OPEN AND CLOSE your garage door with your mobile device anywhere, anytime. Open Alert - Remind you while the door is open for a set up time. Long Range - Up to 1,000 Feet between Hub and device. Real-time Status - Monitor the real-time state of door via YoLink App. Battery Status - Update surplus of battery power and send low battery alert. YoLink Control - Trigger an action of certain YoLink devices without internet.
Set Up Garage Door Kit Follow the steps below to set up your garage door kit via YoLink App. Step 1: Set up YoLink App Get the YoLink App from the Apple App Store or Google Play.
Step 2: Log in or sign up with YoLink account Open the App. Use your YoLink account to log in. If you don’t have a YoLink account, tap Sign up for an account and follow the steps to sign up an account.
Step 3: Add controller to YoLink App Tap the “ ” in YoLink App. Scan the QR Code on the device. You can customize the name, set the room, add to/remove from favorite. a. Name - Name Garage Door Controller. b. Room - Choose a room for Garage Door Controller. c. Favorite - Click “ ” icon to add/remove from Favorite. Tap the “Bind Device” to add the device to your YoLink account.
Step 4: Add sensor to YoLink App Tap the “ ” in YoLink App. Scan the QR Code on the device. You can customize the name, set the room, add to/remove from favorite. a. Name - Name Garage Door Sensor. b. Room - Choose a room for Garage Door Sensor. c. Favorite - Click “ ” icon to add/remove from Favorite. Tap the “Bind Device” to add the device to your YoLink account. Pair with a controller.
Step 5: Install and set up the device Follow the following page to install the device, power it on. And the device is ready to go. Follow the following page to install the device, press the SET button once. And the device is ready to go.
Installation Note Please add Garage Door Controller and Sensor to YoLink App before you set them up. Garage Door Controller Locate the 2 power terminals at the left of the controller. You will see “5V+”and “5V-” on it. Find your adapter and put the red wire of it in the “5V+” terminal. Put the black wire in the “5V-” terminal. Now there are 2 terminals named “signal” to be connected. First, put two wires in these two terminals.
Wiring Diagram: Locate the 2 terminals on the back of your garage opener.
Wiring Diagram: Locate the 2 terminals on the back of your button panel.
Garage Door Sensor Note Please dry clean the area first. Please stick the sensor at the inside top panel of the Garage Door. Please keep the arrow on the battery cover pointing to the right. Please use the double-side tape to stick the sensor to your garage door and make sure the sensor is stuck tightly.
Automation Automation allows you to set up “If this then that” rules so the devices can act automatically. Tap “Smart” to switch to Smart screen and tap “Automation”. Tap “ ” to create an automation. To set an Automation, you will need to set a trigger time, local weather condition, or choose a device with certain stage as a triggered condition. Then, select the response devices or Scenes.
Using YoLink App with Garage Door Kit Details You can customize the name, set the room, set the open alert, add to/ remove from favorite, check device history, set pairing with sensor. a. Name - Name your Garage Door Controller. b. Room - Choose a room for your garage door device. c. Open Alert - Set a time which you will able to receive an alert once your door has been open for that long. d. Favorite - Click Add/Remove the device from Favorite. a b c d e f g e.
YoLink Control YoLink Control is our unique “device to device” control technology. Under YoLink Control, the devices can be controlled without internet or Hub. Devices which send out command is called controller(Master). Devices which receive command and act accordingly is called responder(Receiver). You will need to set it up physically. Pairing Find a garage door sensor as controller(Master). Hold the set button for 5-10 seconds, the light will flash green quickly.
Unpairing Find the controller(Master) garage door sensor. Hold the set button for 10-15 seconds, the light will flash red quickly. Find the responder(Receiver) action device. Hold the set button for 10-15 seconds, the device will enter unpairing mode. SET The above two devices will unpair by themselves and the light stops flashing. When the garage door sensor is detected to be opened, the responder will no longer turn on.
YoLink Control Diagram SET SET opened closed turn off turn on Paired opened closed turn off turn off Unpaired 18
Maintaining the Garage Door Kit Firmware Update Ensure our customer have the best user experience. Highly recommend you could update our newest version firmware. Tap the “Garage Door” in App to go to its controls. Tap the “ ” icon at the top-right corner to go to details. Tap “Firmware”. The light will be slowly blinking green during the update and stop blinking when the update done.
Factory Reset Factory reset will erase all your settings and bring it back to default. After the factory reset, your device will still in your Yolink account. Hold the set button of controller for 20-25 seconds until the LED blinks red and green alternately. Factory reset will be done when the light stops flashing. You may factory reset the sensor following the same procedure.
Specifications Garage Door Controller Voltage: 5V DC Current: 1A Environment: Working Temperature: 0°C~40°C (32°F~104°F) Working Humidity: 10%~90% non-condensing Garage Door Sensor Voltage: 3V DC (2 - AAA battery) Environment: Working Temperature: 0°C~40°C (32°F~104°F) Working Humidity: 10%~90% non-condensing 21
Troubleshooting Garage Door Controller Problem Possible Reason Solution Hub is offline. Please reconnect your hub to the Internet and press the set button of Garage Door Controller once. Hub is powered off. Please power on the hub again and press the set button of Garage Door Controller once. Device does not power on. Please power on your device. Product defective. Please contact customer service. No action or light. Product defective. Please contact customer service. Other problems.
Garage Door Sensor Problem Possible Reason Solution Hub is offline. Please reconnect your hub to the Internet and press the set button of Garage Door Controller once. Hub is powered off. Please power on the hub again and press the set button of Garage Door Controller once. Device does not power on. Please power on your device. Product defective. Please contact customer service. Wrong direction. Incorrect installation. Please refer to the Installation chapter to install the device correctly.
If you are unable to get your garage door kit working Please contact us during business hours US Live Tech Support: 1-844-292-1947 M-F 9am - 5pm PST Email: support@YoSmart.com YoSmart Inc. 17165 Von Karman Avenue, Suite 105, Irvine, CA 92614 WARRANTY 2 Year Limited Electrical Warranty YoSmart warrants to the original residential user of this product that it will be free from defects in materials and workmanship, under normal use, for 1 year from the date of purchase.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations.