User Guide YS3603-UC YoLink Remote
Contents Introduction··············································· · 1 Features··················································· · 2 Device Supported ····· ····· ························ · ····· · 2 YoLink Control· ··· ········· ····························· ·· · · 3 Maintaining the YoLink Remote ···················· ······5 Specifications···············································7 Customer Ser vice and Warranty······················ ···8
Introduction With YoLink Remote, you can custom grouping plugs, switches, and outlets and control them by one button. No hub or internet is required. LED lights can show you the current status. See the explanation below: Green Once Trigger an action. Fast Blinking Green Set up connection with devices. Fast Blinking Red ON OFF Remove connection with devices. Blinking Red and Green Factory resetting.
Features YoLink Control - No internet is required, turn on or off your YoLink devices after you set up your devices with the remote. Long Range - Up to 500 Feet between remote and device. Devices Supported YS6602-UC YoLink Plug YS6604-UC YoLink Plug Mini YS5705-UC In-wall Switch YS6704-UC In-wall Outlet YS4907-UC Gas/Water Valve YS6801-UC Smart Power Strip YS6802-UC Smart Switch Continuously updating ..
YoLink Control YoLink Control is our unique “device to device” control technology. Under YoLink Control, the devices can be controlled without internet or Hub. Device which send out command is called controller(Master). Device which receive command and act accordingly is called responder(Receiver). Controller and responder list will show you below. You will need to set it up physically. Pairing F i n d a Yo L i n k r e m o t e a s c o n t r o l l e r ( M a s t e r ) .
Un-pairing F i n d t h e c o n t r o l l e r ( M a s t e r ) Yo L i n k r e m o t e . Hold the OFF button for 10-15 seconds, the l i g h t w i l l fl a s h r e d q u i c k l y. Find the responder(Receiver) action device. Hold the power/set button for 10-15 seconds, the device will enter the un-pairing mode. OFF The above two devices will unpair by themselves and the light stops flashing. After unbundling, all the control buttons of YoLink Remote will no longer change status of the action device.
Maintaining the YoLink Remote Factory Reset Factory reset will erase all your settings and bring it back to default, which will remove all the connections with your pairing devices. Hold the ALL ON button for 20 seconds until the LED blinks red and green alternately. Factory reset will be done when the light stops flashing.
Battery Replace When no action triggers on the pairing devices or no light when press the button on remote, please replace the battery. Note Replace all your original batteries with new ones.
Specifications Voltage: 3V DC (2 - AAA Batter y) Environment: Working Temperature: 0°C~40°C (32°F~104°F) Working Humidity: 10%~90% non-condensing 7
If you are unable to get your remote working Please contact Our Customer Service during business hours US Live Tech Support: 1-844-292-1947 M-F 9am - 5pm PST Email: support@YoSmart.com YoSmart Inc. 17165 Von Karman Avenue, Suite 105, Irvine, CA 92614 WARRANTY 2 Year Limited Electrical Warranty YoSmart warrants to the original residential user of this product that it will be free from defects in materials and workmanship, under normal use, for 2 year from the date of purchase.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. The device has been evaluated to meet general RF exposure requirement.